Home > Casio > Projector > Casio Projector XJ-F20XN User Manual

Casio Projector XJ-F20XN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Casio Projector XJ-F20XN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 338 Casio manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							61
    Connecting the projector to a computer with a USB cable* enables projection of the computer’s 
    screen contents. This supports projection of screen contents of even small computers that have only a 
    USB port, but no RGB, HDMI, or other type of video output terminal.
    *To use the USB Display function, connect the computer to the projector’s USB-B port.
    Minimum Computer System Requirements
    Supported Operating Systems
    Windows XP SP3, Windows Vista SP1 (32bit), Windows 7 SP1 (32bit, 64bit), Windows 8/8.1 (64bit), 
    Windows 10, or Mac OS (10.6, 10.7, 10.8, 10.9)
    Note, however, that functions may be limited by the operating system being used. For the latest 
    information about operating environments, visit the CASIO website.
    USB Type A port (USB 2.0 or USB 3.0) equipped.
    Important!Log into Windows with admin privileges to use the USB display function. You will not be able 
    to use USB display if you are logged into Windows with a non-admin account.
    The operation you need to perform the first time you connect to a computer to project its display 
    contents (described below) depends on whether the computer is running Windows or Mac OS. After 
    that, use the procedure under “To project computer screen contents over a USB connection after the 
    first time” (page 65), which is the same for any operating system.
    Perform one of the procedures below, depending on your computer’s operating system.
    Projecting with the USB Display Function
    USB Display Function Overview
    Projecting Computer Screen Contents Over a USB Connection 
    						
    							62
    To project Windows computer screen contents over a USB 
    connection for the first time
    1.Press the [INPUT] key. This will display the “Input” dialog box.
    2.Use the [] and [] keys to select “USB Display” and then press the [ENTER] 
    key.
    This will cause the “USB Display” standby screen to be projected.
    3.While your computer is running, use a commercially available USB cable to 
    connect the projector’s USB-B port (Micro USB B type) to your computer’s USB 
    port.
    The location of the USB-B port of this projector is indicated by “*2” in the illustration under 
    “Connecting Projector Cables” (page 11).
    This will mount the projector onto your computer as a virtual CD-ROM drive, which is 
    represented by a “USB_DISPLAY” drive icon on your computer’s desktop.
    Also, CASIO USB Display will start up automatically and display a licensing agreement dialog 
    box.
    4.On the licensing agreement dialog box, select “I agree” and then click [OK].
    This will display a window like the one shown below on your computer. At the same time, 
    projection of the computer’s screen contents will start.
    NoteIf CASIO USB Display does not start up automatically, use Explorer to navigate to the 
    “USB_DISPLAY” drive. Right-click the drive and then click “Auto Play” on the menu that 
    appears.
    For information about the types of operations that can be performed at this point, see 
    “Supported Operations during Projection over a USB connection” (page 64).
    Add-on Driver Software for Windows
    With Windows, use of some functions of the CASIO USB Display requires installation of the driver 
    software shown in the table below. The driver software is the same as that used for Network 
    Connection. You can download it from the Network Connection download page at the CASIO website 
    (http://www.casio-intl.com/support/).
    To use this function:Install this driver software:
    Extended screen output function VDD driver (for Windows XP and Windows Vista) 
    						
    							63
    To project Mac OS computer screen contents over a USB 
    connection for the first time
    1.Press the [INPUT] key. This will display the “Input” dialog box.
    2.Use the [] and [] keys to select “USB Display” and then press the [ENTER] 
    key.
    This will cause the “USB Display” standby screen to be projected.
    3.While your computer is running, use a commercially available USB cable to 
    connect the projector’s USB-B port to your computer’s USB port.
    The location of the USB-B port of this projector is indicated by “*2” in the illustration under 
    “Connecting Projector Cables” (page 11).
    This will cause a drive icon named “USB_DISPLAY” to appear on your computer screen.
    4.Double-click the “USB_DISPLAY” drive icon to open it.
    5.Double-click “MAC_USB_Display_V2.pkg” and follow the instructions that 
    appear on the display to install the application.
    A message prompting you to restart your computer will appear after installation is complete. 
    Restart your computer. After the restart is complete, you will see a CASIO USB Display icon in 
    the Dock.
    6.In the Dock, click the CASIO USB Display icon.
    Also, CASIO USB Display will start up and display a licensing agreement dialog box.
    7.On the licensing agreement dialog box, select “I agree” and then click [OK].
    This will display a window like the one shown below on your computer. At the same time, 
    projection of the computer’s screen contents will start.
    For information about the types of operations that can be performed at this point, see 
    “Supported Operations during Projection over a USB connection” (page 64).
    Add-on Driver Software for Mac OS
    With Mac OS, use of some parts of the CASIO USB Display requires installation of the driver software 
    shown in the table below. The driver software is the same as that used for Network Connection. You 
    can download it from the Network Connection download page at the CASIO website 
    (http://www.casio-intl.com/support/).
    To use this function:Install this driver software:
    Audio output function Sound flower
    Extended desktop output function Syphon-virtual-screen 
    						
    							64
    Supported Operations during Projection over a USB connection
    The operations described in the table below are supported on the CASIO USB Display window during 
    projection.
    To do this:Perform this operation:
    Start (resume) computer screen projection
    Click .
    Freeze computer screen projection
    Click .
    Stop computer screen projection and project the USB 
    display standby screenClick .
    Start audio output from a computer*
    1Click  . On the menu that appears, select “Audio 
    Out” so there is a check mark next to it.
    Mute audio output from a computer*
    1Click  . On the menu that appears, select “Audio 
    Out” to remove the check mark next to it.
    Output the computer’s main screen on the projection 
    screenClick  . On the menu that appears, select “Select the 
    Projection Screen” 3 “Main Screen”.
    Output the computer’s extended screen on the 
    projection screen*
    1*2Click  . On the menu that appears, select “Select the 
    Projection Screen” 3 “Extended Screen”.
    Minimize the CASIO USB Display window Click  .
    Exit the CASIO USB Display window (1) Click  . Or you could click   and then click 
    “Exit” on the menu that appears.
    (2) On the confirmation dialog box that appears, click 
    the [OK] button.
    This stops computer screen projection and 
    projects the “USB Display” standby screen.
    Display CASIO USB Display version information Click  . On the menu that appears, select “About”.
    *1 With Mac, installation of driver software is required to enable these functions. See “Add-on Driver 
    Software for Mac OS” (page 63).
    *2 This operation is disabled under Mac OS 10.6. With Windows XP and Windows Vista, installation of 
    driver software is required to enable these functions. See “Add-on Driver Software for Windows” 
    (page 62). 
    						
    							65
    To project computer screen contents over a USB connection 
    after the first time
    1.Turn on and start up the projector and computer.
    2.Press the [INPUT] key. This will display the “Input” dialog box.
    3.Use the [] and [] keys to select “USB Display” and then press the [ENTER] 
    key.
    This will cause the “USB Display” standby screen to be projected.
    4.Use a USB cable to connect the projector’s USB-B port to your computer’s USB 
    port.
    The CASIO USB Display will startup automatically on the computer and start projection of the 
    computer screen contents.
    NoteIf the above operation does not cause CASIO USB Display to start up automatically, perform 
    either of the operations below on your computer, depending on its operating system.
    Windows:
    Use Explorer to navigate to the “USB_DISPLAY” drive. Right-click the drive and then click 
    “Auto Play” on the menu that appears.
    Mac OS:
    In the Dock, click the CASIO USB Display icon. 
    						
    							66
    You can connect a CASIO graphing calculator to the Data Projector using a USB cable and project the 
    calculator’s screen image with the Data Projector. USB connection of the following CASIO graphing 
    calculators is supported.
    ClassPad II (fx-CP400)
    ClassPad 330 PLUS
    fx-CG series
    fx-9860G series
    fx-9860GII series
    fx-9750GII
    GRAPH 95/85/85 SD/75/75+/35+
    To project the screen image of a graphing calculator
    1.While the projector is turned on, connect the USB cable that comes with the 
    graphing calculator to the projector’s USB-A port and the graphing calculator’s 
    USB port.
    2.On the projector, press the [INPUT] key. This will display the “Input” dialog box.
    3.Use the [] and [] keys to select “CASIO USB Tool” and then press the 
    [ENTER] key.
    4.On the graphing calculator, perform the operation required for projection.
    For details about this operation, refer to the use documentation that comes with your 
    calculator.
    Important!If the calculator does not operate properly after you connect it to the Data Projector, try 
    disconnecting the USB cable from the calculator and then reconnecting it. If this does not 
    correct the problem, disconnect the USB cable from both the Data Projector and the 
    calculator. Turn the Data Projector off and then back on again, and then re-connect the 
    calculator.
    Projecting the Screen Image of a Graphing Calculator 
    						
    							67
    Cleaning the Projector
    Make it a habit to clean the projector at regular intervals as described in this section. Before cleaning 
    the projector, be sure to unplug it from the power outlet and make sure it is cooled down completely.
    Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water 
    and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping.
    Never use benzene, alcohol, thinner, or any other volatile agent for cleaning.
    Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like those for 
    eyeglasses or camera lenses. When cleaning the lens, do not apply undue force and take care to avoid 
    damaging the lens.
    Dust and dirt tend to collect around the intake vents. Because of this, you should use a vacuum 
    cleaner to clean away accumulated dust and dirt periodically (about once a month) as shown below.
    Important!Continued use of the projector after dust has accumulated around the intake vents can cause 
    overheating of internal components and lead to malfunction.
    Certain operating conditions also can cause dirt and dust to accumulate around the 
    projector’s exhaust vents. If this happens, use the same procedure as that described above to 
    clean the exhaust vents.
    Cleaning the Projector Exterior
    Cleaning the Lens
    Cleaning Vents 
    						
    							68
    Troubleshooting
    The POWER/STANDBY indicator and STATUS indicator change to show the current status of the 
    projector as described in the tables below.
    POWER/STANDBY indicator
    STATUS indicator
    NoteThe POWER/STANDBY and STATUS indicators both light amber immediately after the 
    projector is plugged into a power outlet.
    Indicators
    When the indicator is doing this:It means this about the projector:
    Lit red Connected to a power source, but turned off (standby mode)
    Flashing green Warming up after being turned on
    Lit green Power on, operation normal
    Flashing red Internal process in progress immediately after power off
    When the indicator is doing this:It means this about the projector:
    Lit green “On” selected for the “Light Control” setting
    Lit (or flashing) red Error
    Lit (or flashing) amber Error 
    						
    							69
    Warning messages and indicators let you know what the problem is when a projector error occurs.
    When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug 
    the AC power cord while the fan is still operating, an error may occur when you plug the AC power 
    cord back in.
    Press the [ESC] key to clear the warning message.
    Error Indicators and Warning Messages
    Indicator/Error MessageDescription and Required Action
    POWER : Green steady The projector’s internal temperature is very high. Perform the following 
    steps.
    Check for any blocking of the projector’s intake vents and exhaust 
    vents, and make sure that there is sufficient space around the 
    projector. See 
    “Setup Precautions” (page 10).
    If there is dust accumulated around the intake vents and/or exhaust 
    vents, turn off the projector and remove it. See 
    “Cleaning the 
    Projector” (page 67). STATUS : –
    (Green steady when “On” 
    is selected for the “Light 
    Control” setting.)
    Message : Internal temperature is too 
    high. Check projector air 
    vents for blockage.
    POWER : Green steady 3
    Red steadyPower has turned off automatically due to internal overheating. Perform 
    the following steps.
    Check for any blocking of the projector’s intake vents and exhaust 
    vents, and make sure that there is sufficient space around the 
    projector. See 
    “Setup Precautions” (page 10).
    If there is dust accumulated around the intake vents and/or exhaust 
    vents, remove it. See 
    “Cleaning the Projector” (page 67).
    If there is no problem with the projector’s vents, confirm that the POWER/
    STANDBY indicator is lit red (without flashing), and then turn power back 
    on again. If the error occurs again when you turn power back on, contact 
    your retailer or nearest authorized CASIO Service Center. STATUS : –
    Message : Internal temperature is too 
    high. The projector will 
    turn off.
    POWER : Red steady Power has turned off automatically due to a fan problem. Confirm that the 
    POWER/STANDBY indicator is lit red (without flashing) and that the fan 
    has stopped. After checking the POWER/STANDBY indicator, disconnect 
    the power cord from the projector and wait for all of the projector’s 
    indicators to go out. Next, reconnect the power cord and turn projector 
    power back on.
    If the error occurs again when you turn power back on, contact your 
    retailer or nearest authorized CASIO Service Center. STATUS : Amber flashing
    (0.5-second interval)
    POWER : Red steady Power has turned off automatically due to a system problem. After 
    confirming that the POWER/STANDBY indicator is lit red (without 
    flashing), disconnect the power cord from the projector and wait for all of 
    the projector’s indicators to go out. Next, reconnect the power cord and 
    turn the projector back on.
    If the error occurs again when you turn power back on, contact your 
    retailer or nearest authorized CASIO Service Center. STATUS : –
    POWER : Red steady The projector was turned off automatically due to some problem that was 
    probably caused by external digital noise or some other reason. Confirm 
    that the POWER/STANDBY indicator is lit red (without flashing). After 
    checking the POWER/STANDBY indicator, disconnect the power cord 
    from the projector and wait for all of the projector’s indicators to go out. 
    Next, reconnect the power cord and turn projector power back on.
    If the error occurs again when you turn power back on, contact your 
    retailer or nearest authorized CASIO Service Center. STATUS : Red steady
    Message : – 
    						
    							70
    Check the following items whenever you experience any problem with the projector.
    POWER : Red steady The projector was turned off automatically because the light source unit 
    turned off or did not turn on. After confirming that the POWER/STANDBY 
    indicator is lit red (without flashing), unplug the power cord. Wait for a 
    short while and then plug it back in and turn on the projector again.
    If the error occurs again when you turn power back on, contact your 
    retailer or nearest authorized CASIO Service Center. STATUS : Red flashing
    (0.5-second interval)
    Message : –
    POWER : Red steady Power has turned off automatically due to a projector memory error. 
    Confirm that the POWER/STANDBY indicator is lit red (without flashing). 
    After checking the POWER/STANDBY indicator, disconnect the power 
    cord from the projector and wait for all of the projector’s indicators to go 
    out. Next, reconnect the power cord and turn projector power back on.
    If the error occurs again when you turn power back on, contact your 
    retailer or nearest authorized CASIO Service Center. STATUS : Red flashing
    (2-second or 1-second 
    interval)
    Message : –
    Projector Troubleshooting
    ProblemCause and Recommended Action
    Power does not turn on.If the POWER/STANDBY indicator is not lit, the AC power cord is not connected 
    correctly. Connect the AC power cord correctly.
    If the POWER/STANDBY indicator is lit red and the STATUS indicator is lit (or 
    flashing) red or amber, it means some type of error has occurred. See “Error 
    Indicators and Warning Messages” (page 69).
    No image is projected or 
    the projected image is 
    abnormal.The computer or video device connected to the projector is not turned on or it is 
    not outputting a video signal. Make sure the connected computer or video device 
    is turned on, and perform the required operation on it to output a video signal.
    The correct output source is not selected on the projector. On the projector, select 
    the correct input source that corresponds to the connected device.
    Images may not project correctly when you have the component output terminal of 
    a video device connected to the COMPUTER terminal of the projector.
    Image color or display is 
    very abnormal.The wrong option (“Component” or “RGB”) may be selected for the “Input Settings  
    COMPUTER Terminal” setting on the setup menu. The image will not be projected 
    correctly if “Component” is selected while the projector’s COMPUTER terminal is 
    connected to the RGB output terminal of a computer, or if “RGB” is selected while the 
    projector’s COMPUTER terminal is connected to the component video output 
    terminal of a video device. On the setup menu, select “Auto” for the “Input Settings  
    COMPUTER Terminal” setting. See page 28.
    I can’t understand 
    messages or menus 
    because they are the 
    wrong language.Perform the following operation to select the language you want. See page 29.
    1. Press the [MENU] key to display the setup menu.
    2. If the input signal is HDMI (PC), press [] four times and then press the [ENTER] 
    key. If the input signal is not HDMI (PC), press [] five times and then press the 
    [ENTER] key.
    3. Press [] twice and then press the [ENTER] key to display the language selection 
    menu.
    4. Use the [] and [] keys to move the highlighting to the language you want to 
    select and then press the [ENTER] key.
    5. Press the [MENU] key to exit the setup menu.
    Indicator/Error MessageDescription and Required Action 
    						
    All Casio manuals Comments (0)

    Related Manuals for Casio Projector XJ-F20XN User Manual