Casio Projector XJ-V10X User Manual

11
Connect the projector to a power outlet and to an input source device.
Use the provided power cord to plug the projector into a power outlet.
Use an RGB cable to connect to the RGB output terminal of a computer or other input source.
Use an HDMI cable to connect to the HDMI output terminal of a computer, video equipment, or 
other input source. Be sure to use a High Speed HDMI cable for connection.
The XJ-F Series models have two HDMI input terminals, which means you can have two external 
HDMI...

12
Projector operations are performed using the remote controller that comes with it. Point the remote 
controller signal emitter at one of the signal receivers on the projector as you perform remote 
controller key operations. The maximum range of the remote controller signal is approximately 
5 meters (16.4 feet) (between signal emitter and receiver).
Important!To avoid running down the batteries, store the remote control unit so its keys are not pressed 
inadvertently.
Remote Controller
Remote...

13
To load remote controller batteries
Important!Be sure to use alkaline batteries only.
To replace remote controller batteries
Open the battery cover on the back of the remote controller, replace the old batteries with new ones, 
and then close the battery cover.
*CautionRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
1.Open the battery cover on the back 
of the remote controller.2.Load two new batteries into the 
case, making sure...

14
Operating the Projector
Unless specifically noted otherwise, the operations in this section are performed using the remote 
controller. If both the projector and the remote controller have the same key, either one can be used to 
perform the corresponding operation.
The tables below show the input sources that can be selected for each projector model.
XJ-V Series
XJ-F Series
*Network models only
Selecting the Input Source (INPUT)
Input Source NameOutput Projection Image (and Audio)
Computer
(RGB or...

15
To select the input source
1.Press the [INPUT] key.
2.On the “Input” dialog box that appears, use the [INPUT], [] and [] keys to 
select the input source you want and then press the [ENTER] key.
If you do not press the [ENTER] key, the projector will automatically apply the currently 
selected input source after about three seconds.
The name of the input source you selected will appear in the upper right corner of the 
projection screen for a few seconds.
The message “No signal input” will appear...

16
To use manual keystone correction (KEYSTONE)
Use the [KEYSTONE +] and [KEYSTONE –] keys to adjust 
keystone correction manually.
The projector has a keystone correction feature that detects 
when it is at a vertical angle to the screen and performs 
keystone correction automatically. Use the above to make 
adjustment manually when auto correction produces results 
that are not what you want.
NoteIf there is no menu, dialog box, or anything else displayed on the projection screen with an 
XJ-F Series...

17
To momentarily blank the image and mute the audio (BLANK)
1.Press the [BLANK] key.
This blanks the screen by displaying the blank screen image specified by the Setup Menu 
“Blank Screen” setting (page 28) and mutes the audio.
2.To resume normal image and sound, press the [BLANK] key (or [ESC] key).
To freeze an image (FREEZE)
Press the [FREEZE] key to freeze the current input source image. To return to the real-time input 
source image, press the [FREEZE] key again or press the [ESC] key.
To auto...

18
Description of Each Setting
NoteFor details about how the aspect ratio setting affects the projected image, see “Aspect Ratio 
Setting and Projection Image” (page 78).
When projecting while “True” is selected as the aspect ratio setting for an RGB signal with a 
resolution that is less than SVGA, the image is enlarged to SVGA and projected.
You can also change the aspect ratio using the Setup Menu “Screen Settings 3 Aspect 
Ratio” setting (page 28).
Important!Note that enlarging or reducing the...

19
To adjust image brightness (FUNC)
1.Press the [FUNC] key. On the menu that appears, select “Brightness” and then 
press the [ENTER] key.
2.On the brightness adjustment screen that appears, use the [] and [] keys to 
adjust brightness.
3.To hide the window, press the [ESC] key.
NoteThe above operation is for fine adjusting image brightness without affecting light brightness. 
For information about changing light brightness, see “Light Control” (page 21).
To change the color mode (FUNC)
1.Press the...

20
Use the procedure below to adjust the volume level of the projector’s speaker output, and output from 
the AUDIO OUT terminal. If your projector does not have a built-in speaker, only AUDIO OUT terminal 
output is affected.
To adjust the volume level
1.Press the [VOLUME +] or [VOLUME –] key.
This causes the “Volume” screen to appear on the projected image.
2.Press the [VOLUME +] key to increase the volume, or the [VOLUME –] key to 
lower the volume.
3.After the setting is the way you want, press the...