Canon scanner imageFORMULA ScanFront 330 User Manual

3-12
Chapter 3   ScanFront Setup
❏ Display Language Setting
You can select the language displayed on touch panel. If 
you change this setting, restart the scanner.
Hint
The display language setting can also be configured in 
[Language/Timezone] on the Web Menu (Administrator Mode) 
(see p. 6-30) .
❏Network Test
Confirm whether communication is enabled between the 
ScanFront and other devices on the network. Enter the IP 
address of a device and press the [Execute] button to ping 
the specified IP...

Chapter 4   ScanFront Service
1. About ScanFront Service ................................. 4-2
2. Installing ScanFront Service ............................ 4-3
System Requirements ...........................................4-3
Installation .............................................................4-3
3. ScanFront Service Setup ................................. 4-6
ScanFront Settings................................................4-6
Changing the Port Number Used for 
Communication...

4-2
Chapter 4   ScanFront Service
1.About ScanFront Service
ScanFront Service is software that supplements the network functions of the ScanFront. To use this software, install it on a computer 
connected to the same network as the ScanFront. (The computer on which ScanFront Service is installed will be herein referred to 
as the “ScanFront Service Server”.)
By configuring a ScanFront Service Server, you can send 
scanned images to locations on the network, such as the 
following, where direct transfer...

4-3
Chapter 4   ScanFront Service
2.Installing ScanFront Service
❏System Requirements
Install ScanFront Service on a computer that is connected 
to the same network as the ScanFront, and that meets the 
following requirements.
Operating System
●Windows XP (32 bit/64 bit)
●Windows Server 2003 (32 bit/64 bit)
●Windows Vista (32 bit/64 bit)
●Windows Server 2008 (32 bit/64 bit)
●Windows Server 2008 R2
●Windows 7 (32 bit/64 bit)
●Windows 8 (32 bit/64 bit)
●Windows Server 2012 (64 bit)
❏Installation
1.Insert...

4-4
Chapter 4   ScanFront Service
5.Click [Next].
A screen for entering account information appears.
6.Enter the account information, and click [Next].
Use an administrator account on the computer on which 
the service will be installed.
 When entering a local account on the computer, include 
“./” at the beginning of the account name.
 If the computer is part of a domain and you are entering 
the domain account here, enter the account in one of the 
following formats.
IMPORTANT
Make sure to specify an...

4-5
Chapter 4   ScanFront Service
8.Click [Install].
Installation starts. When installation is complete, a screen 
indicating that installation is complete appears.
9.Click [Close].
Notes on Installing ScanFront Service
 ScanFront Service creates log files during operations. As 
a result, these log files and the install destination folder 
will not be deleted, even after ScanFront Service is 
uninstalled. 

4-6
Chapter 4   ScanFront Service
3.ScanFront Service Setup
❏ScanFront Settings
You must configure the following setting on the ScanFront 
to send scanned images using the ScanFront Service 
Server.
1.Log in to the Web Menu in Administrator Mode (see 
p. 6-5).
2.Click [Server Settings], and then [ScanFront Service 
Server].
3.Enter the host name (address) of the ScanFront 
Service Server.
IMPORTANT
 ScanFront Service uses port number 50000 to communicate 
with the ScanFront. Do not change the port number...

Chapter 5   Operating Procedures
1. Flow of Scanner Operations ............................. 5-2
2. Turning the Power ON and OFF ...................... 5-3
Turning the Power ON .......................................... 5-3
Turning the Power OFF ........................................ 5-3
3. Login Screen .................................................... 5-4
Login Screen Types.............................................. 5-4
When Using Server Authentication....................... 5-4
List Type Login...

5-2
Chapter 5   Operating Procedures
1.Flow of Scanner Operations
The procedure and screen transitions for the process from turning the scanner ON, to sending an image file are as follows. For 
descriptions of the various settings, refer to the appropriate reference pages. 
Turn the power ON
 (See p. 5-3.)
No user is registered
* When no user is registered and only 
the Shared Address Book and Shared 
Job Button are used 
Home screen 
(See p. 5-8.)
* Set the screen that appears after login in the user...

5-3
Chapter 5   Operating Procedures
2.Turning the Power ON and OFF
Use the power switch to turn the scanner ON, and press the [Power off] button on the touch panel to turn it OFF.
❏Turning the Power ON
Press the power switch to turn the scanner ON. The power 
indicator lights, and the Home screen or the login screen 
appears.
Hint
 It takes approximately 40 seconds for the Home screen to 
appear after the power switch is turned on. 
 If users have been registered, the login screen appears. (See 
“Login...