Christie Digital Systems Matrix Hd4 Users Manual

Section 3: Operation  
3-72 020-100001-01 Rev. 01 (04/07) 
The Status LED Codes 
If the status code display on the back of the projector shows one of the following 
values, you have encountered a likely system error requiring the attention of a 
qualified service technician (see System Warnings and System Errors, above). 
Acknowledge and clear the error with 
Exit Exit from presentation level, or try 
resetting the projector by powering it off and on again, cooling when necessary. 
Consult Table 3.5 and...

 Section 3: Operation 
020-100001-01 Rev. 01 (04/07)  3-73. 
88  Red modular Formatter communication failure  89  Green modular Formatter communication failure 8A  Blue modular Formatter communication failure 93  Modular formatter architecture error 94  Modular formatter DMD mismatch 95  Modular formatter sequence mismatch MISCELLANEOUS A0  Unable to program the optional module  A1  Unable to power the optional module  A2  Unable to program the Dual Slot Backplane Module (DSBP) A3  Unable to program the...

Section 4 
Maintenance  
 
020-100001-01 Rev. 01 (04/07)  4-1 
 
 
The projector is an international regulatory agency approved product designed for safe 
and reliable operation. To assure complete safety at all times it is important to 
acknowledge the following precautions while operating the projector.  
 WARNING  
Always power down the projector using appropriate procedure 
and disconnect all power sources before cleaning or servicing. 
 WARNING  
Always remove the lens when shipping the projector....

Section 4: Maintenance  
4-2 020-100001-01 Rev. 01 (04/07)   
• Do not operate the projector close to water, such as near a swimming pool. Do not 
operate in extremely humid environments. 
• Do not place the projector on an unstable cart, stand or table. A projector and cart 
combination should be used with care. Sudden stops, excessive force and uneven 
surfaces may cause the projector and cart combination to overturn. 
• Only use Christie-approved ceiling mount fixture, if the projector is to be...

  Section 4: Maintenance 
020-100001-01 Rev. 01 (04/07)  4-3. 
• Do not set or rest items on the power cord. Place the projector in an area where 
the projector cord cannot be abused or damaged by persons walking on it or by 
objects rolling over it. 
• Operate the projector at the specified voltage only. Do not overload power outlets 
and extension cords as this can result in fire or shock hazards. 
• The projector is equipped with a three-wire plug having a third grounding pin. 
This is a safety...

Section 4: Maintenance  
4-4 020-100001-01 Rev. 01 (04/07)   
 
Table 4.1. Maintenance Guide 
Part Description Frequency Action 
Lens   As required  Clean the lens only when absolutely 
necessary. A small amount of dust on the 
lens has very little effect on picture quality. 
To clean: Use a soft lint-free cloth without 
any chemicals. Use only a high-quality 
coated optics cleaning fluid, which can be 
purchased from most camera supply stores. 
Apply the coated optics fluid directly onto 
the lint-free...

  Section 4: Maintenance 
020-100001-01 Rev. 01 (04/07)  4-5. 
 
The IR Remote Keypad uses two AA size, 1.5V batteries (preferably alkaline). To 
install new batteries:  
1) Open the battery 
compartment at the backside 
of the keypad by placing your 
thumb in the oval depression 
and sliding the cover out about 
½ inch. See Figure 4.1. 
Remove the old batteries and 
properly discard. Wait a 
minute or two.  
2) Place the new batteries in 
the compartment, orienting the 
positive/negative of each...

Section 4: Maintenance  
4-6 020-100001-01 Rev. 01 (04/07)   
Table 4.2. Lamp/Filter Replacement Kits 
Projector ModelModel Number Lamp Type (Watts) Lamp/Filter Kit Required 
Mirage S+3K 38-DSP102-x4 03-000832-51P 
Mirage HD3 104-012101-xx 003-120118-01 
Matrix S+2K 38-DSP102-x6 03-000832-51P 
Matrix HD2 104-023101-xx 003-120118-01 
DLV1400-DX 38-DSP102-x5 03-000832-51P 
DLV1920-DX 104-017101-xx 500W 
003-120118-01 
Christie DS+6K 38-DSP104-x5 03-000833-51P 
Christie DS+5Kc 38-DSP104-x8 03-000833-51P...

  Section 4: Maintenance 
020-100001-01 Rev. 01 (04/07)  4-7. 
1. TURN THE LAMP OFF 
Press 
 (power) to turn the lamp off. Allow the cooling fans to stop 
automatically (within approximately five minutes) before proceeding with Step 2. 
This wait period is also required to allow the lamp to sufficiently cool before 
handling. 
2. UNPLUG THE PROJECTOR 
When the cooling fans have stopped, turn the projector’s main switch off, and 
unplug. 
 WARNING  
Always power down and unplug the projector prior to...