Canon Selphy Cp900 User Guide

							51
Wireless LAN
 OThe printer's SSID (network name) is not displayed on the smartphone
• Select ad hoc mode  (p.  29).
•
 Check if your smartphone supports ad hoc mode. If it does not support ad\
 hoc mode, connect with 
infrastructure mode  (p.  31).
•
 Do not use wireless LAN near a device that uses 2.4 GHz frequency band s\
uch as a microwave oven or 
Bluetooth since it will cause radio wave interference.
•
 Place the printer and smartphone close and do not place any object betwe\
en them.
 O Cannot connect after changing the WEP key
• After changing the WEP key in ad hoc mode (p.  29), enable the new WEP key by turning off the 
printer, and then turning it on again. 

Then, enter the new WEP key on the smartphone.
 OThe access point is not displayed on the list
 OCannot connect in infrastructure mode
• If you have many access points and the one you want to connect to is not\
 displayed on the list, use WPS 
Connection  (p.  34) or Manual Settings  (p.  33) to connect to it.
•
 Do not use wireless LAN near a device that uses 2.4 GHz frequency band s\
uch as a microwave oven or 
Bluetooth since it will cause radio wave interference.
•
 Place the printer and access point close and do not place any object bet\
ween them.
•
 Check if the encryption key is correct and try connecting again.
•
 Check that the channel is set to one between 1 and 11 on the access point. It is recommended to 
manually fix the channel between 1 and 11 rather than leaving it to automatically select the number.  
Refer to the user guide supplied with your access point for information \
on how to check and change the 
settings.
•
 If you are using a MAC address filter or IP filter on your access point, register the printer information you 
checked in [Confirm Settings]  (p.  41) to the access point.  In such a case, disable the privacy separator 
function. Refer to the user guide supplied with your access point for in\
formation on how to modify and 
check the settings.
•
 Set the IP address manually  (p.  41) if you are using WEP security on your network and not using DHCP.
 OCannot connect to SELPHY
• Turn SELPHY’s power off, and then turn it on again. If a connection still cannot be establishe\
d, check the 
settings of the access point or device that you are trying to connect wi\
relessly.
 OPrinting takes time, or wireless connection is disconnected
• Do not use wireless LAN near a device that uses 2.4 GHz frequency band s\
uch as a microwave oven or 
Bluetooth since it will cause radio wave interference. 
Note that images may take a long time to send even when [
] is displayed.
•
 Place the printer and smartphone close and do not place any object betwe\
en them in ad hoc mode.
•
 Place the printer and access point close and do not place any object bet\
ween them in infrastructure 
mode.
Error Messages
If a problem occurs with SELPHY, a message appears on the screen. If a possible solution displays with \
the error message, follow the on-screen instructions. If you have an err\
or message only, check items in 
"Troubleshooting"  (p. 
 49).
If these items do not solve your problem, contact a Canon Customer Suppo\
rt Help Desk.
 O If a problem occurs while SELPHY is connected to a digital camera, an error message may appear for you t\
o 
check on the screen of the digital camera.

COPY  
						

							52
Specifications
SELPHY CP900
Printing MethodDye-sublimation thermal transfer (with overcoating)
Resolution/Color Representation 300 x 300 dpi
Gradation 256 shades per color
Ink Dedicated color ink cassette (Y/M/C/overcoating)
Paper Postcard Size, L Size, Card Size (including full page label sheets, 8-label sheets)
Print Size Borderless Bordered
Postcard Size
L Size
Card Size
(Each label on an 8-label sheet) 100.0 x 148.0 mm (3.94 x 5.83 in.)
89.0 x 119.0 mm (3.50 x 4.69 in.)
54.0 x 86.0 mm (2.13 x 3.39 in.)
22.0 x 17.3 mm (0.87 x 0.68 in.) 91.3 x 121.7 mm (3.59 x 4.79 in.)
79.1 x 105.1 mm (3.11 x 4.14 in.)
49.9 x 66.6 mm (1.96 x 2.62 in.)
–
Printing Speed *
1Printing from memory cards/USB flash memory/Connected to cameras 
(PictBridge)
Postcard Size
L Size
Card Size Approx. 47 sec.
Approx. 39 sec.
Approx. 27 sec.
Feeding System Automatic paper feed from paper cassette
Ejection System Automatic paper ejection on top of paper cassette
Screen Tilt-up, 2.7 type, TFT LCD Color Monitor
Interface Hi-Speed USB Connecting to a PictBridge compliant device: USB compliant Type A connector
Connecting to a computer: USB compliant Mini-B connector
Memory Cards
SD Memory Card, SDHC Memory Card, SDXC Memory Card, MMC Card, MMCplus 
Card, miniSD Memory Card*2, miniSDHC Memory Card*2, microSD Memory 
Card*2, microSDHC Memory Card*2, microSDXC Memory Card*2, RS-MMC Card*2, 
MMCmobile Card*2, MMCmicro CardWireless LANSpecification: IEEE802.11b/g
Supported Wireless Channels: 1 - 11
Connection Mode: Infrastructure mode*
3, Ad hoc mode
Transmission Method: DSSS modulation (IEEE 802.11b), OFDM modulation (IEEE 
802.11g) 
Security: Ad hoc mode: WEP (open system authentication) (64-bit)  Infrastructure mode: No security, WEP (open system authentication) (64-bit), 
WEP (open system authentication) (128-bit), WPA-PSK (TKIP), WPA-PSK 
(AES), WPA2-PSK (TKIP), and WPA2-PSK (AES)
USB Flash Memory FAT/exFAT only supported
Operating Temperatures 5 – 40 °C (41 – 104 °F)
Operating Humidity 20 – 80%
Power Compact Power Adapter CA-CP200 B
Battery Pack NB-CP2L (Sold Separately)
Charger Adapter CG-CP200 (Sold Separately)
Power Consumption 60 W or less (4 W or less on standby)
Dimensions 178.0 x 127.0 x 60.5 mm (7.01 x 5.00 x 2.38 in.) (excluding protrusions)
Weight (printer only) Approx. 810 g (approx. 28.6 oz.)
*
1 Measured from the start of the yellow printing pass to final output.
*2 Special adapter (commercially available) is required.
*3 Supports Wi-Fi Protected Setup.

COPY  
						

							53
Compact Power Adapter CA-CP200 B
Rated Input 100 – 240 V AC (50/60 Hz) 1.5 A (100 V) – 0.75 A (240 V)
Rated Output 24 V DC, 1.8 A
Operating Temperatures 0 – 45 °C (32 – 113 °F)
Dimensions 122.0 x 60.0 x 30.5 mm (4.80 x 2.36 x 1.20 in.) (excluding power cord)
Weight Approx. 310 g (10.9 oz.)
Dust Protection Cover DPC-CP100
This may not be included in some regions. Purchase separately if require\
d.Dimensions 137.5 x 117.0 x 27.2 mm (5.41 x 4.61 x 1.07 in.)
Weight Approx. 88 g (3.1 oz.)
Charger Adapter CG-CP200 (Sold Separately)
Rated Input DC 24 V
Rated Output DC 24 V
Operating Temperatures 5 – 40 °C (41 – 104 °F)
Dimensions 156.2 x 49.0 x 35.5 mm (6.15 x 1.93 x 1.40 in.)
Weight Approx. 134 g (4.73 oz.)
Batter y Pack NB-CP2L (Sold Separately)
Type Rechargeable lithium-ion battery
Nominal Voltage 22.2 V DC
Nominal Capacity 1200 mAh
Battery Life (Charge Cycles) Approx. 300 times
Operating Temperatures 5 – 40 °C (41 – 104 °F)  
Dimensions 110.0 x 40.7 x 37.5 mm (4.33 x 1.60 x 1.48 in.)
Weight Approx. 230 g (8.11 oz.)
 O All data is based on tests by Canon. OPrinter specifications or appearance are subject to change without notic\
e.
USA and Canada only:
As a participant in the international Energy Star Program, we believe this product satisfies 
the standards of the Energy Star Program.
CAUTIONRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATION.
Use of  genuine Canon accessories is recommended.This product is designed to achieve excellent performance when used with genuine Canon accessories. 
Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by 
the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). 
Please note that this warranty does not apply to repairs arising out of \
the malfunction of non-genuine 
Canon accessories, although you may request such repairs on a chargeable\
 basis.

COPY  
						

							54
Handling SELPHY
 ODo not apply strong force or vibration. This may cause paper jams or the printer to malfunction. ODo not expose SELPHY to insect sprays and volatile liquids. Do not allow SELPHY to be in contact with 
rubber or plastic products over a long time. This may deteriorate the external casing.
 ODepending on the room temperature, SELPHY may overheat and temporarily stop operating. This is not 
a malfunction. Wait for a while untill SELPHY cools down and restarts operating. Printing may take longer 
when continuously printing, the room temperature is high, or SELPHY’

s rear air vent (p. 
 6) is blocked 
because SELPHY will temporarily stop printing due to overheating.
 O When moving SELPHY from a cold place to a warm place, insert SELPHY in an airtight plastic bag 
in advance and remove after SELPHY has reached room temperature to avoid condensation. If 
condensation forms, leave SELPHY in room temperature until the condensation evaporates naturally

.
 OClean SELPHY with a soft dry cloth. OIf dust accumulates on the air vent (p.  6), remove the ink cassette (p.  14) and clean away the dust. The 
printing results may not be clean if dust gets in from the air vent.
 O Never clean SELPHY with solvents such as benzine or thinner, or mild detergent. This may 
deteriorate or deform the external casing, or the coating may peel of f.
FCC Notice
(Printer, Models CD1100 and CD1107 Systems)
This device complies with part 15 of the FCC Rules. Operation is subject\
 to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a\
 Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf\
ul
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy an\
d, if not installed and used in
accordance with the instructions, may cause harmful interference to radi\
o communications. However, there is
no guarantee that interference will not occur in a particular installati\
on. If this equipment does cause harmful
interference to radio or television reception, which can be determined b\
y turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of \
the following measures:
•
 Reorient or relocate the receiving antenna.
•
 Increase the separation between the equipment and receiver.
•
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
 Consult the dealer or an experienced radio/TV technician for help.
The cable with the ferrite core provided with the printer must be used w\
ith this equipment in order to comply with
Class B limits in Subpart B of Part 15 of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A., Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516) 328-5600
Canadian Radio Interference RegulationsThis Class B digital apparatus complies with Canadian ICES-003.

COPY  
						

							55
WPA Supplicant License
WPA Supplicant
Copyright (c) 2003-2012, Jouni Malinen  and contributors All Rights Reserved.
This program is licensed under the BSD license (the one with advertisement clause removed).
If you are submitting changes to the project, please see CONTRIBUTIONS file for more instructions.
License
This software may be distributed, used, and modified under the terms of BSD license:
Redistribution and use in source and binary forms, with or without modification, are permitted provided that 
the following conditions are met:
1.
 Redistributions of source code must retain the above copyright notice, t\
his list of conditions and the 
following disclaimer.
2.
 Redistributions in binary form must reproduce the above copyright notice\
, this list of conditions and the 
following disclaimer in the documentation and/or other materials provide\
d with the distribution.
3.
 Neither the name(s) of the above-listed copyright holder(s) nor the names of its contributors may be used 
to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS 

AND CONTRIBUTORS “AS 
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE 
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR ONSEQUENTIAL DAMAGES 
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON 
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN 
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
USA and Canada only:
The Lithium ion/polymer battery is recyclable. 
Please call 1-800-8-BATTERY for information on how to recycle this battery.

COPY  
						

							CDP-E513-010  © CANON INC. 2012
Trademarks and Licenses
 ODCF is a collective trademark of Japan Electronics and Information Technology Industries Association and 
a registered trademark in Japan.
 OThe SDXC logo is a trademark of SD-3C, LLC. OWi-Fi®,  Wi-Fi Alliance®, WPATM, WPA2TM, and Wi-Fi Protected SetupTM are trademarks or registered 
trademarks of Wi-Fi Alliance.
 O This product is implemented with exFAT technology licensed by Microsoft.
About this Guide
 OReprinting, transmitting, or storing in a retrieval system any part of t\
his guide without the permission of 
Canon is prohibited.
 OCanon reserves the right to change the contents of this guide at any tim\
e without prior notice. OIllustrations and screenshots in this guide may differ slightly from the actual equipment. OThe above items notwithstanding, Canon accepts no liability for damages \
resulting from the use of this 
product and software.
-European Union (and EEA) only-
This symbol attached on the product is according to the WEEE Directive (2002/96/EC).
-India only-
This product is not to be disposed of with your household waste, accordi\
ng to the
e-waste (Management and Handling) Rules, 2011. This product should be handed
over to a designated collection point, e.g., to an authorized collection\
 site for recycling
waste electrical and electronic equipment (EEE). Improper handling of this type of
waste could have a possible negative impact on the environment and human\
 health
due to potentially hazardous substances that are generally associated wi\
th EEE. At
the same time, your cooperation in the correct disposal of this product \
will contribute
to the effective usage of natural resources. For more information regarding retur\
n and
recycling of WEEE products, please visit http://www.canon.co.in/environment
Also, this product complies with the “India E-waste Rule 2011” and prohibits use of
lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated
diphenyl ethers in concentrations exceeding 0.1 % by weight and 0.01 % by weight for
Cadmium, except for the exemptions set in Schedule II of the Rule.

COPY