Česká Zbrojovka Cz 85 Instruction Manual

							CZ 85  -  INSTRUCTION MANUAL 24 ILLUSTRATION AND LIST OF PARTS   
						

							CZ 85  -  INSTRUCTION MANUAL 25 1 Frame * 
2 Slide Stop* 
3 Slide Stop Spring 
4 Slide Stop Spring Pin 
5 Trigger * 
6 Trigger Pin 
7 Trigger Bar * 
8 Trigger Spring 
9 Pin (3x) 
10 Ejector * 
11 Sear * 
12 Sear Spring 
13 Sear Pin * 
14 Firing Pin Block Lever * 
15 Firing Pin Block Lever Spring * 
16 Hammer * 
17 Disconnector * 
18 Hammer Pin 
19 Hammer Pin Retaining Peg 
20 Main Spring Strut 
21 Main Spring 
22 Main Spring Plug * 
23 Main Spring Plug Pin 
24 Magazine Brake * 
25 Magazine Brake Pin 
26 Grip Panel - Left * 
27 Grip Panel - Right * 
28 Grip Panel Screw (2x) 
29 Safety - Left * 
30 Safety Detent Plunger - Left * 
31 Safety Detent Plunger Spring (2x) * 
32 Magazine Catch * 
33 Magazine Catch Spring 34 Trigger Bar Spring 
35 Magazine Catch Spring Screw 
36 Magazine Body * 
37 Magazine Base 
38 Magazine Base Lock 
39 Magazine Spring * 
40 Follower * 
41 Recoil Spring 
42 Recoil Spring Guide 
43 Barrel * 
44 Slide with Barrel Bushing * 
45 Front Sight 
46 Front Sight Pin 
47 Loaded Chamber Indicator * 
48 Loaded Chamber Indicator Spring * 
49 Loaded Chamber Indicator Nut * 
50 Extractor * 
51 Extractor Pin 
52 Extractor Spring 
53 Rear Sight 
54 Firing Pin * 
55 Firing Pin Spring 
56 Firing Pin Stop * 
57 a) Firing Pin Roll Pin ø3 * 
b) Firing Pin Roll Pin ø2 * 
58 Firing Pin Block Stop * 
59 Firing Pin Block Stop Spring * 
60 Hammer Decocking Lever Controller * 
61 Decocking Lever * 
62 Decocking Lever Spring * 
63 Safety - Right * 
64 Safety Detent Plunger - Right * 
65 Slide Stop - Right * 
66 Trigger Overtravel Adjusting Screw * 
 
Comments: 
The parts marked * differ according to versions, or as case may be in some 
versions are entirely missing. 
 
 
 
The Company, reserves the right to make any changes it thinks necessary to improve its 
models or to meet any requirements of manufacturing or commercial nature.  
						

							CZ 85  -  INSTRUCTION MANUAL 26 TROUBLESHOOTING, CAUSES AND REMEDIES 
 
If your pistol is properly used and maintained, malfunctions will rarely occur. 
However, if such a situation does occur, please observe the following instructions. 
CAUTION - If a malfunction occurs, the possibility of unintentional discharge is 
substantially increased. For this reason, carefully observe the Safety Instructions 
already mentioned above. Keep the pistol pointed in a safe direction, do not turn 
the pistol against your body or anyone else’s! Do not place your hands in front of 
the barrel! 
If you use your pistol for self-defense, or in law enforcement, please acquire 
so-called dummy cartridges and practice fast clearing of malfunctions as 
described below. 
 
Malfunction Possible Cause Remedy A round has not been 
fed into the chamber or 
the slide has not fully 
locked with the barrel. Magazine is not fully 
inserted or is damaged. 
The pistol or cartridges are 
fouled (dirty) or too heavily 
greased. Insert magazine properly or 
change magazine. 
Clean the pistol and 
cartridges and wipe them dry 
or as case may be slightly 
lubricate. Misfire Defective cartridge 
 
 
 
Firing pin hole fouled (dirty) 
or unproper lubrication 
agent used under low 
temperature conditions. Pull the trigger again. If 
a discharge is not initiated, 
follow the Safety Instructions 
according to point 19. 
Disassemble and clean the 
firing pin or use a low 
temperature lubricant. A shot sounds weak 
combined with failure to 
eject the cartridge 
case. The primer has been 
activated but no powder 
load was inside the 
cartridge case. Unload the pistol and check 
that the bullet is not lodged in 
the barrel. A subsequent shot 
could cause damage to the 
barrel. The spent case has not 
been ejected. Cartridge chamber, 
extractor or ammunition 
dirty, or unsuitable lubricant 
in low temperature 
environment. Clean and wipe the pistol dry 
or lubricate lightly with a 
suitable agent. Use new and 
clean ammunition. If you cannot clear away any malfunction in the manner described above, 
entrust the pistol to a competent gunsmith for inspection and repair.  
						

							CZ 85  -  INSTRUCTION MANUAL 27 TECHNICAL SPECIFICATIONS 
 
Model CZ 85 
CZ 85 B 
CZ 85 BD CZ 85 COMBAT Caliber 9 mm Luger 
9 x 21 
.40 S&W 9 mm Luger Overall length [mm] 206 206 Height [mm] 138 138 Width  [mm] 38 38 Weight with empty magazine [g] 1000 1000 Barrel length [mm] 120 120 Sight radius [mm] 155 170 Magazine capacity 9 mm Luger 16 * 16 *  9 x 21 16 * -  .40 S&W 10 * - * To some countries, the CZ 85 pistols are supplied with a reduced magazine 
capacity in compliance with local laws. 
 
 
LIST OF ILLUSTRATIONS 
 
1. The names of basic parts 
2. Slide release from its rear lock-up position by its cocking and releasing 
3. Slide release from its rear lock-up position by depressing slide stop 
4. Shifting the safety to the SAFETY-ON position 
5. Release of the hammer in the version equipped with the manual safety 
6. Release of the hammer in the version equipped with no manual safety 
7. Positioning of the slide during disassembly 
8. Slide stop removal using the magazine base to facilitate this operation 
9. Firing pin disassembly