Casio Xj 360 Dlp Users Guide

31
Using the Setup Menu

Signal Settings 
J Noise Filter
This sub-menu provides a choice of noise filter levels to remove digital noise from the 
projected image when RGB is selected as the input source. Note that the noise filter may not 
be able to remove certain types of digital noise.
zThis setting is possible only when RGB is selected as the input source. The setting is 
saved for the RGB input source only.
zTurning off the projector automatically returns this sub-menu to its initial default setting...

Using the Setup Menu
32

Screen Settings 
J Aspect Ratio
This sub-menu lets you select the aspect ratio (ratio between the vertical and horizontal 
dimensions) of the projected image.
Input Source Specific Menu Items 
Setting Explanations
4:3: Sets the aspect ratio of the projected image to 4:3 (same as a standard TV 
screen). This setting is normally used when S-VIDEO or VIDEO is selected as 
the input source.
16:9: Sets the aspect ratio of the projected image to 16:9 (same as a movie screen 
or...

33
Using the Setup Menu

Screen Settings 
J Resize Image to Fit
When RGB is selected as the input source and the video resolution of the connected 
computer is anything other than XGA (1024 ×
 768 pixels), “Resize Image To Fit” automatically 
enlarges or reduces the input image so it matches the video resolution of the projector and 
fills the entire screen.
Input Source Specific Menu Items
Setting Explanations
On: When the input signal from the computer connected to the projector is not an 
XGA signal,...

Using the Setup Menu
34

Screen Settings 
J Projection Mode
Use this sub-menu to specify whether projection will be from the front of the screen or the 
back of the screen.
Input Source Specific Menu Items
Setting Explanations
Front: For projection from the front of the screen. 
Rear: For projection from the back of the screen. This setting flips the front projected 
image horizontally.
Setting Storage
A single setting is stored, which is applied to all input sources.

Screen Settings 
J Ceiling Mount...

35
Using the Setup Menu
zTurning on “Ceiling Mount” automatically turns off “Detailed Settings  J Low-noise Mode” 
(page 36). Note that the setting for “Low-noise Mode” remains “Off ” even if you turn 
“Ceiling Mount” back off again.
z The “Low-noise Mode” setting cannot be changed while “Ceiling Mount” is turned on.
z Unplug the AC power cord from the power outlet if you do not plan to use it for a long 
time.
z If you do not unplug the AC power cord when “Ceiling Mount” is turned on, the cooling 
fan...

Using the Setup Menu
36

Detailed Settings 
J Po i n t e r
This sub-menu lets you specify the type of pointer that appears first when you press the 
[POINTER/SELECT] key.
Input Source Specific Menu Items
Setting Storage
A single setting is stored, which is applied to all input sources.

Detailed Settings 
J Low-noise Mode
The low-noise mode reduces the luminosity of the projection lamp and the speed of the 
cooling fan, allowing quieter projector operation.
Input Source Specific Menu Items
Setting...

37
Using the Setup Menu

Detailed Settings 
J Power On Password, Change Password
This sub-menu lets you turn the power on password on and off.
While the password is turned on, projector operation is impossible unless the correct password 
is entered. 
For more information about the power on password, see “Password Feature” on page 52.
Input Source Specific Menu Items 
Setting Explanation
On: Turns on the power on password, which requires input of a password to turn on 
the projector.
Off: Turns off the...

Using the Setup Menu
38
Using the Password Input Dialog Box
The password input dialog box will appear when any one of the following occurs.
zWhen you turn on the projector while the password is turned on.
zWhen you turn the password on or off.
zWhen you change the password.
When this dialog box is shown, perform a remote controller key operation for each of the 
password input positions. The following explains how to input numbers.
zThe cursor is flashing at the first (leftmost) input position.
zThe...

39
Using the Setup Menu
5.Use the [S] and [T] keys to turn the power on password on or off.
6.Press the [ENTER] key.
To change the power on password
1.Perform steps 1 through 4 under “Basic Setup Menu Operations” on 
page 19. Select the “Detailed Settings” main menu, and then select 
the “Change Password” sub-menu item.
2.Press the [ENTER] key.
zThis displays a password input dialog box.
3.Input the current password.
zThe initial factory default password is: [S][X][T][W][S][T][W][X].
zFor information...

Using the Setup Menu
40

Detailed Settings 
J Advanced Settings 1 
J Auto Input Detect
This sub-menu lets you specify whether auto detect of the input source should be performed 
whenever the projector is turned on (page 5).
Input Source Specific Menu Items
Setting Explanations
On: Turns on auto detection of the input source whenever the projector is turned on.
Off: Turns off auto detection of the input source whenever the projector is turned on.
Setting Storage
A single setting is stored, which is...