Casio Projector XJ-V100W User Manual

							11
Connect the projector to a power outlet and to an input source device.
Use the provided power cord to plug the projector into a power outlet.
Use an RGB cable to connect to the RGB output terminal of a computer or other input source.
Use an HDMI cable to connect to the HDMI output terminal of a computer, video equipment, or 
other input source. Be sure to use a High Speed HDMI cable for connection.
The XJ-F Series models have two HDMI input terminals, which means you can have two external 
HDMI devices connected at the same time.
Connect to the composite output or S-Video output of the video device. For details, see 
“Connecting to a Composite Video Output or S-Video Output (XJ-F Series Only)” (page 74).
NoteFor more information about component video connection, see “Connecting to a Component 
Video Output” on page 73.
For information about how to connect for RS-232C control of the projector, see “Projector 
RS-232C Control” (page 82).
For information about how to connect in order to update the projector firmware or to transfer 
user logo data, see “Updating Firmware and Transferring a User Logo” (page 76).
Connecting Projector Cables
*1 This port can be used to supply power (up to 5V DC 2A) to external equipment. For details, see 
“Supplying Power to External Equipment (XJ-F Series Only)” (page 75).
With the XJ-F20XN, XJ-F200WN, and XJ-F210WN projectors (network models), a USB flash drive 
(page 41), a CASIO calculator (page 66), or a separately available wireless adapter (refer to the 
separate “Network Function Guide”) can be connected to this port as an input source for 
projection.
*2 This port is equipped on the XJ-F20XN, XJ-F200WN, XJ-F210WN (network models) only.
It is used when accessing projector internal memory from a computer and when projecting 
computer screen contents from the projector over a USB connection. For details, see “To copy files 
from a computer to projector internal memory” (page 37) and “Projecting with the USB Display 
Function” (page 61).

Some of the terminals shown in the illustration are not equipped on the XJ-F10X and XJ-F100W.
XJ-V Series XJ-F Series
*1*2 
						

							12
Projector operations are performed using the remote controller that comes with it. Point the remote 
controller signal emitter at one of the signal receivers on the projector as you perform remote 
controller key operations. The maximum range of the remote controller signal is approximately 
5 meters (16.4 feet) (between signal emitter and receiver).
Important!To avoid running down the batteries, store the remote control unit so its keys are not pressed 
inadvertently.
Remote Controller
Remote control signal emitter
[P] key
Turns power on or off.
[ESC] key
Press to exit the currently displayed menu or to cancel an 
operation.
Cursor keys (///), [ENTER] key
Use the cursor keys to move between menu items, and to 
change setting values. Press the [ENTER] key to select a menu 
item or to execute a function.
Each of these keys has a specific fixed function. For details, 
see the sections that describe key operations in “Operating 
the Projector” (pages 14 through 35). For information about 
the [MENU] key, for example, see “Using the Setup Menu 
(MENU)” (page 26).
These keys are used with network models only. They are 
mainly used for File Viewer (page 36) projection operations.





 
						

							13
To load remote controller batteries
Important!Be sure to use alkaline batteries only.
To replace remote controller batteries
Open the battery cover on the back of the remote controller, replace the old batteries with new ones, 
and then close the battery cover.
*CautionRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
1.Open the battery cover on the back 
of the remote controller.2.Load two new batteries into the 
case, making sure that their positive 
(+) and negative (–) ends are facing 
correctly.
3.Close the battery cover on the back of the remote controller. 
						

							14
Operating the Projector
Unless specifically noted otherwise, the operations in this section are performed using the remote 
controller. If both the projector and the remote controller have the same key, either one can be used to 
perform the corresponding operation.
The tables below show the input sources that can be selected for each projector model.
XJ-V Series
XJ-F Series
*Network models only
Selecting the Input Source (INPUT)
Input Source NameOutput Projection Image (and Audio)
Computer
(RGB or Component)Images and audio from a computer or video device connected to the projector’s 
COMPUTER terminal and AUDIO IN terminal.
HDMI Images and audio from a computer or video device connected to the projector’s 
HDMI terminal.
Input Source NameOutput Projection Image (and Audio)
Computer
(RGB or Component)Images and audio from a computer or video device connected to the projector’s 
COMPUTER terminal and AUDIO IN terminal.
S-Video Images and audio from a video device connected to the projector’s S-VIDEO terminal 
and AUDIO IN R/L terminals.
Video Images and audio from a video device connected to the projector’s VIDEO terminal 
and AUDIO IN R/L terminals.
HDMI1 Images and audio from a computer or video device connected to the projector’s 
HDMI 1 terminal.
HDMI2 Images and audio from a computer or video device connected to the projector’s 
HDMI 2 terminal.
File Viewer*Images (and audio in the case of a movie file) contained in the following types of files 
located in projector internal memory or on a memory device connected to the 
projector’s USB-A port: image files, movie files, presentation files, PDF files.
CASIO USB Tool*Screen contents of a CASIO calculator or electronic dictionary connected to the 
projector’s USB-A port.
Network*Screen contents and audio of a computer connected to the projector via wireless LAN 
or wired LAN.
USB Display*Screen contents and audio of a computer connected to the projector’s USB-B port. 
						

							15
To select the input source
1.Press the [INPUT] key.
2.On the “Input” dialog box that appears, use the [INPUT], [] and [] keys to 
select the input source you want and then press the [ENTER] key.
If you do not press the [ENTER] key, the projector will automatically apply the currently 
selected input source after about three seconds.
The name of the input source you selected will appear in the upper right corner of the 
projection screen for a few seconds.
The message “No signal input” will appear if no input signal can be detected.
NoteFor more information about the operation required to select “Network”, “USB Display”, “File 
Viewer”, or “CASIO USB Tool” as the input source and perform projection, refer to the 
following.
Depending on the projector model, its video resolution will be fixed at XGA (1024 × 768 pixels) or 
WXGA (1280 × 800 pixels). Images may appear coarse, text and other figures may be difficult to read 
or a moire pattern may appear when the input signal from a computer does not match the projector’s 
video resolution. If this happens, try doing the following.
Change the computer’s output resolution setting so it matches the projector’s video resolution.
For information about the video resolution of your projector, see “Specifications” in the Setup 
Guide. See the user documentation that comes with your computer for details about changing its 
settings.
Change the “Aspect Ratio” setting to “True” (Applies only to models that support WXGA video 
resolution). With the “True” setting, the projector projects the input signal at its actual size (1 input 
source dot equal to one projector output pixel dot).
For information about configuring the Aspect Ratio setting, see “To change the aspect ratio of the 
projected image (ASPECT)” (page 17).Network: Separate Network Function Guide
USB Display: “Projecting with the USB Display Function” (page 61)
File Viewer: “Projecting with File Viewer” (page 36)
CASIO USB Tool: “Projecting the Screen Image of a Graphing Calculator” (page 66)
Resolution 
						

							16
To use manual keystone correction (KEYSTONE)
Use the [KEYSTONE +] and [KEYSTONE –] keys to adjust 
keystone correction manually.
The projector has a keystone correction feature that detects 
when it is at a vertical angle to the screen and performs 
keystone correction automatically. Use the above to make 
adjustment manually when auto correction produces results 
that are not what you want.
NoteIf there is no menu, dialog box, or anything else displayed on the projection screen with an 
XJ-F Series projector, you can also use the projector’s [] and [] keys to perform manual 
keystone correction.
To zoom an image (D-ZOOM)
1.Press the [D-ZOOM +] key.
This will enlarge the center of the projected image one step.
2.To zoom in on the center of the projected image more, press the [D-ZOOM +] 
key again. To zoom out, press the [D-ZOOM –] key.
Each press of [D-ZOOM +] zooms in (increases the zoom factor), while [D-ZOOM –] zooms 
out. Holding down either key continuously scrolls the zoom factor.
3.While an image is zoomed, use the [], [], [
], and [
] keys to scroll the view 
to other parts of the image.
4.To exit the zoom operation, press the [ESC] key.
Output Image Operations 
						

							17
To momentarily blank the image and mute the audio (BLANK)
1.Press the [BLANK] key.
This blanks the screen by displaying the blank screen image specified by the Setup Menu 
“Blank Screen” setting (page 28) and mutes the audio.
2.To resume normal image and sound, press the [BLANK] key (or [ESC] key).
To freeze an image (FREEZE)
Press the [FREEZE] key to freeze the current input source image. To return to the real-time input 
source image, press the [FREEZE] key again or press the [ESC] key.
To auto adjust an image (AUTO)
Press the [AUTO] key.
Pressing the [AUTO] key automatically adjusts the frequency and phase in accordance with the 
input signal, which can reduce flickering and other projected image problems.
This operation is supported while the input source is Computer (RGB).
To change the aspect ratio of the projected image (ASPECT)
Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.
Available settings depend on your projector model as shown below.
XJ-V100W/XJ-V110W/XJ-F100W/XJ-F200WN/XJ-F210WN
Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as 
shown below.
*XJ-F100W/XJ-F200WN/XJ-F210WN only
XJ-V10X/XJ-F10X/XJ-F20XN
Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as 
shown below.
*XJ-F10X/XJ-F20XN only
Input SourcePressing the [ASPECT] key will cycle through these settings:
RGB, HDMI(PC) Normal  Full  16:9  4:3  True
Video*, S-Video*, Component, HDMI(DTV) Normal  16:9  16:10  4:3  Letter Box
Input SourcePressing the [ASPECT] key will toggle between these settings:
RGB, HDMI(PC) Normal  Full  16:9  16:10
Video*, S-Video*, Component, HDMI(DTV) Normal  16:9  16:10  4:3 
						

							18
Description of Each Setting
NoteFor details about how the aspect ratio setting affects the projected image, see “Aspect Ratio 
Setting and Projection Image” (page 78).
When projecting while “True” is selected as the aspect ratio setting for an RGB signal with a 
resolution that is less than SVGA, the image is enlarged to SVGA and projected.
You can also change the aspect ratio using the Setup Menu “Screen Settings 3 Aspect 
Ratio” setting (page 28).
Important!Note that enlarging or reducing the size of an image using the [ASPECT] key for commercial 
purposes or public presentation may infringe on the legally protected copyright of the 
copyright holder of the original material. Normal: Projects at the projector’s maximum possible size while maintaining the input signal aspect 
ratio.
Full: Projects at the projector’s maximum possible size by enlarging or reducing the input signal.
16:9: This setting specifies a 16:9 aspect ratio, which is the same as a movie screen, high-definition 
TV, etc. Using this setting when the input signal is a 16:9 image that has been squeezed to a 
4:3 image causes the image to be displayed with its normal 16:9 aspect ratio.
16:10: This setting specifies a 16:10 aspect ratio. Use this setting to adjust the image for projection 
onto a 16:10 aspect ratio screen.
4:3: Regardless of the input signal aspect ratio, the image is always resized to an aspect ratio of 
4:3 for projection.
True: Projects the input signal at its actual size (1 input source dot equal to one projector output 
pixel dot) in the center of the projector’s projection screen. If the input signal resolution 
exceeds the projector’s output resolution, the excess is cut off.
Letter Box: This will resize the image horizontally to 1280 dots and project 800 vertical dots of the 
center of the image, maintaining the aspect ratio of the input signal. 
						

							19
To adjust image brightness (FUNC)
1.Press the [FUNC] key. On the menu that appears, select “Brightness” and then 
press the [ENTER] key.
2.On the brightness adjustment screen that appears, use the [] and [] keys to 
adjust brightness.
3.To hide the window, press the [ESC] key.
NoteThe above operation is for fine adjusting image brightness without affecting light brightness. 
For information about changing light brightness, see “Light Control” (page 21).
To change the color mode (FUNC)
1.Press the [FUNC] key. On the menu that appears, select “Color Mode” and then 
press the [ENTER] key.
This displays the color mode selection window. The currently selected color mode is the one 
whose button is selected (filled in).
2.Use the [] and [] keys to move the highlighting to the color mode you want to 
select, and then press the [ENTER] key.
This will select the button next to the highlighted color mode name.
For details on what each color mode does, see “Image Adjustment 1 3 Color Mode” (page 
27).
3.To hide the window, press the [ESC] key.
Important!The color mode cannot be selected in the following cases.
• When “Off” is selected for the “Light Control” setting (page 21) 
						

							20
Use the procedure below to adjust the volume level of the projector’s speaker output, and output from 
the AUDIO OUT terminal. If your projector does not have a built-in speaker, only AUDIO OUT terminal 
output is affected.
To adjust the volume level
1.Press the [VOLUME +] or [VOLUME –] key.
This causes the “Volume” screen to appear on the projected image.
2.Press the [VOLUME +] key to increase the volume, or the [VOLUME –] key to 
lower the volume.
3.After the setting is the way you want, press the [ESC] key.
To mute the audio
1.Press the [VOLUME +] or [VOLUME –] key to display the “Volume” screen.
2.Press the [ENTER] key.
This stops output from the speaker.
3.To restore the audio, press the [VOLUME +] or [VOLUME –] key.
Adjusting the Volume Level (VOLUME)