Casio Projector XJ-F20XN User Manual
Here you can view all the pages of manual Casio Projector XJ-F20XN User Manual. The Casio manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 81
81 Component Signal Video Signal (XJ-F Series only) HDMI Signal Signal NameHorizontal Frequency (kHz)Vertical Frequency (Hz) HDTV1080p/50 56.3 50 1080p/60 67.5 60 720p/50 37.5 50 720p/60 45.0 60 1080i/50 28.1 50 1080i/60 33.7 60 SDTV576p/50 31.3 50 576i/50 16.6 50 480p/60 31.5 60 480i/60 15.7 60 Signal NameHorizontal Frequency (kHz)Vertical Frequency (Hz) NTSC 15.7 60 NTSC4.43 15.7 60 PAL 15.6 50 PAL-M 15.7 60 PAL-N 15.6 50 PAL60 15.7 60 SECAM 15.6 50 Signal NameHorizontal Frequency (kHz)Vertical...
Page 82
82 When there is a serial connection between the projector and a computer, you can control the projector using RS-232C commands sent from the computer. To establish a serial connection between the projector and a computer Connect the projector and computer as shown in the illustration below. XJ-V Series XJ-F Series Projector RS-232C Control Projector Commercially available serial cable (cross) Computer SERIAL port (RS-232C) D-Sub 9-pin (female) Serial port D-Sub 9-pin (female) Projector Commercially...
Page 83
83 Using Control Commands This section explains the commands that are used to control the projector from a computer. Command Send Format See the “Command List” for details about command names and settings. All commands use ASCII characters and decimal format integers. The projector will return a question mark (?) when it is sent a command it cannot recognize. Also, any command that attempts to set a value that is outside the applicable allowable range will be ignored. If the projector is performing...
Page 84
84 Command List Only the following functions are supported while the projector is turned off. Do not try to send any other command to the projector. Input of a valid signal must be in progress in order to use a command to turn on blank screen or change the aspect ratio. R: Read enabled W: Write enabled Power on/off: Read Power on: Write Get light time: Read FunctionCommand NameRWSettings Power On/Off:PWR RW 0: Off, 1: On Input Switching: 0:Switches the input source to the COMPUTER terminal and...
Page 85
85 Light Control: Configures the Light Control settings and Light Control Off Mode settings. Setting 2 is valid for XJ-F Series projectors only.PMD RW 0: Bright, 1: Normal 2: Light Sensor On 3: Light Output 7 4: Light Output 6 5: Light Output 5 6: Light Output 4 7: Light Output 3 8: Light Output 2 9: Light Output 1 Freeze:Switches freeze on or off. FRZ RW 0: Off, 1: On Keystone Correction: Specifies the keystone correction setting as a value that corresponds to the typical Setup Menu “Keystone...
Page 86
86 Volume +/–:Raises or lowers the current volume setting by 1. +: VLP –: VLMW0 to 30 Mute:Switches mute on or off. MUT RW 0: Off, 1: On Microphone Input Level: Adjusts the volume level of audio input from the MIC terminal. This command is available only for network model projectors.MIC RW 0 to 3 *1 Top of projector upwards *2 Top of projector downwards FunctionCommand NameRWSettings
Page 87
87 GPL and LGPL (1) This product uses software (This Software) that comes under the GNU General Public License (GPL) and GNU Lesser General Public License (LGPL). In accordance with the GPL and LGPL, the source code of This Software is open source code. Anyone who wishes to view the open source code can do so by downloading it from the CASIO Projector download site. Whenever copying, modifying, or distributing This Software, be sure to do so in accordance with the terms and conditions of the GPL and...
Page 88
88 GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free...
Page 89
89 TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0.This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with...
Page 90
90 These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose...