Casio EX FC100 User Manual

21Quick Start Basics
NOTE
• Each country controls its local time offset and the use of summer time, and so they 
are subject to change.
• Removing the battery from the camera too soon after configuring time and date 
settings for the first time can cause the settings to be reset to their factory defaults. 
Do not remove the battery for at least 24 hours after configuring settings. If you make a mistake configuring display language, date, or time settings with the 
above procedure, refer to the following...

22Quick Start Basics
Though the camera has built-in memory that can be used to store images and 
movies, you probably will want to purchase a commercially available memory card for 
greater capacity. The camera does not come with a memory card. Images recorded 
while a memory card is loaded are saved to the memory card. When no memory card 
is loaded, images are saved to built-in memory.
• For information about memory card capacities, see page 183.
– SD Memory Card
– SDHC Memory Card
Use one of the above...

23Quick Start Basics
1.Press [ON/OFF] to turn off the camera 
and then open the battery cover.
Slide the battery cover release in the 
direction indicated by arrow 
1 and then 
open the battery cover as indicated by 
arrow 
2.
2.Load a memory card.
Positioning the memory card so its front 
is facing upwards (towards the monitor 
screen side of the camera), slide it into 
the card slot all the way in until you hear 
it click securely into place.
3.Close the battery cover.
• For information about how to...

24Quick Start Basics
You need to format a new memory card before using it for the first time.
1.Turn on the camera and press [MENU].
2.On the “Set Up” tab, select “Format” and then press [6].
3.Use [8] and [2] to select “Format” and then press [SET].
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete 
its contents. Normally you do not need to format a memory card again. However, if 
storing to a card has slowed down or if you notice any other abnormality,...

25Quick Start Basics
To enter the REC mode, press [ON/OFF] (Power) or 
[r] (REC). To enter the PLAY mode, press [p] 
(PLAY).
The back lamp will light (green) momentarily and the 
camera will turn on. If you are entering the REC mode, 
the lens will extend from the camera at this time.
• Take care to ensure that nothing is restricting or 
coming into contact with the lens as it extends. 
Holding the lens with your hand so it cannot extend 
creates the risk of malfunction.
•Pressing [p] (PLAY) while in the...

26Quick Start Basics
The following procedure describes how to shoot a single snapshot. For information 
about shooting a series of shots (Continuous Shutter), see page 50.
1.Press [r] (REC) to turn on the camera.
Make sure R (Auto) is on the display. If it isn’t, see page 66.
2.Point the camera 
at the subject.
You can zoom the 
image, if you want.
To shoot a snapshot 
Auto icon
Remaining snapshot memory 
capacity (page 183)Monitor screen
Shutter button
[r] (REC)
w Wide Anglez TelephotoZoom controller 

27Quick Start Basics
3.Half-press the shutter button to focus the image.
When focus is complete, the camera will beep, the back lamp will light green, and 
the focus frame will turn green.• If the current aperture, shutter speed, ISO  sensitivity, or Auto Exposure is not 
correct, the setting will turn orange when you half-press the shutter button.
Focus frameBack lamp
Shutter speed Aperture value
ISO sensitivity
Half-press
Press lightly 
until the 
button stops.
Beep, beep (Image is in focus.)
When you...

28Quick Start Basics
4.Continuing to keep the camera still, press the shutter button the rest of 
the way down.
This records the snapshot.
Full-press
Snap (Image is recorded.)
Shooting a Movie
Press [0] (Movie) to start movie recording. Press [0] (Movie) 
again to stop movie recording. See the following pages for 
details.
Standard movie (STD movie): page 58
High-definition movie (HD movie): page 60
High speed movie (HS movie): page 61[0] (Movie) 

29Quick Start Basics
.Using Quick Shutter
Fully pressing the shutting button without waiting for Auto Focus to operate will record 
using Quick Shutter (page 93).
• With Quick Shutter, the camera focuses faster than normal Auto Focus, which 
means you can capture quick moving action more easily. Note, however, that some 
images may be out of focus when Quick Shutter is used.
• Whenever possible, take a little extra time to half-press the shutter button in order 
to ensure proper focus.
.If the image does...

30Quick Start Basics
Your images will not come out clearly if you move the camera when you press the 
shutter button. When pressing the shutter button, be sure to hold the camera as 
shown in the illustration below, and keep it still by pressing your arms firmly against 
your sides as you shoot.
Holding the camera still, carefully press the shutter button and take care to avoid all 
movement as the shutter releases and for a few moments after it releases. This is 
especially important when available...