Casio Ravine 3 Manual

30
Getting Started with Your Phone
2. Insert your finger in the groove  and pull up  
on the battery cover in the direction of the 
arrow . 
3. Remove the battery by pulling the tab up. 
4. Carefully press the memory card into  
the memory card slot until it locks  
into place. 
5. Install the battery and replace the battery cover ensuring that you 
slide the Battery Cover Lock to the LOCK position. 
For information on how to install the battery and the battery cover, refer to 
steps 3 through 6 of...

31
Getting Started with Your Phone
1.  Slide the Battery Cover Lock to the FREE  
position in the direction of the arrow 
shown in the figure to the right.
2. Insert your finger in the groove  and pull up  
on the battery cover in the direction of the 
arrow . 
3. Remove the battery by pulling the tab up.
4. Gently press the memory card inward, until  
it pops out. Remove the memory card.  

32
Getting Started with Your Phone
5. Install the battery and replace the battery cover, as previously 
instructed, ensuring that you slide the Battery Cover Lock to the 
LOCK position. 
Connecting to the Headset Jack
You can connect a compatible device equipped with a standard 
2.5mm plug to your handset for safe, convenient, hands-free 
conversations.
1.  To open the Headset Jack cover,  
insert your fingertip into the notch and 
open the cover.
2. Plug the connector into the Headset 
Jack. 
Warning !...

33
Quick Access to Convenient Features
Vibrate Mode
Vibrate Mode mutes key tones and activates an alert for an incoming 
call or message. 
To activate and deactivate Vibrate Mode:
1.  To activate Vibrate Mode from idle mode, press and hold .
2. To deactivate Vibrate Mode, press and hold  again.
Mute Function
If you activate the mute function during a call, the person you are 
speaking with cannot hear you or any sounds from your handset. 
However, you are still able to hear them. To activate Mute: 
1....

34
Quick Access to Convenient Features
Speakerphone
To activate and deactivate the speakerphone:
1.  To activate speakerphone from idle mode or during a call, press 
the Speakerphone/Flashlight Key .
2. To deactivate, press the Speakerphone/Flashlight Key  again. 
Flashlight
To activate and deactivate the flashlight:
1.  To activate from idle mode, press and hold the Speakerphone/
Flashlight Key . 
2. To deactivate, press and hold the Speakerphone/Flashlight Key  
again. 
Voice Dictation 
The voice...

35
Quick Access to Convenient Features
Motion Detection
Using the Motion Detection function, you can control your handset just 
by shaking it. 
By default, the Motion Detection function is off. To use the Motion 
Detection function: 
1.  From idle mode, press the Center Select Key [MENU], select 
Settings & Tools, then press the Center Select Key [OK]. Press 
 Phone Settings.
2. Select Motion Detection, then press the Center Select Key [OK]. 
3. Select one of the following settings, then press the...

36
Entering and Editing Information
Text Input
You can input and edit your Banner, Schedule, Contacts, and 
Messages.
To perform the Text Input operation described in this chapter with 
your handset, open the text entry screen following the steps below to 
create a new Text Message: 
1.  From idle mode, press the Left Soft Key [Message], select New 
Message and press the Center Select Key [OK]. 
2. Press  TXT Message. 
3. Enter the phone number or email address of the recipient, then 
press the Center...

37
Entering and Editing Information
Voice Commands: Press and hold to activate the Voice Dictation 
mode. Speak into the handset microphone while pressing and 
holding this key. The spoken phrases will be converted into text 
and entered into the text field. (Only when entering text into the 
Text or Subject field of a message, or into the Notepad)
Text Input Modes
There are six modes for entering text, numbers, symbols, and 
punctuation. 
Using Abc (Multi-tap) Text Input
To enter words in this mode,...

38
Entering and Editing Information
2. Press    .
3. Press  to complete the word and add a space.
4. Press     
 	       .
  “Call the office.” is displayed.
NOTES
After you have finished entering a word, if the word displayed 
is not the one you want, press the Next Key  to display 
additional word choices. 
Pressing  after pressing  to input a period displays 
other punctuation and symbols.  •
•
Adding Words to the T9 Database
If a word is not in the T9 database, add it by using Abc...

39
Entering and Editing Information
Using Symbol Text Input
To insert symbols or punctuation, follow these steps from the text 
entry screen: 
1.  Press the Left Soft Key, select Symbols, then press the Center 
Select Key [OK].
2. Press the Right Soft Key [Next] to view the next 12 symbols or Left 
Soft Key [Prev] to view the previous 12 symbols.
3. Select the symbol you want to insert using the Directional Key, then 
press the Center Select Key [OK] to select it. 
Using Palabra Mode Text Input
Palabra...