Home > Christie Digital Systems > Projector > Christie Digital Systems Ds+60 Users Manual

Christie Digital Systems Ds+60 Users Manual

Here you can view all the pages of manual Christie Digital Systems Ds+60 Users Manual. The Christie Digital Systems manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 21

Section 2: Installation and Setup 
 
Christie DS+60 User’s Manual     2-15  
 
As an alternative to the projector’s keypad or remote, you may wish to communicate 
with the projector using a PC or other controller. Such a device sends commands and 
receives feedback via serial links (RS232 and RS422), Ethernet or GPIO 
communications to the projector, all described below. 
As desired, direct the projector’s IR remote keypad towards the display screen or the 
projector’s IR sensors. Alternatively, connect...

Page 22

Section 2: Installation and Setup 
2-16   Christie DS+60 User’s Manual  
 
Figure 2.15. RS232 Network 
Connecting RS-422 
If you wish to control the projector with a computer and or other controlling device 
with RS-422 capability, connect a RS-422 serial communication cable between the 
computer and the RS-422 port on the projector. RS-422 is better suited for serial 
communication over long distances then is RS-232 communication.  
 Use the RS-422 port only if your device had RS-422 capability – always...

Page 23

Section 2: Installation and Setup 
 
Christie DS+60 User’s Manual     2-17  
Regardless of how it is assigned, once a projector has a valid and unique address it 
will respond to commands sent to this address. To determine the projector’s current IP 
address, consult the Status or Communications menus. 
Refer to Section 3 for further information about setting up and using a projector 
connected via Ethernet. 
Log on to www.christiedigital.com for detailed information on ChristieNET. 
 
The GPIO (General...

Page 24


				            

Page 25

Section 3 
Operation  
 
  Christie DS+60 User’s Manual     3-1 
 
This section explains how to effectively operate the projector once it has been 
installed. It is recommended that you read this section and familiarize yourself with 
the components and the available menu options before you begin using your projector 
for the first time. 
 1 Top cover 9 Air vents 
2 Built-in keypad 10 Rear input panel 
3 AC receptacle 11 Rear IR sensor 
4 Adjustable feet (3) 12 Rear exhaust  
5 Projection lens 13 Lamp 1...

Page 26

Section 3: Operation 
3-2   Christie DS+60 User’s Manual  
(3) The AC receptacle is located on the right side of the projector (opposite side of 
lamp doors). Use this outlet to plug in an appropriately rated line cord. See 2.6 Power 
Connection for details.  
The input voltage to the projector must be capable of 100 – 240 VAC. See also 
Section 6 – Specifications for complete details on all power requirements. 
(4) Located on the bottom of the projector are 3 adjustable feet. You can raise or 
lower...

Page 27

Section 3: Operation 
 
Christie DS+60 User’s Manual     3-3  
(6) & (11) The two IR sensors located on the projector receive transmissions from the 
IR remote from up to 100 feet away. It is important to keep the transmission path to 
these sensors unobstructed for uninterrupted communications with the projector. The 
front IR sensor is located next to the projector’s nameplate and the rear IR sensor is 
located just below the input panel. 
(13) & (14) Located on the right hand side of the projector are...

Page 28

Section 3: Operation 
3-4   Christie DS+60 User’s Manual  
The IR remote keypad controls the projector by way of wireless communications from 
a battery-powered infrared (IR) transmitter. Use the IR remote keypad the same way 
you would use a remote keypad supplied with a TV or VCR. When making key 
presses, direct the keypad either toward the screen or toward the front or rear of the 
projector. One of the two IR sensors on the projector will detect the signals and relay 
the commands for internal...

Page 29

Section 3: Operation 
 
Christie DS+60 User’s Manual     3-5  
 
You can convert the IR remote into a wired remote keypad using the cable provided 
with the projector. Connect one end into the remote and the other to the mini stereo 
connector on the input panel labeled 
REMOTE. The wired remote is recommended 
when: 
• the built-in keypad is inaccessible 
• the lighting conditions are unsuitable for proper IR transmission 
NOTE: Leave the batteries in the wired remote for the laser key (
) to work....

Page 30

Section 3: Operation 
3-6   Christie DS+60 User’s Manual  
Table 3.1. Auto Setup  
What an “Auto Setup” Does 
OPTIMIZES: SETS TO DEFAULT: 
Pixel Tracking  Contrast 
Pixel Phase  Brightness 
Size and Blanking  Auto Input Level (off) 
Vertical Stretch  Detail (if video source) 
Position Filter 
Input Levels   Luma Delay 
NOTE: You must have an unlocked channel present to use Auto Setup.  
Channel 
Press 
C han nel to select a specific source setup (channel) defined and stored in projector 
memory. Once you...
Start reading Christie Digital Systems Ds+60 Users Manual

Related Manuals for Christie Digital Systems Ds+60 Users Manual

All Christie Digital Systems manuals