Christie Digital Systems Ds+4k, 8k, Dlv1400-dx, Mirage S+2k, 4k, 8k Users Manual

Section 2: Installation and Setup 
 
  
 User’s Manual     2-17. 
Regardless of how it is assigned, once a projector has a valid and unique address it 
will respond to commands sent to this address. To determine the projector’s current IP 
address, consult the Status or Communications menus. 
Refer to Section 3 for further information about setting up and using a projector 
connected via Ethernet. 
Log on to www.christiedigital.com for detailed information on ChristieNET. 
 
General Purpose Input Output...

Section 3 
Operation  
 
 User’s Manual     3-1 
 
This section explains how to effectively operate the projector once it has been 
installed. It is recommended that you read this section and familiarize yourself with 
the components and the available menu options before you begin using your projector 
for the first time. 
 
 
Figure 3.1. Projector Basics 
  
The built-in keypad is located at the back of the projector, beside the input panel. Use 
it similarly to the IR remote to control the projector. A...

Section 3: Operation 
3-2   
  User’s Manual      
The projector is built with a motorized lens mount that allows for easy lens control 
and adjustment. This includes such functions as adjusting vertical and horizontal 
offsets, zoom and focus. The lens mount can be fitted with any one of the available 
optional lenses – see Section 6 - Specifications.  
• Zoom and Focus – There are two internal lens motors that allow for quick 
motorized adjustment of zoom and focus. Adjust zoom to fit the displayed...

Section 3: Operation 
 
  
 User’s Manual     3-3. 
 
 
 Laser radiation is emitted from the laser diode in the remote. Do not look 
directly into the beam of the remote.
 
 
The projector is typically controlled using one of the following keypads: 
• Built-in Keypad located at the back of the projector  
• Remote Keypad for tethered or tetherless control up to 100 feet away 
(includes cable for use as a wired remote) 
While each of the keypads provides complete control of the projector, they differ...

Section 3: Operation 
3-4   
  User’s Manual      
 
 
 
* These are toggle keys, which require you to press and hold or press twice or 
press and use the up/down arrow keys. NOTE: To turn the OSD off you must 
press 
OSD and . 
Figure 3.3. Remote Keypad  

Section 3: Operation 
 
  
 User’s Manual     3-5. 
 
You can convert the IR remote into a wired remote keypad using the cable provided 
with the projector. Connect one end into the remote and the other to the mini stereo 
connector on the input panel labeled as 
REMOTE. The wired remote is recommended 
when: 
• the built-in keypad is inaccessible 
• the lighting conditions are unsuitable for proper IR transmission 
 
NOTE: Leave the batteries in the wired remote for the laser key (
) to work.  
 
Keep...

Section 3: Operation 
3-6   
  User’s Manual      
 
Table 3.1. Auto Setup  
What an “Auto Setup” Does 
OPTIMIZES: SETS TO DEFAULT: 
Pixel Tracking  Contrast 
Pixel Phase  Brightness 
Size and Blanking  Auto Input Level (off) 
Vertical Stretch  Detail (if video source) 
Position Filter 
Input Levels   Luma Delay 
NOTE: You must have an unlocked channel present to use Auto Setup.  
Channel 
Press 
C han nel to select a specific source setup (channel) defined and stored in projector 
memory. Once you enter...

Section 3: Operation 
 
  
 User’s Manual     3-7. 
Input 6 
Press 
Input  6 to display from the INPUT 6  interface module installed in the Option 2 slot. 
NOTE: If you have the optional Dual SD/HD-SDI Module installed and there are two 
inputs connected here, the second input (B) is considered 
INPUT 8. If you are using the 
built-in keypad or the remote keypad, press 
INPUT 6 to access INPUT 8 as follows: 
• While displaying from 
INPUT 6, press Input  5 again. This switches to INPUT 8. 
• While...

Section 3: Operation 
3-8   
  User’s Manual      
 
OSD (On-screen display)  
Press 
OSD  to hide the projector’s menu system during use. To see the menus 
again, do one of the following: 
• Press and hold
 OSD for two seconds 
• Press and release 
OSD followed immediately by  
• Press 
OSDOSD 
Invisible menus are fully functional, enabling “hidden” access to numbered features 
and image adjustments by entering the corresponding sequence of keypresses on the 
keypad. 
NOTES: 1) With OSD “on”, you can...