Casio Projector XJ-V1 User Manual

							41
Command List
zOnly the following functions are supported while the projector is turned off. Do not try to send any 
other command to the projector.
zInput of a valid signal must be in progress in order to use a command to turn on blank screen or 
change the aspect ratio.
R: Read enabled   W: Write enabled zPower on/off: Read
zPower on: Write
zGet light time: Read
FunctionCommand 
NameRWSetting Range
Power On/Off:PWR RW 0: Off, 1: On
Input Switching: 0:Switches the input source to the 
COMPUTER terminal and changes the 
COMPUTER terminal setting to RGB.
1:Switches the input source to COMPUTER 
terminal and changes the COMPUTER 
terminal setting to component.
6:Switches the input source to COMPUTER 
terminal and changes the COMPUTER 
terminal setting to Auto.
7:Switches the input source to HDMI.SRC RW 0: RGB, 1: Component,
6: Auto (RGB/Component),
7: HDMI
Blank Screen: Switches the blank screen on or off. BLK RW 0: Off, 1: On
Volume:Specifies a value to adjust the volume level. This 
setting is applied to the input source signal that is 
currently being projected by the projector.VOL RW 0 to 30
Color Mode: Selects the color mode. PST RW 1: Graphics, 2: Theater, 
3: Standard, 4: Blackboard, 
5: Natural
Aspect Ratio: Specifies the aspect ratio. ARZ RW 0: Normal, 1: 16:9, 4: Full, 
7: 16:10 (when RGB or HDMI 
(PC) is selected for input)
1: 16:9, 2: Normal, 6: 4:3, 
7: 16:10 (when Component or 
HDMI (DTV) is selected for 
input)
Get Light Time:Gets the light time from the projector. LMP R 0- Unit: Hours
Eco Mode:Enter Eco Mode. PMD RW 0: Off (Bright), 1: Off (Normal), 
3: On (Manual 1), 
4: On (Manual 2), 
5: On (Manual 3), 
6: On (Manual 4), 
7: On (Manual 5)
Freeze:Switches freeze on or off. FRZ RW 0: Off, 1: On
Keystone Correction: 
Specifies the keystone correction setting as a value that 
corresponds to the typical Setup Menu “Keystone 
Correction” settings below.
0: Keystone Correction –60
60: Keystone Correction 0
120: Keystone Correction +60
Example:65 here, specifies a setting equivalent to 
Keystone Correction +5.KST RW 0 to 120 
						

							42
Keystone Correction +: 
Raises the current keystone correction setting by 1.KSP W 0 to 120
Keystone Correction –: 
Lowers the current keystone correction setting by 1.KSM W 0 to 120
Key:Operation executed when a key is pressed. KEY W 1: S, 2: T, 3: W, 4: X, 
5: ENTER, 6: ESC, 10: FUNC, 
11: MENU, 12: POWER, 
13: AUTO, 14: INPUT, 
15: TIMER, 16: ASPECT, 
17: BLANK, 18: FREEZE, 
19: ECO, 20: KEYSTONE +, 
21: KEYSTONE –, 
22: D-ZOOM +, 
23: D-ZOOM –, 
24: VOLUME +, 
25: VOLUME –
Setup Type:Specifies how the projector is set up relative to 
screen for projection.
0:Projection to a screen in front of the 
projector*
1
1:Ceiling mounted projection from behind the 
screen*2
2:Projection from behind the screen*1
3:Ceiling mounted projection to a screen in 
front of the projector*2
POS RW 0 to 3
APO:Used to change the Auto Power Off setting (trigger time 
setting or Auto Power Off disable).APO RW 0: Off, 1: 5 minutes, 
2: 10 minutes, 3: 15 minutes, 
4: 20 minutes, 5: 30 minutes
Error:Reads the projector error status. STS R 0: Normal, 1: Fan error, 
2: Temperature error, 
7: Light error, 16: Other error
Volume +:Raises the current volume setting by 1. VLP W 0 to 30
Volume –:Lowers the current volume setting by 1. VLM W 0 to 30
Mute:Switches mute on or off. MUT RW 0: Off, 1: On
*1 Top of projector upwards
*2 Top of projector downwards
FunctionCommand 
NameRWSetting Range 
						

							
MA1504-B