Casio Projector XJ-V100W User Manual
Have a look at the manual Casio Projector XJ-V100W User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 338 Casio manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
61 Connecting the projector to a computer with a USB cable* enables projection of the computer’s screen contents. This supports projection of screen contents of even small computers that have only a USB port, but no RGB, HDMI, or other type of video output terminal. *To use the USB Display function, connect the computer to the projector’s USB-B port. Minimum Computer System Requirements Supported Operating Systems Windows XP SP3, Windows Vista SP1 (32bit), Windows 7 SP1 (32bit, 64bit), Windows 8/8.1 (64bit), Windows 10, or Mac OS (10.6, 10.7, 10.8, 10.9) Note, however, that functions may be limited by the operating system being used. For the latest information about operating environments, visit the CASIO website. USB Type A port (USB 2.0 or USB 3.0) equipped. Important!Log into Windows with admin privileges to use the USB display function. You will not be able to use USB display if you are logged into Windows with a non-admin account. The operation you need to perform the first time you connect to a computer to project its display contents (described below) depends on whether the computer is running Windows or Mac OS. After that, use the procedure under “To project computer screen contents over a USB connection after the first time” (page 65), which is the same for any operating system. Perform one of the procedures below, depending on your computer’s operating system. Projecting with the USB Display Function USB Display Function Overview Projecting Computer Screen Contents Over a USB Connection
62 To project Windows computer screen contents over a USB connection for the first time 1.Press the [INPUT] key. This will display the “Input” dialog box. 2.Use the [] and [] keys to select “USB Display” and then press the [ENTER] key. This will cause the “USB Display” standby screen to be projected. 3.While your computer is running, use a commercially available USB cable to connect the projector’s USB-B port (Micro USB B type) to your computer’s USB port. The location of the USB-B port of this projector is indicated by “*2” in the illustration under “Connecting Projector Cables” (page 11). This will mount the projector onto your computer as a virtual CD-ROM drive, which is represented by a “USB_DISPLAY” drive icon on your computer’s desktop. Also, CASIO USB Display will start up automatically and display a licensing agreement dialog box. 4.On the licensing agreement dialog box, select “I agree” and then click [OK]. This will display a window like the one shown below on your computer. At the same time, projection of the computer’s screen contents will start. NoteIf CASIO USB Display does not start up automatically, use Explorer to navigate to the “USB_DISPLAY” drive. Right-click the drive and then click “Auto Play” on the menu that appears. For information about the types of operations that can be performed at this point, see “Supported Operations during Projection over a USB connection” (page 64). Add-on Driver Software for Windows With Windows, use of some functions of the CASIO USB Display requires installation of the driver software shown in the table below. The driver software is the same as that used for Network Connection. You can download it from the Network Connection download page at the CASIO website (http://www.casio-intl.com/support/). To use this function:Install this driver software: Extended screen output function VDD driver (for Windows XP and Windows Vista)
63 To project Mac OS computer screen contents over a USB connection for the first time 1.Press the [INPUT] key. This will display the “Input” dialog box. 2.Use the [] and [] keys to select “USB Display” and then press the [ENTER] key. This will cause the “USB Display” standby screen to be projected. 3.While your computer is running, use a commercially available USB cable to connect the projector’s USB-B port to your computer’s USB port. The location of the USB-B port of this projector is indicated by “*2” in the illustration under “Connecting Projector Cables” (page 11). This will cause a drive icon named “USB_DISPLAY” to appear on your computer screen. 4.Double-click the “USB_DISPLAY” drive icon to open it. 5.Double-click “MAC_USB_Display_V2.pkg” and follow the instructions that appear on the display to install the application. A message prompting you to restart your computer will appear after installation is complete. Restart your computer. After the restart is complete, you will see a CASIO USB Display icon in the Dock. 6.In the Dock, click the CASIO USB Display icon. Also, CASIO USB Display will start up and display a licensing agreement dialog box. 7.On the licensing agreement dialog box, select “I agree” and then click [OK]. This will display a window like the one shown below on your computer. At the same time, projection of the computer’s screen contents will start. For information about the types of operations that can be performed at this point, see “Supported Operations during Projection over a USB connection” (page 64). Add-on Driver Software for Mac OS With Mac OS, use of some parts of the CASIO USB Display requires installation of the driver software shown in the table below. The driver software is the same as that used for Network Connection. You can download it from the Network Connection download page at the CASIO website (http://www.casio-intl.com/support/). To use this function:Install this driver software: Audio output function Sound flower Extended desktop output function Syphon-virtual-screen
64 Supported Operations during Projection over a USB connection The operations described in the table below are supported on the CASIO USB Display window during projection. To do this:Perform this operation: Start (resume) computer screen projection Click . Freeze computer screen projection Click . Stop computer screen projection and project the USB display standby screenClick . Start audio output from a computer* 1Click . On the menu that appears, select “Audio Out” so there is a check mark next to it. Mute audio output from a computer* 1Click . On the menu that appears, select “Audio Out” to remove the check mark next to it. Output the computer’s main screen on the projection screenClick . On the menu that appears, select “Select the Projection Screen” 3 “Main Screen”. Output the computer’s extended screen on the projection screen* 1*2Click . On the menu that appears, select “Select the Projection Screen” 3 “Extended Screen”. Minimize the CASIO USB Display window Click . Exit the CASIO USB Display window (1) Click . Or you could click and then click “Exit” on the menu that appears. (2) On the confirmation dialog box that appears, click the [OK] button. This stops computer screen projection and projects the “USB Display” standby screen. Display CASIO USB Display version information Click . On the menu that appears, select “About”. *1 With Mac, installation of driver software is required to enable these functions. See “Add-on Driver Software for Mac OS” (page 63). *2 This operation is disabled under Mac OS 10.6. With Windows XP and Windows Vista, installation of driver software is required to enable these functions. See “Add-on Driver Software for Windows” (page 62).
65 To project computer screen contents over a USB connection after the first time 1.Turn on and start up the projector and computer. 2.Press the [INPUT] key. This will display the “Input” dialog box. 3.Use the [] and [] keys to select “USB Display” and then press the [ENTER] key. This will cause the “USB Display” standby screen to be projected. 4.Use a USB cable to connect the projector’s USB-B port to your computer’s USB port. The CASIO USB Display will startup automatically on the computer and start projection of the computer screen contents. NoteIf the above operation does not cause CASIO USB Display to start up automatically, perform either of the operations below on your computer, depending on its operating system. Windows: Use Explorer to navigate to the “USB_DISPLAY” drive. Right-click the drive and then click “Auto Play” on the menu that appears. Mac OS: In the Dock, click the CASIO USB Display icon.
66 You can connect a CASIO graphing calculator to the Data Projector using a USB cable and project the calculator’s screen image with the Data Projector. USB connection of the following CASIO graphing calculators is supported. ClassPad II (fx-CP400) ClassPad 330 PLUS fx-CG series fx-9860G series fx-9860GII series fx-9750GII GRAPH 95/85/85 SD/75/75+/35+ To project the screen image of a graphing calculator 1.While the projector is turned on, connect the USB cable that comes with the graphing calculator to the projector’s USB-A port and the graphing calculator’s USB port. 2.On the projector, press the [INPUT] key. This will display the “Input” dialog box. 3.Use the [] and [] keys to select “CASIO USB Tool” and then press the [ENTER] key. 4.On the graphing calculator, perform the operation required for projection. For details about this operation, refer to the use documentation that comes with your calculator. Important!If the calculator does not operate properly after you connect it to the Data Projector, try disconnecting the USB cable from the calculator and then reconnecting it. If this does not correct the problem, disconnect the USB cable from both the Data Projector and the calculator. Turn the Data Projector off and then back on again, and then re-connect the calculator. Projecting the Screen Image of a Graphing Calculator
67 Cleaning the Projector Make it a habit to clean the projector at regular intervals as described in this section. Before cleaning the projector, be sure to unplug it from the power outlet and make sure it is cooled down completely. Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping. Never use benzene, alcohol, thinner, or any other volatile agent for cleaning. Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like those for eyeglasses or camera lenses. When cleaning the lens, do not apply undue force and take care to avoid damaging the lens. Dust and dirt tend to collect around the intake vents. Because of this, you should use a vacuum cleaner to clean away accumulated dust and dirt periodically (about once a month) as shown below. Important!Continued use of the projector after dust has accumulated around the intake vents can cause overheating of internal components and lead to malfunction. Certain operating conditions also can cause dirt and dust to accumulate around the projector’s exhaust vents. If this happens, use the same procedure as that described above to clean the exhaust vents. Cleaning the Projector Exterior Cleaning the Lens Cleaning Vents
68 Troubleshooting The POWER/STANDBY indicator and STATUS indicator change to show the current status of the projector as described in the tables below. POWER/STANDBY indicator STATUS indicator NoteThe POWER/STANDBY and STATUS indicators both light amber immediately after the projector is plugged into a power outlet. Indicators When the indicator is doing this:It means this about the projector: Lit red Connected to a power source, but turned off (standby mode) Flashing green Warming up after being turned on Lit green Power on, operation normal Flashing red Internal process in progress immediately after power off When the indicator is doing this:It means this about the projector: Lit green “On” selected for the “Light Control” setting Lit (or flashing) red Error Lit (or flashing) amber Error
69 Warning messages and indicators let you know what the problem is when a projector error occurs. When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug the AC power cord while the fan is still operating, an error may occur when you plug the AC power cord back in. Press the [ESC] key to clear the warning message. Error Indicators and Warning Messages Indicator/Error MessageDescription and Required Action POWER : Green steady The projector’s internal temperature is very high. Perform the following steps. Check for any blocking of the projector’s intake vents and exhaust vents, and make sure that there is sufficient space around the projector. See “Setup Precautions” (page 10). If there is dust accumulated around the intake vents and/or exhaust vents, turn off the projector and remove it. See “Cleaning the Projector” (page 67). STATUS : – (Green steady when “On” is selected for the “Light Control” setting.) Message : Internal temperature is too high. Check projector air vents for blockage. POWER : Green steady 3 Red steadyPower has turned off automatically due to internal overheating. Perform the following steps. Check for any blocking of the projector’s intake vents and exhaust vents, and make sure that there is sufficient space around the projector. See “Setup Precautions” (page 10). If there is dust accumulated around the intake vents and/or exhaust vents, remove it. See “Cleaning the Projector” (page 67). If there is no problem with the projector’s vents, confirm that the POWER/ STANDBY indicator is lit red (without flashing), and then turn power back on again. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. STATUS : – Message : Internal temperature is too high. The projector will turn off. POWER : Red steady Power has turned off automatically due to a fan problem. Confirm that the POWER/STANDBY indicator is lit red (without flashing) and that the fan has stopped. After checking the POWER/STANDBY indicator, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn projector power back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. STATUS : Amber flashing (0.5-second interval) POWER : Red steady Power has turned off automatically due to a system problem. After confirming that the POWER/STANDBY indicator is lit red (without flashing), disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn the projector back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. STATUS : – POWER : Red steady The projector was turned off automatically due to some problem that was probably caused by external digital noise or some other reason. Confirm that the POWER/STANDBY indicator is lit red (without flashing). After checking the POWER/STANDBY indicator, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn projector power back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. STATUS : Red steady Message : –
70 Check the following items whenever you experience any problem with the projector. POWER : Red steady The projector was turned off automatically because the light source unit turned off or did not turn on. After confirming that the POWER/STANDBY indicator is lit red (without flashing), unplug the power cord. Wait for a short while and then plug it back in and turn on the projector again. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. STATUS : Red flashing (0.5-second interval) Message : – POWER : Red steady Power has turned off automatically due to a projector memory error. Confirm that the POWER/STANDBY indicator is lit red (without flashing). After checking the POWER/STANDBY indicator, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn projector power back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. STATUS : Red flashing (2-second or 1-second interval) Message : – Projector Troubleshooting ProblemCause and Recommended Action Power does not turn on.If the POWER/STANDBY indicator is not lit, the AC power cord is not connected correctly. Connect the AC power cord correctly. If the POWER/STANDBY indicator is lit red and the STATUS indicator is lit (or flashing) red or amber, it means some type of error has occurred. See “Error Indicators and Warning Messages” (page 69). No image is projected or the projected image is abnormal.The computer or video device connected to the projector is not turned on or it is not outputting a video signal. Make sure the connected computer or video device is turned on, and perform the required operation on it to output a video signal. The correct output source is not selected on the projector. On the projector, select the correct input source that corresponds to the connected device. Images may not project correctly when you have the component output terminal of a video device connected to the COMPUTER terminal of the projector. Image color or display is very abnormal.The wrong option (“Component” or “RGB”) may be selected for the “Input Settings COMPUTER Terminal” setting on the setup menu. The image will not be projected correctly if “Component” is selected while the projector’s COMPUTER terminal is connected to the RGB output terminal of a computer, or if “RGB” is selected while the projector’s COMPUTER terminal is connected to the component video output terminal of a video device. On the setup menu, select “Auto” for the “Input Settings COMPUTER Terminal” setting. See page 28. I can’t understand messages or menus because they are the wrong language.Perform the following operation to select the language you want. See page 29. 1. Press the [MENU] key to display the setup menu. 2. If the input signal is HDMI (PC), press [] four times and then press the [ENTER] key. If the input signal is not HDMI (PC), press [] five times and then press the [ENTER] key. 3. Press [] twice and then press the [ENTER] key to display the language selection menu. 4. Use the [] and [] keys to move the highlighting to the language you want to select and then press the [ENTER] key. 5. Press the [MENU] key to exit the setup menu. Indicator/Error MessageDescription and Required Action