Canon Selphy Es30 User Guide

							
Preparing/Replacing/Storing the Easy Photo Pack
21Getting Started
Inserting the Easy Photo Pack into the Printer
1Check that the ink sheet is tight and that the paper is correctly 
loaded in the cartridge.
2Slide the cartridge cover lever up to open the cartridge cover.
3If there is a cleaner unit inside the printer, grasp it and remove it.
• Do not touch the ink sheet of the cartridge, or pull out the ink sheet or papers.There may not be enough ink left for the allotted sheets, or paper jams or poor printing may result.
• Do not handle the cartridge with wet or sweaty hands.
• Please use only cartridges specified for use with the SELPHY ES series (Cartridges for the CP  series cannot be used).
• Do not apply excessive force to the cartridge. The paper may come out from under the clips. In this case, push the paper back under the clips.
Ink sheet Clip

C
O
P
Y  
						

							
Preparing/Replacing/Storing the Easy Photo Pack
22Getting Started
4Make sure that the cartridge is oriented as shown by the direction 
indicator on the inside of the printer, and insert the cartridge until it 
clicks into place.
5Press the area marked PUSH to close the cartridge cover.
Protective paper
Direction 
indicator

C
O
P
Y  
						

							
Preparing/Replacing/Storing the Easy Photo Pack
23Getting Started
1• When inserting the cartridge into the printer, if the ink sheet is so slack it catches, insert the cleaner unit and turn it slowly to take up the slack.
• It will not be possible to use all the paper for printing if you overwind the ink sheet.
4• The colored paper on the top side of the cartridge is protective paper. Load the cartridge with  this paper still in place.
• Some cartridges have an orange colored stopper on the backside. Remove the stopper then  insert the cartridge into the printer.

C
O
P
Y  
						

							
Preparing/Replacing/Storing the Easy Photo Pack
24Getting Started
Replacing the Easy Photo Pack
Replace the Easy Photo Pack when paper has run out, or if another sheet size is required.
1Push and slide the cover lever up to open the cartridge cover ( ), 
then push and slide the cartridge lever down ( ).
• Eject the Easy Photo Pack.
2Remove the Easy Photo Pack.
3Replace the Easy Photo Pack following the procedures in inserting 
the Easy Photo Pack into the printer (p. 21).
• Do not remove the Easy Photo Pack while paper is being fed into or ejected from the printer, or 
while printing is in progress.
• When replacing the Easy Photo Pack, remove all paper from the print output receptacle.
• Do not reuse empty Easy Photo Packs. Attempting to reuse an empty Easy Photo Pack may result  in malfunction or damage to the printer.
3• You can check the type of the Easy Photo Pack and the amount of remaining paper (ink) 
loaded in the printer, by the icons displayed in the print confirmation, printing or standby 
screens (p. 17).
• After power is turned on, or immediately after the cartridge cover is opened or closed, the  status icon is not displayed. This icon is displayed when one sheet has been printed.

C
O
P
Y  
						

							
Preparing/Replacing/Storing the Easy Photo Pack
25Getting Started
Storing Easy Photo Packs
When storing the Easy Photo Pack, return it to its original package.

C
O
P
Y  
						

							
26Getting Started
Placing/Connecting the Printer
Set up and connect your SELPHY printer in the following manner for safe use.
1Place the printer on a flat surface.
2Connect the supplied power cord to the printer.
3Insert the plug into a power outlet.
• Do not place the equipment on an unstable or tilted surface.There is risk that the equipment may fall and cause injury.
• Be sure to select a safe place to avoid tripping over the power cord.
• Do not block the air vents on the back of the printer.
To power outlet 15 cm 
(6 in.)10 cm 
(4 in.) 15 cm 
(6 in.)Leave more than 15 cm 
(6 in.) of clearance at the 
front and back of the 
equipment and 10 cm (4 
in.) of clearance on both 
sides.

C
O
P
Y  
						

							
27Getting Started
Printing Precautions
These cautions apply to Printing from Memory Cards, Printing from a Camera, Wireless Printing, 
and Printing from a Computer. 
zDo not eject the Easy Photo Pack or open the cartridge cover right after turning the power on or 
while printing. It may result in equipment damage.
z During the printing operation, paper is temporarily  output from the printer. Do not touch the 
paper until printing ends. This could impede pr inting, or may result in equipment damage.
z Do not allow 50 or more sheets to accumulate  in the print output receptacle while printing.
z Do not close the print output receptacle cover when printing. If closed accidentally, press the 
print output receptacle button to open the cover.
z If the printer overheats, it will  temporarily stop operating. The printer will resume normal printing 
as soon as it cools down (This will occur if t he room is unusually warm or you are printing 
continuously).
z Do not print on printed paper.

C
O
P
Y  
						

							
28Printing from Memory Cards
Printing from Memory 
Cards
Print images from a memory card that is inserted 
into the printer.
• Make sure that a camera or computer is not connected to the printer.
• This printer supports image data conforming to the Design rule for Camera File system (Exif compliant) and DPOF (Ver.1.00) standard.
• Images that have been edited on a computer might not be displayed or printed 
successfully.
• An image that has been taken by a mobile phone, depending on the size of the image  when the image was taken, might not be displayed or printed successfully.
• Movies cannot be played back on this printer.

C
O
P
Y  
						

							
29Printing from Memory Cards
Compatible Memory Cards
: You need to use the specific adapter for the card. Please purchase the specific adapter.
*1 Reduced-Size MultiMediaCard is referred to as RS-MMC.
*2 Purchase the CompactFlash Card Adapter for xD-Picture Card.
About Compatible Memory Cards• Operation with all memory cards listed below cannot be guaranteed.
• Do not add labels or stickers to memory cards. The memory card may get stuck inside the card slot 
and may not be removed. 
• Use a memory card formatted with your camera. Images from a memory card formatted with a 
computer may not be recognized. 
• For memory cards requiring an adapter, be sure to first insert the memory card into the adapter  before inserting the adapter into the appropriate card  slot. If you insert the memory card into a card 
slot without first inserting it into an adapter, you may not be able to remove the memory card from 
the printer.
SlotMemory Cards
SD Memory Card
miniSD Card
SDHC Memory Card
miniSDHC Card
MultiMediaCard
MMCplus Card
HC MMCplus Card
MMCmobile Card
MMCmicro Card
RS-MMC Card
*1
microSD Card
microSDHC Card
CompactFlash Card
Microdrive
xD-Picture Card*2
Memory Stick
Memory Stick PRO
Memory Stick Duo
Memory Stick PRO Duo
Memory Stick micro

C
O
P
Y  
						

							
30Printing from Memory Cards
Insert a Memory Card
Insert a single memory card into the printer.
Please refer to the user guide included with your memory card for handling instructions.
1Press   until the power lamp lights 
green to turn the power on.
2Insert a single memory card into the 
appropriate card slot of the printer.
• The startup screen appears on the LCD 
monitor.
• An image is displayed  on the LCD monitor.
Label side
2• Slide the card slot cover to 
switch from SD/MMC+/miniSD 
slot to microSD slot.
• Insert a memory card all the  way in (for microSD cards, 
microSDHC cards, push the 
card in until you hear a click).
• When you remove a memory  card from a card slot, grasp the 
portion of the card protruding 
from the card slot, and pull it out 
(for microSD cards, microSDHC 
cards, push the memory card in 
until you hear a click, and after it 
silently pops out, grasp it and 
pull it out).
• There is a lead-in guide to be  tailored to the size of the 
memory card in the SD/MMC
+/
miniSD slot. Insert a small 
memory card, such as a miniSD 
Card, along the lead-in guide.
• If the confirmation screen for  whether or not to use DPOF for 
printing is displayed on the LCD 
monitor, select [OK] or [Cancel] 
then follow the instructions 
below.
[OK] : Step 3 on Page 37
[Cancel] : Page 31

C
O
P
Y