Casio Projector XJ-H2650 User Manual

21
Momentarily Blanking the Image and Muting the Audio
1.Press the [BLANK] key.
zThis temporarily blanks the image (projecting a black screen) and mutes the audio.
2.To resume normal image and sound, press the [BLANK] key (or [ESC] key).
NoteYou can specify projection of a black screen, a blue screen, a logo screen, or a custom logo 
screen. For details, see “Blank Screen” (page 42) under “Screen Settings Main Menu”.
Freezing an Image
Pressing the [FREEZE] key freezes the projected image.
To freeze the...

22
Displaying a Pointer in the Projected Image
You can select from among different pointer styles, including various arrow styles, for display in the 
projected image. Pointers can be used during a presentation to indicate or highlight a specific part of 
the image.
NoteDepending on the pointer style you are using, the pointer may not display properly when you are 
using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE –] keys to 
change the keystone correction value to zero.
To...

23
Changing the Aspect Ratio of the Projected Image
Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.
Available settings depend on your projector model as shown below. For details about the meaning of 
each setting, see “Aspect Ratio” (page 41) under “Screen Settings Main Menu”.
XJ-H2600/XJ-H2650
Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as 
shown below.
XJ-H1600/XJ-H1650/XJ-H1700/XJ-H1750/XJ-ST145/XJ-ST155...

24
You can use the remote controller keys to adjust the volume level of the audio that is output from the 
projector’s speaker or the AUDIO OUT terminal.
To adjust the volume level
1.Press the [VOLUME] key.
zThis causes the [Volume] screen to appear on the projected image.
2.Press the [X] key to increase the volume, or the [W] key to lower the volume.
3.After the setting is the way you want, press the [ESC] key.
zThis causes the [Volume] screen to disappear.
NoteYou also can use the setup menu to adjust...

25
The following three Eco Mode settings are available to specify whether priority should be given to 
low-power, low-noise operation or to projection brightness.
Important!zWhile “On (Auto)” is selected as the Eco Mode setting, make sure that the brightness sensor 
on the top of the projector is not blocked by anything.
zThe local environment and setup conditions affect the brightness sensor, so operation when 
“On (Auto)” is selected for the Eco Mode depends on these factors.
To select the Eco Mode...

26
NotezWhile “Off” is selected for the Eco Mode setting, you also can specify whether brightness or 
color should be given emphasis. For details, see “Eco Off Mode” (page 39) under “Image 
Adjustment 1 Main Menu”.
z(for USB port model users)
Use the setup menu (page 27) to select the Eco Mode when the input source is an external 
device connected to the USB-A port.
Pressing the [FUNC] key displays the menu shown below.
You can use this menu to perform the operations described below.
zAdjust image...

27
Configuring Advanced Projector Settings
Your projector has a setup menu that you can use to configure advanced settings.
Displaying the Setup Menu
Pressing the [MENU] key displays the menu shown below in the center of the projection screen.
To exit the setup menu
Press the [MENU] key.
Configuring Setup Menu Settings
1.Press the [MENU] key to display the setup menu.
2.Use the [T] and [S] keys to select the main menu item you want by highlighting 
it.
3.Press the [ENTER] key.
4.Use the [T] and [S] keys...

28
Basic Setup Menu Example
The procedure below shows how to configure the following three settings:
zImage Adjustment 1 J Contrast
zImage Adjustment 1 J Color Mode
zInput Settings J Signal Name Indicator
NotezThe setup menu items that you can change depend on whether or not an image signal is being 
input to the projector, and on the currently selected input source. Perform the procedure 
below after starting projection of an image from an input source in the normal input mode. See 
“3D Input Mode” on...

29
To configure the “Image Adjustment 1 J Color Mode” setting
5.Use the [T] key to select “Color Mode”.
6.Press the [ENTER] key.
zThis displays the color mode menu.
7.Use the [T] and [S] keys to select the color mode you want, and then press the 
[ENTER] key.
8.After selecting the color mode you want, press the [ESC] key.
To configure the “Input Settings J Signal Name Indicator” setting
9.Press the [ESC] key.
10.Use the [T] key to select “Input Settings”.
11.Press the [ENTER] key.
12.Use the [T] key to...

30
You can capture a projected screen and save it as image data in the projector’s built-in memory. 
Image data you save in projector memory is called a custom logo.
The following are ways you could use a custom logo.
– As a startup screen image that appears first whenever the projector is turned on
– As a default projection image whenever there is no input signal to the projector (No Signal Screen)
– As the screen projected whenever the [BLANK] key is pressed (Blank Screen)
Important!Note that using the...