Carrier Comfort Zone 1 Manual
Here you can view all the pages of manual Carrier Comfort Zone 1 Manual. The Carrier manuals for Thermostat are available online for free. You can easily download all the documents as PDF.
Page 1
® HEAT COOL M AM HOME OWNER’S GUIDE NOTE TO INSTALLER: THIS MANUAL SHOULD BE LEFT WITH THE EQUIPMENT USER. COMFORT ZONE A GUIDE TO OPERATING YOUR RESIDENTIAL COMFORT ZONE SYSTEM
Page 2
2 HEAT COOL M AM HEAT COOLM AM 9S TZONE 1 OPTIONS VACATIONZONE 2 ZONE 4ZONE 3SET TIME/TEMP SCHEDULES HOLD TEMPERATURES OFF OFFAUTO HEAT COOL FAN EMERGENCY HEATAUTO SELECT MIN/HR/DAY8 7 6 5 4 3 21 OFF ONADVANCE TIME/DAYON AUTO ! OFF OFFAUTO HEAT COOL FAN EMERGENCY HEATAUTOOFF ONON AUTO ! SET TIME/TEMP SCHEDULES HOLD TEMPERATURESSELECT MIN/HR/DAY ADVANCE TIME/DAY 9S TZONE 1 OPTIONS VACATIONZONE 2 ZONE 4ZONE 38 7 6 5 4 3 21 INTRODUCTION The Comfort Zone Controller is the Program Center...
Page 3
3 SYSTEM SWITCHES System Switches select the desired equipment operation. Heat Switch A95555 OFF - Heat will not come on. AUTO - Heat will turn on when any zone is more than 1.5 ° F below the desired heat setpoint. Cool Switch A95556 OFF - Cooling will not come on. AUTO - Cooling will turn on when any zone is more than 1.5 ° F above the desired cool setpoint. Fan Switch A95557 ON - Fan will stay on continuously (recommended). AUTO - Fan will come on only when heating or...
Page 4
4 NORMAL OPERATION When set for normal operation (alternate display not ON), the Comfort Zone Controller display shows the current zone temperature setpoints and allows the adjustment of these setpoints using the setpoint buttons. If the alternate display feature is turned on (see Toggles Section), the controller display alternates between displaying the zone setpoints and zone temperature every 2 sec. Cooling Setpoint Buttons Heating Setpoint Press to raise or lower Press to raise or lower...
Page 5
5 ZONE SETPOINTS To view the setpoints for each zone, turn the Zone Selector Dial to the ZONE No. you wish to view. The setpoints for the selected zone will be displayed in the controller display. A95561 Example Setpoints Sat., Start Time - 7:00 AM ZONE 1 - Family and Living Rooms ZONE 2 - Kitchen and Laundry ZONE 3 - Bedrooms ZONE 4 - Home Office A95562 ______________________________________________ PROGRAM SCHEDULES Each zone has 3 different weekly periods (Weekdays, Saturday and Sunday),...
Page 6
6 VACATION MODE Vacation mode displays the current vacation temperature setpoints and allows the adjustment of these setpoints using the setpoint buttons. These setpoints control all zones until the selector dial is returned to 1 of the zone selection positions, then normal independent zone operation will resume. This mode can also be used to maintain the entire building at 1 constant temperature. NOTE: If the FAN switch is set to ON, the fan will continue to run in vacation mode. To enter...
Page 7
7 SETTING THE CLOCK The Clock Display will normally show the hr, minutes, AM or PM, and the day. Clock Display Follow these steps to adjust the clock settings. A95566 1. Set the Minutes Press the SELECT MIN/HR/DAY button once. Press the ADVANCE TIME/DAY button to scroll to the proper minutes. A95567 2. Set the Hour Press the SELECT MIN/HR/DAY button once again. Press the ADVANCE TIME/DAY button to scroll to the proper hr, AM or PM. A95568 M AM SET TIME/TEMP SCHEDULES HOLD...
Page 8
8 SETTING THE CLOCK 3. Set the Day Press the SELECT MIN/HR/DAY button once again. Press the ADVANCE TIME/DAY button to scroll to the proper day. A95569 4. Return to Normal Operation Press the SELECT MIN/HR/DAY button once again. The newly programmed time and day will be displayed. A95570 TSET TIME/TEMP SCHEDULES HOLD TEMPERATURESSELECT MIN/HR/DAY ADVANCE TIME/DAY SET TIME/TEMP SCHEDULES HOLD TEMPERATURESSELECT MIN/HR/DAY ADVANCE TIME/DAY T AM
Page 9
9 PROGRAMMING THE SYSTEM NOTE: See programming chart in rear of owner guide. 1. Enter Program Mode Press the SET TIME/TEMP SCHEDULES button to enter program mode. The program mode and the current zone will be shown on the controller display. A95571A95572 2. Select a Zone Turn the Selection Dial to the ZONE to be programmed. Choices are ZONE 1, ZONE 2, ZONE 3, or ZONE 4. A95561 A95573 HOLD TEMPERATURES SELECT MIN/HR/DAY ADVANCE TIME/DAY SET TIME/TEMP SCHEDULES HEAT PROGRAM COOL 9S...
Page 10
10 PROGRAMMING 3. Select a Weekly Period The clock display will show “MTWTHF.” Pressing the ADVANCE TIME/DAY button selects the weekly period to be programmed. A94475 Pressing the ADVANCE TIME/DAY button 1 time will change the clock display from “MTWTHF” to “SA.” A second press will change the display to “SU.” A third press returns the display to “MTWTHF.” A95576 _____________________________________________ 4. Program Time Periods There are 4 start times that can be programmed in each...