Casio Projector XJ-H2650 User Manual

							41
Screen Settings Main Menu
Setting NameInputSetting UnitDescription
Keystone 
Correction
RCVHDUNSingle Use this sub-menu to perform vertical keystone correction of the 
projected image.
Aspect Ratio
RCVHDSource 
SpecificUse this sub-menu to select an aspect ratio setting for the projected 
image.
Input Source: RGB or HDMI (PC)
Normal*:
Projects at the projector’s maximum possible size while 
maintaining the input signal aspect ratio.
Full:
Projects at the projector’s maximum possible size by enlarging or 
reducing the input signal.
4:3 (XJ-H2600/XJ-H2650 only):
Regardless of the input signal aspect ratio, the image is always 
resized to an aspect ratio of 4:3 for projection.
True (XJ-H2600/XJ-H2650 only):
Projects the input signal at its actual size (1 input source dot equal 
to one projector output pixel dot) in the center of the projector’s 
projection screen. If the input signal resolution exceeds the 
projector’s output resolution, the excess is cut off.
Input Source: Video, S-video, Component or 
HDMI (DTV)
Normal*:
Projects at the projector’s maximum possible size while 
maintaining the input signal aspect ratio.
16:9 :
This setting specifies a 16:9 aspect ratio, which is the same as a 
movie screen, high-definition TV, etc. Using this setting when the 
input signal is a 16:9 image that has been squeezed to a 4:3 
image causes the image to be displayed with its normal 16:9 
aspect ratio.
4:3 (XJ-H2600/XJ-H2650 only):
Regardless of the input signal aspect ratio, the image is always 
resized to an aspect ratio of 4:3 for projection.
Letter Box (XJ-H2600/XJ-H2650 only):
This will resize the image horizontally to 1280 dots and project 
800 vertical dots of the center of the image, maintaining the 
aspect ratio of the input signal.
NotezWhen projecting while “True” is selected as the aspect ratio 
setting for an RGB signal with a resolution that is less than 
SVGA, the image is enlarged to SVGA and projected.
zFor details about projection screen display conditions for 
different aspect ratio settings, see “Aspect Ratio Setting 
and Projection Image” (page 60).
Important!Note that enlarging or reducing the size of an image for 
commercial purposes or public presentation may infringe on 
the legally protected copyright of the copyright holder of the 
original material. 
						

							42
Projection 
ModeRCVHDUNSingle Use this sub-menu to specify whether projection will be from the 
front of the screen or the back of the screen.
Front*:
Select this option to project from the front of the screen.
Rear:
Select this option to project from the back of the screen. This 
setting flips the front projected image horizontally.
Ceiling Mount
RCVHDUNSingle Use this sub-menu to configure the projector for use in an 
installation in which it is positioned upside down.
On:
Flips the projected image horizontally and vertically.
Off*:
Projects a normal image.
Startup Screen
RCVHDUNSingle Use this sub-menu to specify whether or not a startup screen should 
be projected whenever the projector is turned on.
Logo:
Select this option to project the projector’s built-in logo screen.
Custom Logo:
Select this option to project the custom logo registered with 
“Custom Logo Capture” (page 30).
None*:
Select this option when you do not want to project a startup 
screen.
No Signal 
Screen
RCVHDUNSingle Use this sub-menu to specify what should be projected when there 
is no input signal to the projector.
Blue*:
Select this option to project a blue screen.
Black:
Select this option to project a black screen.
Logo:
Select this option to project the projector’s built-in logo screen.
Custom Logo:
Select this option to project the custom logo registered with 
“Custom Logo Capture” (page 30).
Blank Screen
RCVHDUNSingle Use this sub-menu to specify what should be projected after the 
[BLANK] key is pressed.
Blue:
Select this option to project a blue screen.
Black*:
Select this option to project a black screen.
Logo:
Select this option to project the projector’s built-in logo screen.
Custom Logo:
Select this option to project the custom logo registered with 
“Custom Logo Capture” (page 30).
Setting NameInputSetting UnitDescription 
						

							43
Input Settings Main Menu
Restore Menu 
DefaultsRCVHDUNSource 
SpecificUse this sub-menu to return all of the sub-menu items on the Screen 
Settings main menu to their initial default settings.
zRestoring menu defaults when there is no input signal will restore 
defaults for the currently selected input source.
zNote that the “Keystone Correction”, “Projection Mode”, “Ceiling 
Mount”, “Startup Screen”, “No Signal Screen”, and “Blank 
Screen” settings are always returned to their initial defaults, 
regardless of the currently selected input source.
Setting NameInputSetting UnitDescription
COMPUTER1 
Terminal/
COMPUTER2 
Terminal
RCNSingle Use this sub-menu to specify manually the type of signal being input 
from the projector’s COMPUTER IN 1/COMPUTER IN 2 terminal.
Auto*:
Automatically detects the signal being input from the COMPUTER 
IN 1/COMPUTER IN 2 terminal and configures the appropriate 
input protocol.
RGB:
Select this option when a computer is connected to the 
COMPUTER IN 1/COMPUTER IN 2 terminal. For details about 
connecting a computer, see “Connecting the Analog RGB Output 
of a Computer to the Projector” (page 12).
Component:
Select this setting when the projector’s COMPUTER IN 1/
COMPUTER IN 2 terminal is connected to the component video 
output terminal of a video device using a commercially available 
component video cable. For information about connection, see 
“Connecting to a Video Device” (page 14).
NoteThe setting of this item cannot be changed while the projector 
is in the 3D input mode (“3D Input Mode”, page 17) or “On” is 
selected for the “Option Settings 2J Interactive Pointer” 
setting.
Video Signal/
S-Video Signal
VNSingle Use this sub-menu to specify manually the type of signal being input 
from the projector’s VIDEO terminal or S-VIDEO terminal.
Auto*:
Select this setting to have the projector switch the video signal 
system automatically in accordance with the input signal from the 
video device that is connected to the VIDEO terminal or S-VIDEO 
terminal.
NTSC / NTSC4.43 / PAL / PAL-M / PAL-N / PAL60 / SECAM:
Each setting selects the applicable video system. Use these 
settings when you want to specify only one specific video signal 
for the VIDEO terminal or S-VIDEO terminal.
Setting NameInputSetting UnitDescription 
						

							44
Option Settings 1 Main Menu
Signal Name 
IndicatorRCVHDUNSingle Use this sub-menu to specify whether or not the name of the 
currently selected signal source should be displayed in the projected 
image.
On*:
Select this option to turn on display of the name of the currently 
selected signal source in the projected image.
Off:
Select this option to turn off display of the signal source name.
Restore Menu 
Defaults
RCVHDUNSource 
SpecificUse this sub-menu to return all of the sub-menu items on the Input 
Settings main menu to their initial default settings.
zRestoring menu defaults when there is no input signal will restore 
defaults for the currently selected input source.
zNote that the “Signal Name Indicator” setting is always returned 
to its initial default, regardless of the currently selected input 
source.
Setting NameInputSetting UnitDescription
Auto Keystone 
Correction
RCVHDUNSingle Use this sub-menu to turn auto keystone correction on or off.
On*:
Select this option to turn on auto keystone correction.
Off:
Select this option to turn off auto keystone correction.
Auto Adjust
RNSource 
SpecificUse this sub-menu to select whether the projector should detect the 
RGB input signal type (resolution, frequency) and adjust the 
projection image accordingly (auto adjust).
1*:
Select this option to turn on auto adjust.
2:
Select this option to turn on auto adjust when a 1360 × 768 or 
1400 × 1050 signal is not projected correctly.
3:
Select this option to turn on auto adjust when a 1366 × 768 signal 
is not projected correctly.
Off:
Select this option to turn off auto adjust.
Eco Mode
RCVHDUNSingle See “Eco Mode (Power Saving, Low Noise)” (page 25).
Auto White 
Balance
RCVHDUNSingle Turns automatic white balance adjustment on or off.
On*:
White balance adjusted automatically. Can improve color 
reproduction.
Off:
White balance not adjusted automatically.
Setting NameInputSetting UnitDescription 
						

							45
Auto Power OffRCVHDUNSingle Auto Power Off lets you specify the amount of time of projector 
operation and input signal inactivity to be allowed before Auto Power 
Off is triggered to turn off projector power automatically. Auto Power 
Off can be disabled, if you want.
5 min, 10 min*, 15 min, 20 min, 30 min:
Time until Auto Power off is triggered.
Off:
Disables Auto Power Off.
Note(for USB port model users)
Auto Power Off is disabled whenever the projector is doing 
any one of the following.
– Projecting the Viewer initial screen
– Projecting the Wireless standby screen
– Using Wireless for a wireless LAN connection between 
the projector and a computer or other terminal
Password 
protection
RCVHDUNSingle See “Password Protection” on page 32.
Direct Power 
On
RCVHDUNSingle Use this sub-menu to turn Direct Power On on or off. See “Direct 
Power On” on page 29.
On:
Select this option to turn on Direct Power On.
Off*:
Select this option to turn off Direct Power On.
Language
RCVHDUNSingle Use this sub-menu to specify the language to use for messages, 
setup menus, etc.
English / French / German / Italian / Spanish / Swedish / 
Portuguese / Dutch / Norwegian / Polish / Finnish / Czech / Turkish / 
Russian / Chinese (Simplified) / Chinese (Traditional) / Korean / 
Japanese
Note(for USB port model users)
If you have Portuguese, Dutch, Norwegian, Polish, Finnish, 
Czech, Turkish, or Russian selected as the projector’s 
language, selecting an external device connected to the 
projector’s USB-A port as the input source will cause some 
menus and messages to be displayed in English.
Restore Menu 
Defaults
RCVHDUNSingle This sub-menu returns all of the sub-menu items on the Option 
Settings 1 main menu to their initial default settings.
zThe language setting and the password are not returned to their 
initial factory defaults.
zThe “Auto Adjust” item is returned to its initial default only when 
RGB input is selected for the input source. All of the other items 
are returned to their initial defaults regardless of the currently 
selected input source.
Setting NameInputSetting UnitDescription 
						

							46
Option Settings 2 Main Menu
Setting NameInputSetting UnitDescription
Pointer
RCVHDUNSingle Use this sub-menu to specify the type of pointer that appears first 
when you press the [POINTER] key.
Plug and Play
(USB port 
models only)
RCVHDUNSingle Use this sub-menu to turn plug-and-play on or off.
On*:
Select this option to turn on plug-and-play. This will allow the 
projector detect when an external USB device is connected and 
make that device the input source automatically.
Off:
Select this option to turn off plug-and-play.
NotezFor details about plug-and-play, see the “USB Function 
Guide”.
zRegardless of the setting of this item, plug-and-play is 
disabled while the projector is in the 3D input mode (“3D 
Input Mode”, page 17) or “On” is selected for the “Option 
Settings 2J Interactive Pointer” setting.
Audio Out
RCVHDUNSingle Specifies whether the input audio signal should be output from the 
projector’s built-in speaker or to the line output.
Speaker*:
Outputs the audio signal being input to the projector from the 
speaker.
Line:
Outputs the audio signal being input to the projector from the 
AUDIO OUT terminal.
High Altitude
RCVHDUNSingle Use this sub-menu to turn the high-altitude fan speed setting on or 
off in accordance with the altitude of the area where you are using 
the projector.
On:
Select this setting when using the projector in a high altitude 
(1,500 to 3,000 meters above sea level) area where air is thin. This 
setting increases cooling efficiency.
Off*:
Select this setting at normal altitudes (up to 1,500 meters).
Important!Do not use this projector at altitudes greater than 
3,000 meters above sea level.
Control Panel 
Lock
RCVHDUNSingle Use this sub-menu to disable (lock) and enable (unlock) the 
projector’s control panel.
On:
Select this setting to disable (lock) all projector key operations 
except for [P] (Power).
Off*:
Select this setting to enable (unlock) projector key operations.
Custom Logo 
Capture
RCVHDUSingle See “Custom Logo Capture” (page 30). 
						

							47
Standby RGB/
AudioRCVHDUNSingle Use this sub-menu to configure the projector for output of the video 
signal from the COMPUTER IN 1 terminal to the MONITOR OUT 
terminal, and output of the audio signal from the AUDIO IN 1 terminal 
to the AUDIO OUT terminal while the projector is in standby 
(projector off with power being supplied).
Output:
Select this setting to output video and audio signals while the 
projector is in standby.
No Output*:
Select this setting not to output video and audio signals while the 
projector is in standby.
NotezWhen “Output” is selected for this setting, audio is output 
from the AUDIO OUT terminal during standby, regardless of 
the projector’s current “Option Settings 2J Audio Out” 
setting.
zInput signals from the COMPUTER IN 2 terminal and 
AUDIO IN 2 terminal cannot be output from the MONITOR 
OUT terminal and AUDIO OUT terminal during projector 
standby.
Closed 
Caption
VNSingle Specifies whether to display closed captions when projecting a 
video signal that includes them.
Off*:
Closed captions not displayed.
CC1, CC2, CC3, CC4:
Indicates the current closed caption output setting (CC1, CC2, 
CC3, CC4).
NoteKeystone correction does not affect displayed closed caption 
text.
Interactive 
Pointer
RHSingle Enables/disables operation of the optionally available interactive 
pointer (YA-P10).
On:
Interactive pointer operation enabled.
Off*:
Interactive pointer operation disabled.
Important!Select “On” for this item only when using an interactive 
pointer. Select “Off” when you are not using it.
NoteRegardless of this setting, interactive pointer operation is 
always disabled when the projector is in the 3D input mode 
(page 17).
Restore Menu 
Defaults
RCVHDUNSingle This sub-menu returns all of the sub-menu items on the Option 
Settings 2 main menu to their initial default settings. Note, however, 
that a custom logo captured with “Custom Logo Capture” is not 
initialized.
Setting NameInputSetting UnitDescription 
						

							48
Wired LAN Settings Main Menu (USB Port Models Only)
USB Settings Main Menu (USB Port Models Only)
The USB Settings main menu is available only when there is an external device connected to the 
USB-A port of the projector. For details, see the “USB Function Guide” and “Wireless Function 
Guide”.
Setting NameInputSetting UnitDescription
Remote on
RCVHDUNSingle Specifies whether the projector can be turned on via wired LAN while 
the projector is in standby (projector off with power being supplied).
Enable:
Power on enabled.
Disable*:
Power on disabled.
Important!Performing an “Initialize Network Settings” operation or 
“Restore All Defaults” operation with the setup menu will 
cause this setting to change to “Disable”. If you are operating 
the projector using a wired LAN setting, be sure to change this 
setting back to “Enable” after initialization.
PJLink 
authentication
RCVHDUNSingle Enables and disables PJLink connection authentication.
Enable*:
PJLink connection authentication enabled.
Disable:
PJLink connection authentication disabled.
Wired LAN info
RCVHDUNSingle Displays the following information.
Projector name:
Name currently assigned to the projector.
MAC Address:
Fixed MAC address assigned to each individual projector.
IP Address:
Projector’s current IP address.
DHCP:
Projector’s current DHCP setting status (“Auto” or “Disable”).
The projector name, IP address, and DHCP settings can be 
configured using the projector System Admin page, which can be 
accessed on a computer connected by LAN to the projector. For 
details, see the “Wireless Function Guide”.
Initialize 
Network 
Settings
RCVHDUNSingle Returns all projector network settings (all settings on the System 
Admin page) to their initial defaults.
For detailed information about System Admin page settings, see the 
“System Admin Page Settings” section in the “Wireless Function 
Guide”. 
						

							49
Operational Info Main Menu
Restore All Defaults Main Menu
Setting NameInputSetting UnitDescription
Input Signal
RCVHDUNSource 
SpecificThis sub-menu item shows the currently selected input signal (RGB, 
Component, Video, S-video, HDMI(PC), or HDMI (DTV)). “- - - -” is 
indicated here when there is no input signal.
Signal Name
RCVHDUSource 
SpecificThis sub-menu item shows the signal name of the signal being input 
to the projector. For details about signal names, see “Signal Name” 
under “Supported Signals” (page 62).
Resolution
RHSource 
SpecificThis sub-menu item appears only when RGB is the input signal. It 
shows the number of vertical and horizontal pixels of resolution of 
the RGB or HDMI (PC) input signal.
Horizontal 
Frequency
RCVHDSource 
SpecificThis sub-menu item shows the horizontal frequency of the input 
signal.
Vertical 
Frequency
RCVHDSource 
SpecificThis sub-menu item shows the vertical frequency of the input signal.
Scan System
RCHDSource 
SpecificThis sub-menu item appears only when RGB, Component, 
HDMI (PC), or HDMI (DTV) is the input signal, and shows the scan 
system of the input signal. The scan system is interlace or 
non-interlace for an RGB or HDMI (PC) signal input, and interlace or 
progressive for a component or HDMI (DTV) signal input.
Light Time
RCVHDUNSingle This sub-menu item shows the cumulative number of hours the 
current light source unit has been used to date.
Setting NameInputSetting UnitDescription
Unit Operating 
Time
RCVHDUNSingle This sub-menu item shows the cumulative operating time of this unit. 
This time cannot be initialized.
Restore All 
Defaults
RCVHDUNSingle This sub-menu returns all sub-menu items on all main menus to their 
initial default settings. This operation can be performed regardless of 
the currently selected input source and regardless of whether or not 
a signal is currently being input. For details about this procedure, see 
“To restore all settings on the setup menu to their initial factory 
defaults” on page 37. 
						

							50
Cleaning the Projector
Periodically clean the projector exterior, lens, intake vents, and intake-exhaust vents on a regular 
basis.
Important!Before cleaning the projector, be sure to unplug it from the power outlet and make sure it is 
cooled down completely.
Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water 
and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping.
Never use benzene, alcohol, thinner, or any other volatile agent for cleaning.
Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like those for 
eyeglasses or camera lenses. When cleaning the lens, do not apply undue force and take care to avoid 
damaging the lens.
Dust and dirt tend to collect around the vents. Because of this, you should use a vacuum cleaner to 
clean away accumulated dust and dirt periodically as shown below.
Important!Continued use of the projector after dust has accumulated around the vents can cause 
overheating of internal components and lead to malfunction.
Cleaning the Projector Exterior
Cleaning the Lens
Cleaning the Vents