Casio Projector XJ-M250 XJ-M255 User Manual
Here you can view all the pages of manual Casio Projector XJ-M250 XJ-M255 User Manual. The Casio manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 11
![Page 11
11
Entering the 3D Input Mode
1.Press the [INPUT] key to display the input source selection screen.
2.Select Computer (RGB), S-video, or Video as the input source.
3.Use the [T] and [S] keys to move the highlighting to “To 3D input mode” and
then press the [ENTER] key.
zThis enters the 3D input mode and closes the input source selection screen.
Important!zYou cannot select HDMI or USB as the input source in the 3D input mode. To use either of
these input sources, change the input source setting back to...](http://img.usermanuals.tech/thumb/16/98950/w300_projector_manual_6251_d-10.png "Page 11
11
Entering the 3D Input Mode
1.Press the [INPUT] key to display the input source selection screen.
2.Select Computer (RGB), S-video, or Video as the input source.
3.Use the [T] and [S] keys to move the highlighting to “To 3D input mode” and
then press the [ENTER] key.
zThis enters the 3D input mode and closes the input source selection screen.
Important!zYou cannot select HDMI or USB as the input source in the 3D input mode. To use either of
these input sources, change the input source setting back to...")
11 Entering the 3D Input Mode 1.Press the [INPUT] key to display the input source selection screen. 2.Select Computer (RGB), S-video, or Video as the input source. 3.Use the [T] and [S] keys to move the highlighting to “To 3D input mode” and then press the [ENTER] key. zThis enters the 3D input mode and closes the input source selection screen. Important!zYou cannot select HDMI or USB as the input source in the 3D input mode. To use either of these input sources, change the input source setting back to...
Page 12
12 You can perform the following operations while projecting an image. zImage brightness adjustment zColor mode selection zImage zooming zMomentary cut off of the input source image and projection of a black or blue screen, or a logo zImage freeze zPointer display in the projected image zAspect ratio switching Adjusting Image Brightness Note(for USB port model users) Use the setup menu (page 20) to adjust image brightness when the input source is an external device connected to the USB port. To adjust...
Page 13
![Page 13
13
Selecting the Color Mode
You can select from among various different color mode settings in accordance with image contents
and projection conditions.
Important!The color mode cannot be selected in the following cases.
zWhen “Off” is selected for the Eco Mode setting (page 18)
zWhen the projector is in the 3D input mode. See “3D Input Mode” (page 10).
To change the color mode
1.Press the [COLOR MODE] key.
zThis displays the color mode selection window. The currently selected color mode is the one...](http://img.usermanuals.tech/thumb/16/98950/w300_projector_manual_6251_d-12.png "Page 13
13
Selecting the Color Mode
You can select from among various different color mode settings in accordance with image contents
and projection conditions.
Important!The color mode cannot be selected in the following cases.
zWhen “Off” is selected for the Eco Mode setting (page 18)
zWhen the projector is in the 3D input mode. See “3D Input Mode” (page 10).
To change the color mode
1.Press the [COLOR MODE] key.
zThis displays the color mode selection window. The currently selected color mode is the one...")
13 Selecting the Color Mode You can select from among various different color mode settings in accordance with image contents and projection conditions. Important!The color mode cannot be selected in the following cases. zWhen “Off” is selected for the Eco Mode setting (page 18) zWhen the projector is in the 3D input mode. See “3D Input Mode” (page 10). To change the color mode 1.Press the [COLOR MODE] key. zThis displays the color mode selection window. The currently selected color mode is the one...
Page 14
![Page 14
14
Momentarily Cutting Off the Input Source Image
1.Press the [BLANK] key.
zThis temporarily cuts off the image from the input source and projects a black screen in its
place.
2.To resume projection of the image from the input source, press the [BLANK] key
(or [ESC] key).
NoteYou can specify projection of a black screen or blue screen, or a logo. For details, see “Blank
Screen” under “Screen Settings Main Menu” on page 32.
Freezing an Image
Pressing the [FREEZE] key freezes the projected image.
To...](http://img.usermanuals.tech/thumb/16/98950/w300_projector_manual_6251_d-13.png "Page 14
14
Momentarily Cutting Off the Input Source Image
1.Press the [BLANK] key.
zThis temporarily cuts off the image from the input source and projects a black screen in its
place.
2.To resume projection of the image from the input source, press the [BLANK] key
(or [ESC] key).
NoteYou can specify projection of a black screen or blue screen, or a logo. For details, see “Blank
Screen” under “Screen Settings Main Menu” on page 32.
Freezing an Image
Pressing the [FREEZE] key freezes the projected image.
To...")
14 Momentarily Cutting Off the Input Source Image 1.Press the [BLANK] key. zThis temporarily cuts off the image from the input source and projects a black screen in its place. 2.To resume projection of the image from the input source, press the [BLANK] key (or [ESC] key). NoteYou can specify projection of a black screen or blue screen, or a logo. For details, see “Blank Screen” under “Screen Settings Main Menu” on page 32. Freezing an Image Pressing the [FREEZE] key freezes the projected image. To...
Page 15
![Page 15
15
Displaying a Pointer in the Projected Image
You can select from among different pointer styles, including various arrow styles, for display in the
projected image. Pointers can be used during a presentation to indicate or highlight a specific part of
the image.
NoteDepending on the pointer style you are using, the pointer may not display properly when you are
using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE –] keys to
change the keystone correction value to zero.
To...](http://img.usermanuals.tech/thumb/16/98950/w300_projector_manual_6251_d-14.png "Page 15
15
Displaying a Pointer in the Projected Image
You can select from among different pointer styles, including various arrow styles, for display in the
projected image. Pointers can be used during a presentation to indicate or highlight a specific part of
the image.
NoteDepending on the pointer style you are using, the pointer may not display properly when you are
using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE –] keys to
change the keystone correction value to zero.
To...")
15 Displaying a Pointer in the Projected Image You can select from among different pointer styles, including various arrow styles, for display in the projected image. Pointers can be used during a presentation to indicate or highlight a specific part of the image. NoteDepending on the pointer style you are using, the pointer may not display properly when you are using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE –] keys to change the keystone correction value to zero. To...
Page 16
![Page 16
16
Changing the aspect ratio of the projected image
Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.
Available settings depend on your projector model as shown below. For details about the meaning of
each setting, see the “Aspect Ratio” setting under “Screen Settings Main Menu” on page 31.
XJ-M240/XJ-M245/XJ-M250/XJ-M255
Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as
shown below....](http://img.usermanuals.tech/thumb/16/98950/w300_projector_manual_6251_d-15.png "Page 16
16
Changing the aspect ratio of the projected image
Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.
Available settings depend on your projector model as shown below. For details about the meaning of
each setting, see the “Aspect Ratio” setting under “Screen Settings Main Menu” on page 31.
XJ-M240/XJ-M245/XJ-M250/XJ-M255
Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as
shown below....")
16 Changing the aspect ratio of the projected image Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image. Available settings depend on your projector model as shown below. For details about the meaning of each setting, see the “Aspect Ratio” setting under “Screen Settings Main Menu” on page 31. XJ-M240/XJ-M245/XJ-M250/XJ-M255 Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as shown below....
Page 17
![Page 17
17
You can use the remote controller keys to adjust the volume level of the audio that is output from the
projector’s speaker.
To adjust the volume level
1.Press the [VOLUME] key.
zThis causes the [Volume] screen to appear on the projected image.
2.Press the [X] key to increase the volume, or the [W] key to lower the volume.
3.After the setting is the way you want, press the [ESC] key.
zThis causes the [Volume] screen to disappear.
NoteYou also can use the setup menu to adjust the volume level. For...](http://img.usermanuals.tech/thumb/16/98950/w300_projector_manual_6251_d-16.png "Page 17
17
You can use the remote controller keys to adjust the volume level of the audio that is output from the
projector’s speaker.
To adjust the volume level
1.Press the [VOLUME] key.
zThis causes the [Volume] screen to appear on the projected image.
2.Press the [X] key to increase the volume, or the [W] key to lower the volume.
3.After the setting is the way you want, press the [ESC] key.
zThis causes the [Volume] screen to disappear.
NoteYou also can use the setup menu to adjust the volume level. For...")
17 You can use the remote controller keys to adjust the volume level of the audio that is output from the projector’s speaker. To adjust the volume level 1.Press the [VOLUME] key. zThis causes the [Volume] screen to appear on the projected image. 2.Press the [X] key to increase the volume, or the [W] key to lower the volume. 3.After the setting is the way you want, press the [ESC] key. zThis causes the [Volume] screen to disappear. NoteYou also can use the setup menu to adjust the volume level. For...
Page 18
18 The following three Eco Mode settings are available to specify whether priority should be given to low-power, low-noise operation or to projection brightness. Important!zWhile “On (Auto)” is selected as the Eco Mode setting, make sure that the brightness sensor on the top of the projector is not blocked by anything. zThe local environment and setup conditions affect the brightness sensor, so operation when “On (Auto)” is selected for the Eco Mode depends on these factors. To select the Eco Mode...
Page 19
![Page 19
19
NotezWhile “Off” is selected for the Eco Mode setting, you also can specify whether brightness or
color should be given emphasis. For details, see “Eco Off Mode” under “Image Adjustment 1
Main Menu” (page 29).
z(for USB port model users)
Use the setup menu (page 20) to select the Eco Mode when the input source is an external
device connected to the USB port.
Pressing the [FUNC] key displays the menu shown below.
You can use this menu to perform the operations described below.
zAdjust image...](http://img.usermanuals.tech/thumb/16/98950/w300_projector_manual_6251_d-18.png "Page 19
19
NotezWhile “Off” is selected for the Eco Mode setting, you also can specify whether brightness or
color should be given emphasis. For details, see “Eco Off Mode” under “Image Adjustment 1
Main Menu” (page 29).
z(for USB port model users)
Use the setup menu (page 20) to select the Eco Mode when the input source is an external
device connected to the USB port.
Pressing the [FUNC] key displays the menu shown below.
You can use this menu to perform the operations described below.
zAdjust image...")
19 NotezWhile “Off” is selected for the Eco Mode setting, you also can specify whether brightness or color should be given emphasis. For details, see “Eco Off Mode” under “Image Adjustment 1 Main Menu” (page 29). z(for USB port model users) Use the setup menu (page 20) to select the Eco Mode when the input source is an external device connected to the USB port. Pressing the [FUNC] key displays the menu shown below. You can use this menu to perform the operations described below. zAdjust image...
Page 20
![Page 20
20
Configuring Advanced Projector Settings
Your projector has a setup menu that you can use to configure advanced settings.
Displaying the Setup Menu
Pressing the [MENU] key displays the menu shown below in the center of the projection screen.
To exit the setup menu
Press the [MENU] key.
Configuring Setup Menu Settings
1.Press the [MENU] key to display the setup menu.
2.Use the [T] and [S] keys to select the main menu item you want by highlighting
it.
3.Press the [ENTER] key.
4.Use the [T] and [S] keys...](http://img.usermanuals.tech/thumb/16/98950/w300_projector_manual_6251_d-19.png "Page 20
20
Configuring Advanced Projector Settings
Your projector has a setup menu that you can use to configure advanced settings.
Displaying the Setup Menu
Pressing the [MENU] key displays the menu shown below in the center of the projection screen.
To exit the setup menu
Press the [MENU] key.
Configuring Setup Menu Settings
1.Press the [MENU] key to display the setup menu.
2.Use the [T] and [S] keys to select the main menu item you want by highlighting
it.
3.Press the [ENTER] key.
4.Use the [T] and [S] keys...")
20 Configuring Advanced Projector Settings Your projector has a setup menu that you can use to configure advanced settings. Displaying the Setup Menu Pressing the [MENU] key displays the menu shown below in the center of the projection screen. To exit the setup menu Press the [MENU] key. Configuring Setup Menu Settings 1.Press the [MENU] key to display the setup menu. 2.Use the [T] and [S] keys to select the main menu item you want by highlighting it. 3.Press the [ENTER] key. 4.Use the [T] and [S] keys...