Casio Projector XJ-F20XN User Manual
Have a look at the manual Casio Projector XJ-F20XN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 338 Casio manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
41 Use the procedures in this section when you want to use File Viewer to project image files, movie files, presentation files, or PDF files from a USB flash drive or other memory device. Supported Memory Devices The Data Projector’s USB-A port supports connection of a FAT/FAT32 format memory device supported by the USB interface. The following are supported memory devices. USB flash drive Memory cards A commercially available USB card reader is required to connect a memory card to the Data Projector. USB storage class (USB Mass Storage Class) compatible digital cameras To connect a USB flash drive to the projector Connect USB flash drive to the Data Projector’s USB-A port as shown below. To connect a memory card to the projector 1.Load the memory card into a USB card reader’s card slot. For details about how to load a memory card into the USB card reader, see the user documentation that comes with the reader. 2.Connect the USB card reader to the Data Projector’s USB-A port. Projecting Files from a Memory Device Connected by USB
42 To connect a digital camera to the projector 1.If necessary, configure the digital camera’s USB mass storage class setting. 2.Turn off the digital camera and connect a USB cable to it. 3.Connect the other end of the USB cable (Type A connector) to the Data Projector’s USB-A port. 4.Turn on the digital camera. NoteFor details about steps 1, 2, and 4, see the user documentation that comes with your digital camera. To start projection of files that are on a memory device connected via USB 1.Connect the memory device where files you want to project are stored to the projector’s USB-A port. If the File Viewer main screen appears automatically, advance to step 4 of this procedure. If it doesn’t, go to step 2. Note that the File Viewer main screen will appear automatically if “On” is selected for the “Plug and Play” setting on the projector’s Setup Menu. 2.Press the [INPUT] key. This will display the “Input” dialog box. 3.Use the [] and [] keys to select “File Viewer” and then press the [ENTER] key. This will start up File Viewer and display the File Viewer main screen.
43 4.Depending on the type of file you want to project, perform one of the operations below. The screen that will appear depends on the function you selected. 5.Use the file list displayed on the screen to check the contents of the USB flash drive you connected in step 1 of this procedure or the contents of internal memory. If the file list shows the contents of a USB flash drive, go to step 7 of this procedure. If the file list shows the contents of internal memory, go to step 6. 6.Press the [FUNC] key. On the menu that appears, select “Drive Switching” and then press the [ENTER] key. 7.Depending on the function you selected in step 4 of this procedure, perform one of the operations below. To project this type of file:Perform this operation: Presentation File Use the [] and [] keys to select “Presentation” and then press the [ENTER] key. PDF File Use the [] and [] keys to select “PDF Viewer” and then press the [ENTER] key. Image File Use the [] and [] keys to select “Slide” and then press the [ENTER] key. Movie File Use the [] and [] keys to select “Movie” and then press the [ENTER] key. If you selected this function:Perform this operation: Presentation Perform the procedure from step 2 under “To project a presentation file” (page 45). PDF Viewer Perform the procedure from step 2 under “To project a PDF file” (page 46). Slide Perform the procedure from step 2 under “To project an image file” (page 47). Movie Perform the procedure from step 2 under “To project a movie file” (page 47). Function nameFolder path
44 Drive Menu Entering the Presentation Mode, PDF Viewer Mode, Slide Mode, or Movie Mode while there are multiple memory devices connected to the Data Projector’s USB-A port (multiple USB flash drive devices connected via a USB hub, multiple memory cards loaded in the memory card reader connected to the Data Projector, etc.) will cause a menu like the one shown below to appear on the projection screen. When this happens, use the cursor keys to move the highlighting to the drive you want to use and then press the [ENTER] key. This will display a menu of files for the mode you are entering. NoteThe Data Projector can recognize up to four drives. The message “NOUSB” will appear in the Drive Menu if there is no memory device connected to the projector’s USB-A port when you perform Drive Switching ([FUNC] 3 “Drive Switching” 3 [ENTER]). If this happens, perform Drive Switching again to restore the previous screen.
45 This section explains procedures you can project each type of file using File Viewer. To project a presentation file 1.On the File Viewer main screen, select “Presentation” and then press the [ENTER] key. This displays a menu of presentation (ECA or PtG) files. 2.Use the [] and [] keys to select the presentation file you want to play and then press the [ENTER] key (or [R] key). This will start playback of the currently selected presentation file. Whenever there is an automatic pause in playback, press [R] to play the next animation or to advance to the next page. 3.To return to the file menu, press the [ESC] key. 4.To return to the main screen, press the [FUNC] key and then the [ENTER] key. NoteYou can perform the operations described in the table below while presentation playback is in progress. Projecting Files To do this:Perform this operation: Go to the previous page Press the [] or [] key. Go to the next page Press the [] or [] key. Pause playback; Resume playback from where it was pausedPress the [R] key. Skip back to the start of the currently playing animationPress the [] or [s] key Skip forward to the end of the currently playing animationPress the [] or [d] key. Select a particular page from a menu of thumbnails and play back that page1. Press the [FUNC] key. 2. On the menu that appears, select “Page Selection” and then press the [ENTER] key. 3. Use the cursor keys to select the thumbnail of the page you want to play back and then press the [ENTER] key.
46 To project a PDF file 1.On the File Viewer main screen, select “PDF Viewer” and then press the [ENTER] key. This displays a list of PDF files. 2.Use the [] and [] keys to select the PDF file you want to open and then press the [ENTER] key (or [R] key). This will open the selected PDF file. 3.Perform page change, zoom, and other operations as required. The following operations are supported during PDF file projection. 4.To return to the file menu, press the [ESC] key. 5.To return to the main screen, press the [FUNC] key and then the [ENTER] key. To do this:Perform this operation: Go to the previous page Press the [] or [] key. Go to the next page Press the [] or [] key. Adjust the image to the screen widthPress the [FUNC] key. On the menu that appears, select “Adjust to Screen Width” and then press the [ENTER] key. Return to a full page view Press the [FUNC] key. On the menu that appears, select “Show Entire Page” and then press the [ENTER] key. Select a page from a thumbnail list and display it1. Press the [FUNC] key. 2. On the menu that appears, select “Page Selection” and then press the [ENTER] key. 3. Use the cursor keys to select the thumbnail of the page you want to display and then press the [ENTER] key.
47 To project an image file 1.On the File Viewer main screen, select “Slide” and then press the [ENTER] key. This displays a list of image files. 2.Use the [] and [] keys to select image file you want to open and then press the [ENTER] key. This will project the selected image file. Pressing the [R] key instead of the [ENTER] key will start an image file slideshow starting from the currently selected file. 3.Perform the rotate image and image scrolling operations described below as required. The following operations are supported during image file projection. *Supported for JPEG files only. 4.To return to the file menu, press the [ESC] key. 5.To return to the main screen, press the [FUNC] key and then the [ENTER] key. To project a movie file 1.On the File Viewer main screen, select “Movie” and then press the [ENTER] key. This displays a list of movie files. 2.Use the [] and [] keys to select the movie file you want to open and then press the [ENTER] key or [R] key. This will start playback of the selected movie file. To do this:Perform this operation: Project the previous image file Press the [] or [] key. Project the next image Press the [] or [] key. Rotate the image leftwards 90 degrees*Press the [s] key. Rotate the image rightwards 90 degrees*Press the [d] key. Start a slideshow Press the [R] key. Stop an ongoing slideshow Press the [R] key.
48 3.Perform fast forward, fast reverse, pause, and other operations as required. The operations described below are supported during movie file playback. 4.To return to the file menu, press the [ESC] key. 5.To return to the main screen, press the [FUNC] key and then the [ENTER] key. To do this:Perform this operation: Pause and resume movie playback Press the [ENTER] or [R] key. A pause icon ( ) is displayed in the upper left corner of the projection screen while movie projection is paused. Re-play the file from the beginning 1. Press the [FUNC] key. 2. On the menu that appears, select “Play from Beginning” and then press the [ENTER] key. Toggle display of the movie playback time between show and hidePress the [FUNC] key. On the menu that appears, select “Time Indicator On/Off” and then press the [ENTER] key. Fast forward at 2X, 8X, or 32X normal speed Press the [] or [d] key. The first press starts 2X speed fast forward, the second press increases to 8X, and the third press increases to 32X. The indicator appears in the upper left corner during 2X fast forward, during 8X fast forward, and during 32X fast forward. Fast reverse at 2X, 8X, or 32X normal speed Press the [] or [s] key. The first press starts 2X speed fast reverse, the second press increases to 8X, and the third press increases to 32X. The indicator appears in the upper left corner during 2X fast reverse, during 8X fast reverse, and during 32X fast reverse. Return from fast forward or fast reverse to normal playbackPress the [ENTER] key or [R] key twice. Pressing either of these keys only once will pause playback. Press once more to start normal playback. Jump to the final movie frame Press the [FUNC] key. On the menu that appears, select “Go to End” and then press the [ENTER] key. Stop movie file playback and return to the file menuPress the [ESC] key. Total movie play time Elapsed movie play time
49 There are two different views for the File Viewer file menu: a list view and an icon view. List View This view shows a list of names of folders and files in the projector internal memory, or on memory device connected to the projector’s USB port. Folders and files are displayed in this format immediately after you go from the File Viewer main screen to the Presentation Mode, PDF Viewer Mode, Slide Mode, or Movie Mode. Icon View This view shows both icons and names for the folders and files. Thumbnails are displayed for all of the files that can be played back by File Viewer. To toggle the file menu between the list view and icon view Press the [FUNC] key. On the menu that appears, select “Screen Format” and then press the [ENTER] key. NoteYou can specify either the list view or icon view as the default view. For more information, see “Configuring File Viewer Settings” on page 50. To scroll the file menu Press the [T] key to scroll forward, and the [S] key to scroll back. To open a folder Use the cursor keys to move the highlighting to the folder you want to open and then press the [ENTER] key. To exit the current folder and move up to the next level Press the [ESC] key. To return to the main screen from the file menu Press the [FUNC] key. On the menu that appears, select “Back to top menu” and then press the [ENTER] key. File Menu Operations
50 This section explains how to configure File Viewer settings, including those that control what appears on the File Viewer file menu. To configure File Viewer settings 1.On the File Viewer main screen, select “Viewer Settings” and then press the [ENTER] key. This displays the “Viewer Setup” screen. 2.Use [] and [] to select the item whose setting you want to change. 3.Use [] and [] to change the currently selected setting. For information about the settings available for each item, see “File Viewer Setting Items”. 4.Repeat steps 2 through 3 as many times as necessary to configure all of the settings you want. 5.After all the settings are the way you want, press the [ESC] key to return to the File Viewer main screen. Configuring File Viewer Settings