Casio Projector XJ-F20XN User Manual

21
Light Control lets you adjust the light being output (light source brightness) by the projector. When 
“On” is selected for “Light Control” on the Setup Menu (initial default setting), light output can be 
adjusted to one of seven levels.
With the XJ-F Series, selecting “On” for the Setup Menu “Light Sensor” setting will cause light output 
to be adjusted automatically in accordance with currently available light.
NoteTo project at maximum light source brightness, select “Off” for the “Light Control”...

22
To check the power saving level
1.Press the [ ] key.
This displays a light control dialog box. The current power saving level is indicated by leaf ( ) 
marks at the top of the dialog box. The more leaf marks there are, the higher the power saving 
level.
At this time you can adjust the light output level using the [] and [] keys.
2.To close the dialog box, press the [ESC] key.
NoteThe above operation cannot be performed while “Off” is selected for the “Light Control” 
setting on the Setup Menu....

23
The presentation timer shows a countdown from a preset time value. You can use it to keep track of 
how much time has elapsed during your presentation, and to limit a presentation to a preset amount of 
time. You can configure the presentation timer so it is displayed in the projected image.
To display the timer
When the timer is not displayed on the projected image, press the [TIMER] key once.
The timer will appear for about five seconds and then disappear automatically if the “Off” is selected 
for...

24
To configure timer settings
1.Use the [TIMER] key to display the timer function menu.
2.Use the [] and [] keys to select the “Position”, “Continuous Display”, or “Start 
Time” setting and then change the settings as described in the table below.
3.To save your settings and close the timer function menu, press [ESC].
To start the timer immediately after changing its settings, use [] and [] to select “Start 
Timer” on the timer function menu and then press the [ENTER] key before pressing [ESC] in...

25
To pause the timer countdown
1.Use the [TIMER] key to display the timer function menu.
2.Select “Pause Timer” and then press the [ENTER] key.
To resume a paused timer countdown
1.Use the [TIMER] key to display the timer function menu.
2.Select “Restart Timer” and then press the [ENTER] key.
To reset the timer to its start time
1.Use the [TIMER] key to display the timer function menu.
2.Select “Reset Timer” and then press the [ENTER] key.
This will reset the time to the “Start Time” setting. 

26
Pressing the [MENU] key displays the Setup Menu shown below on the projection screen. You can 
use this menu to adjust projected image brightness, contrast, and other settings, and to change 
projector settings.
The guidance shows the key operations that can be performed for the currently selected (highlighted) 
menu item.
Using the Setup Menu (MENU)
Basic Setup Menu Operations
To do this:Perform this operation:
Display the Setup Menu
Exit the Setup MenuPress the [MENU] key. Pressing the [MENU] key to...

27
One or more letters (such as RCV) after the menu item name indicates an item that is available only 
when one or more particular input source is selected. The letters indicate the input source(s) where 
the menu item is available.
R: RGB input, C: Component input, V: S-video input*
1 or Video input*1, H: HDMI (PC) input, 
D: HDMI (DTV) input, F: File Viewer*2, T: CASIO USB Tool*2, N: Network*2, U: USB Display*2
A menu item that does not have any letter after it will be available regardless of the...

28
Image Adjustment 2 3 
Overscan (CVD)Adjust the overscan amount for an input video signal within the range of 0% to 5%*. 
The size of the border area displayed on the projection screen depends on the 
setting value. A smaller value results in a wider border area as shown below.
Image Adjustment 2 3 
Restore Menu Defaults 
(RCVD)Return all of the items in the “Image Adjustment 2” main menu to their initial defaults 
for the currently projecting image source.
Volume Adjustment 3 
VolumeSee “Adjusting the...

29
Input Settings 3 
Video Signal (V) 
Input Settings 3 
S-Video Signal (V) Specify the method to be used to identify the VIDEO terminal input signal.
Auto*: Projector automatically identifies the video input signal.
NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM:
Always assumes the video input signal is the specified video signal type.
Input Settings 3 
Signal Name IndicatorSpecify whether the newly selected input signal type should be displayed (On*) or 
not displayed (Off) when the [INPUT] key is...

30
Option Settings 2 3 
Audio Out Use this sub-menu to specify whether audio input from the input sources below 
should be output to the speaker (Speaker*) or output to an external destination 
(Line)*
1.
HDMI
File Viewer (Movie playback audio)*
2
Wireless or Network (Video stream projection movie audio)*2
USB Display*2
*1 When Line is specified, the projector will output audio from its AUDIO OUT 
terminal.
*2 Network models only
Option Settings 2 3 
High AltitudeTurn the high-altitude fan speed...