Christie Digital Systems Lx400 User Manual

							29
IMAGE Menu
IMAGE Menu
From the IMAGE menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
Item Description
ASPECTUsing the ▲/▼ buttons switches the mode for aspect ratio. 
For an RGB signal
NORMAL 
 4:3 
 16:9 
 SMALL
         
For an HDMI signal
NORMAL 
 4:3 
 16:9 
 14:9 
 SMALL
         
For a Video signal, S-video signal or Component video signal
4:3 
 16:9 
 14:9 
 SMALL
     
For no signal
4:3 (fixed)
• The NORMAL mode keeps the original aspect ratio of the signal.
OVER SCANUsing the ▲/▼ buttons adjusts the over-scan ratio.
Large (It reduces picture) 
 Small (It magnifies picture)
• 
This item can be selected only for a video, s-video, component and HDMI signal.• When this adjustment is too large, certain degradation may appear 
at the frame area of the picture. In such a case, please adjust small.
V POSITIONUsing the ▲/▼ buttons adjusts the vertical position.
Up 
 Down
•
 Over-adjusting the vertical position may cause noise to appear on the screen. If this 
occurs please reset the vertical position to the default setting. Pressing the RESET button 
when the V POSITION is selected will reset the V POSITION to the default setting.
• When this function is performed on a video signal, s-video signal, or component video 
signal of 480i@60 or 576i@50 input from the COMPONENT port, the range of this 
adjustment depends on the OVER SCAN 
(above) setting. It is not possible to adjust 
when the OVER SCAN is set to 10.
H POSITIONUsing the ▲/▼ buttons adjusts the horizontal position.
Left 
 Right
• 
Over-adjusting the horizontal position may cause noise to appear on the screen. If this 
occurs please reset the horizontal position to the default setting. Pressing the RESET 
button when the H POSITION is selected will reset the H POSITION to the default setting.
• When this function is performed on a video signal, s-video signal, or component video 
signal of 480i@60 or 576i@50 input from the COMPONENT port, the range of this 
adjustment depends on the OVER SCAN 
(above) setting. It is not possible to adjust 
when the OVER SCAN is set to 10.
(continued on next page)
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							30
IMAGE Menu
IMAGE Menu (continued)
Item Description
H PHASE
Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker.
Right 
 Left
• This item can be selected only for an RGB signal or a component 
video signal. (except 480i@60, 576i@50, SCART RGB input from 
the COMPONENT port)
H SIZEUsing the ▲/▼ buttons adjusts the horizontal size.
Large 
 Small
• This item can be selected only for an RGB signal.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
by pressing the RESET button on the remote control during this 
operation.
AUTO ADJUST 
EXECUTESelecting this item performs the automatic adjustment feature.
For an RGB signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically set to default. 
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal and s-video signal
The video format best suited for the respective input signal will 
be selected automatically. This function is available only when 
the AUTO is selected for the VIDEO FORMAT item in the INPUT 
menu (
32). The vertical position and horizontal position will be 
automatically set to the default.
For a component video signal
The vertical position, horizontal position and horizontal phase will 
be automatically set to the default.
• The automatic adjustment operation requires approx. 10 seconds. 
Also please note that it may not function correctly with some input. 
When this function is performed for a video signal, a certain extra 
such as a line may appear outside a picture.
• The items adjusted by this function may vary when the FINE or 
DISABLE is selected for the AUTO ADJUST item of the SERVICE 
item in the OPTION menu (
45).
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							31
INPUT Menu
INPUT Menu
From the INPUT menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor 
button on the projector or remote control, or ENTER 
button on the remote control to execute the item. Then 
perform it according to the following table.
Item Description
PROGRESSIVEUsing the ▲/▼ buttons switches the progress mode.
TV 
 FILM 
 TURN OFF
  
• This function is performed only for an interlaced signal at 
the VIDEO or S-VIDEO input, and for 480i@60, 576i@50 or 
1080i@50/60 signal at the COMPONENT VIDEO or HDMI input.
• When TV or FILM is selected, the screen image will be sharp. 
FILM adapts to the 2-3 Pull-Down conversion system. But these 
may cause a certain defect (for example, jagged line) of the picture 
for a quick moving object. In such a case, please select TURN OFF, 
even though the screen image may lose the sharpness.
VIDEO NRUsing the ▲/▼ buttons switches the noise reduction mode.
HIGH 
 MID 
 LOW
   
• This function is performed only for the VIDEO or S-VIDEO 
input, and for 480i@60, 576i@50 or 1080i@50/60 signal at the 
COMPONENT VIDEO or HDMI input.
• When this function is excessive, it may cause a certain 
degradation of the picture. 
3D-YCSUsing the ▲/▼ buttons switches the 3D-YCS mode.
STILL 
 MOVIE 
 TURN OFF
     
• This function performs only at a VIDEO input of NTSC, and PAL.
• MOVIE is the mode for images with a lot of motions like movies, 
and STILL is the mode for images with few motions or completely 
still ones like slides.
COLOR SPACEUsing the ▲/▼ buttons switches the mode for color space.
AUTO 
 RGB 
 SMPTE240 
 REC709 
 REC601
      
• This item can be selected only for an RGB signal or a component 
video signal (except 480i@60, 576i@50 and SCART RGB).
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a 
case, it might be good to select a suitable mode except AUTO.
(continued on next page)
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							32
INPUT Menu
INPUT Menu (continued)
Item Description
COMPONENTUsing the ▲/▼ buttons switches the function of the COMPONENT 
(Y, C
B/PB, CR/PR) port.
COMPONENT 
 SCART RGB
When the SCART RGB is selected, the COMPONENT (Y, C
B/PB, 
CR/PR) and VIDEO ports will function as a SCART RGB port. A 
SCART adapter or SCART cable is required for a SCART RGB 
input to the projector. For details, contact your dealer.
VIDEO FORMATSet the video format for the s-video port and video port.
(1) Use the ◄/► buttons to select the input port.
(2) Using the ▲/▼ buttons switches the mode 
for video format.
AUTO  
  NTSC  
  PAL  
  SECAM
      N-PAL 
 M-PAL 
 NTSC4.43 
• This item is performed only for a video signal 
from the VIDEO port or the S-VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the 
picture becomes unstable (e.g. an irregular picture, lack of color), 
please select the mode according to the input signal.
HDMIUsing the ▲/▼ cursor buttons changes the HDMI signal mode.
AUTO 
 NORMAL 
 ENHANCED
     
Feature
AUTO Selecting the optimum mode automatically.
NORMAL Suitable for DVD signals (16-235)
ENHANCED Suitable for VGA signals (0-255)
• If the contrast of the screen image is too strong or too weak, try 
finding a more suitable mode.
VIDEOAUDIO IN 1
AUDIO IN 2
S-VIDEO
 R   L R   L
   AUDIO IN 3    AUDIO IN 4
CB/PBY
CR/PR
SCART OUT
Video G B R
(continued on next page)
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							33
INPUT Menu
Item Description
FRAME LOCKSet the frame lock function on/off for each port.
(1) Use the ▲/▼ buttons to select one of 
following ports.
RGB1 
 RGB2 
 HDMI
                QUIT
(2) Use the ◄/► buttons to turns the frame 
lock function on/off .
TURN ON 
 TURN OFF
• This item can be performed only on a signal  
with a vertical frequency of 50 to 60 Hz.
• When the TURN ON is selected, a moving pictures are displayed 
more smoothly.
• This function may cause a certain degradation of the picture. In 
such a case, please select the TURN OFF.
RGB INSet the RGB input signal type for the RGB port.
(1) Use the ◄/► buttons to select the RGB 
port to be set.
RGB1 
 RGB2
(2) Use the ▲/▼ buttons to select the RGB 
input signal type.
AUTO 
 SYNC ON G OFF
• Selecting the AUTO mode allows you to input a sync on G signal 
or component signal from the port.
• In the AUTO mode, the picture may be distorted with certain 
input signals. In such a case, remove the signal connector so that 
no signal is received and select the SYNC ON G OFF, and then 
reconnect the signal.
INPUT Menu (continued)
(continued on next page)
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							34
INPUT Menu
INPUT Menu (continued)
Item Description
RESOLUTIONThe resolution for the RGB1 and RGB2 input signals can be set on 
this projector.
(1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and 
press the ► button.
The RESOLUTION menu will be displayed.
(2)  In the RESOLUTION menu select the 
resolution you wish to display using the ▲/▼ 
buttons. 
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3) Pressing the ► or ENTER button when 
selecting a STANDARD resolution will 
automatically adjust the horizontal and 
vertical positions, clock phase and horizontal 
size.
 The INPUT-INFORMATION dialog (
46) will 
be displayed.
(4) To set a custom resolution use the  
▲/▼ buttons to select the CUSTOM and 
the CUSTOM RESOLUTION BOX will be 
displayed. Set the horizontal (HORZ) and 
vertical (VERT) resolutions using the  
▲/▼/◄/► buttons.
It is not guaranteed to work this function 
properly on any resolutions.
(5) To save the setting place the cursor on the 
right-most digit and press the ► button.
The horizontal and vertical positions, clock 
phase and horizontal size will be automatically 
adjusted.
After the INPUT-INFORMATION (
46) dialog 
has displayed for about 10 seconds the 
screen will return to the RESOLUTION menu 
displaying the changed resolution.
(6) To revert back to the previous resolution 
without saving changes place the cursor on 
the left-most digit and press the ◄ button.
The screen will then return to the RESOLUTION menu displaying the 
previous resolution.
• For some pictures, this function may not work well.
RESOLUTION MENU
CUSTOM RESOLUTION 
BOX
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							35
SETUP Menu
SETUP Menu
From the SETUP menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
according to the following table.
Item Description
AUTO 
KEYSTONE 
EXECUTESelecting this item performs the Automatic keystone distortion 
correction. Projector automatically corrects vertical keystone 
distortion due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the menu. 
When the slant of the projector is changed, execute this function 
again.
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When V:INVERT or H&V:INVERT is selected to the MIRROR item 
in the SETUP menu, if the projector screen is inclined or angled 
downward, this function may not work correctly.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• When the projector is placed on the level (about ±3°), this function 
may not work.
• When the projector is inclined to near ±30 degree or over, this 
function may not work well.
• When the vertical lens shift is not set fully upward (not set fully 
downward for the optional lens type FL-601 only (
45)), this 
function may not work well.
• When the horizontal lens shift is not set to the center, this function 
may not work well.
• This function will be unavailable when the Transition Detector is 
on (
51).
KEYSTONE 
Using the ▲/▼ buttons corrects the vertical keystone distortion.
Shrink the top of the image 
 Shrink the bottom of the image
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the horizontal lens shift is not set to the center, this function 
may not work well.
• This function will be unavailable when the Transition Detector is 
on (
51).
(continued on next page)
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							36
SETUP Menu
Item Description
KEYSTONE 
Using the ▲/▼ buttons corrects the horizontal keystone distortion.
Shrink the right of the image 
 Shrink the left of the image
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• When the vertical lens shift is not set fully upward (not set fully 
downward for the optional lens type FL-601 only (
45)), this 
function may not work well.
• This function will be unavailable when the Transition Detector is 
on (
51).
WHISPERUsing the ▲/▼ buttons turns off/on the whisper mode.
NORMAL 
 WHISPER
• When the WHISPER is selected, acoustic noise and screen 
brightness are reduced.
MIRRORUsing the ▲/▼ buttons switches the mode for mirror status.
NORMAL 
 H:INVERT 
 V:INVERT 
 H&V:INVERT
 
If the Transition Detector is TURN ON and MIRROR status is 
changed, Transition Detector Alarm (
51) will be displayed when 
projector is restarted after the power switch is turned off.
SETUP Menu (continued)
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							37
AUDIO Menu
AUDIO Menu
From the AUDIO menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
Item Description
VOLUMEUsing the ▲/▼ buttons adjusts the volume.
High 
 Low
TREBLEUsing the ▲/▼ buttons adjusts the treble level.
High 
 Low
BASSUsing the ▲/▼ buttons adjusts the bass level. 
High 
 Low
SRS WOWUsing the ▲/▼ buttons switches the mode for SRS WOW mode. 
HIGH 
 MID 
 OFF
    
• SRS WOW™ accomplishes this by providing a panoramic three-
dimensional audio image that extends the sound field in both the 
horizontal and vertical planes, and lowers the perceived bass 
response well beyond the low frequency limitations of the drivers. 
Adjust it depending on the user's preference.
SPEAKERUsing the ▲/▼ buttons turns the speaker function on/off. 
TURN ON 
 TURN OFF
• When the TURN ON is selected the built-in speaker works.
AUDIOAllocates the audio ports.
(1) Choose a picture input port using the ▲/▼ 
buttons.
          RGB1
  
  RGB2  
  HDMI 
QUIT 
 VIDEO 
 S-VIDEO 
 COMPONENT
(2) Select the audio port to be interlocked with 
the input port using the ◄/► buttons.
1 
 2 
 3 
 4 
 
 
 H
• H is abbreviation of HDMI.
• H can be selected for HDMI port only. When H is selected, the 
audio signal to HDMI port will be output if HDMI is chosen as a 
display source.
• When 
 is selected for an input, the audio will not be output if the 
input is chosen as a display source.
HDMI AUDIOThe HDMI AUDIO is set to 1 as default. In case the HDMI audio 
does not work well, try 2.
1 
 2 
• The speaker sound may distorted or the case may be trembling when 
the volume is too high or treble/bass is emphasized or WOW is activated. In that 
case, make the volume reduced, bass/treble low or WOW effect to be weakend.NOTE
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009) 
						

							38
SCREEN Menu
SCREEN Menu
From the SCREEN menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
Item Description
LANGUAGE
Using the ▲/▼ buttons switches the OSD (On Screen Display) language.
SUOMI  POLSKI  TÜRKÇE ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO
NORSK  NEDERLANDS  PORTUGUÊS  ãÄ.†
                  SVENSKA 
MENU POSITIONUsing the ◄/►/▲/▼ buttons adjusts the menu position.
To quit the operation, press the MENU button on the remote control 
or keep no operation for about 10 seconds.
BLANKUsing the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature
 
(22). It is displayed by pressing the BLANK button on the remote 
control.
MyScreen 
 ORIGINAL 
 BLUE 
 WHITE 
 BLACK
  
Feature
MyScreenScreen can be registered by the MyScreen item 
(40).
ORIGINAL Screen preset as the standard screen.
BLUE, WHITE, 
BLACKPlain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the plain black screen after several minutes.
(continued on next page)
LX400 User Manual - Operating Guide 020-000169-01 Rev. 1 (04-2009)