Canon scanner imageFORMULA DRG1130 User Manual

							1-12
Chapter 1   Before You Start Using the Scanner
Control Panel
(1) Display Panel
Displays the user mode, job info, messages, and counter.
(2) Count Clear Key
Clears and resets the counter on the display panel.
(3) Enter Key
Selects the user mode, and accepts settings.
(4)   Keys
Selects the user mode and job.
(5) Menu Key
Displays the user mode. (See p. 4-4.)
(6) Job Key
Selects jobs. (See p. 3-13.)
(7) Count Only Key
Feeds and counts the number of document pages. (See 
p. 4-2.)
(8) Separation Off Key
Raises the Document Feed Tray for the non-separating 
(manual) mode. (See p. 3-10.)
(9) New File Key
When File Separation by Key is enabled, separates files.
(10) Start Key
Starts scanning.
(11) Stop Key
Stops the scanning process.
(4) (4)
(6)
(5)
(9)
(8) (7)
(11)
(10)(2)(1)
(3) 
						

							Chapter 2   Setup1. Setup Procedures ............................................ 2-2
2. Installation Requirements ................................ 2-3
3. Software Installation ........................................ 2-4
4. Connecting the Scanner to the Computer ....... 2-6Interface Connector Locations ..............................2-6
Connecting the Scanner to the Computer .............2-65. Turning the Power ON ..................................... 2-8Turning Off the Power ...........................................2-8 
						

							2-2
Chapter 2   Setup
1.
Setup Procedures
Perform the following setup procedures to prepare the scanner for use.
Step 1: Confirm the installation requirements. (See p. 2-3)
Step 2: Install the Software. (See p. 2-4)
Step 3: Connect the scanner to the computer. (See p. 2-6)
Step 4: Turn the power ON (Scanner recognition). (See p. 2-8) 
						

							2-3
Chapter 2   Setup
2.
Installation Requirements
The following system requirements are recommended for optimal use of this scanner.■Computer
 CPU: Intel Core i3 2.13 GHz or faster
 Memory: 4 GB or more
 Hard disk: 3 GB or more available space required for 
installation of all software
 USB interface: Hi-Speed USB 2.0
 Monitor: Resolution of 1024 x 768 (XGA) or better 
recommended.
 Optical drive: Drive capable of reading DVDs.
■Operating system
 Microsoft Windows XP Service Pack 3 or later
 Microsoft Windows XP x64 Edition Service Pack 2 or 
later
 Microsoft Windows Vista Service Pack 2 or later (32-bit 
and 64-bit editions)
 Microsoft Windows 7 Service Pack 1 or later (32-bit and 
64-bit editions)
 Windows 8 (32-bit and 64-bit editions)
■Other requirement
 An ISIS-compatible application or a TWAIN-compatible 
application that is compatible with the above operating 
systems.
 .NET Framework 3.5 or later
WARNING
• Use the latest USB 2.0 driver made available by Microsoft. For 
details, consult your local authorized Canon dealer.
• Scanning speeds are slower if your computers standard USB 
interface is USB Full-Speed (equal to USB 1.1.)
• The USB cable you are using should be the one originally 
included with the scanner.
• If the CPU, memory, interface card, and other specifications 
do not satisfy the installation requirements, the scanning 
speed may be greatly reduced and transmission may take a 
long time.• Even if the computer satisfies the recommended 
specifications, the scanning speed may vary, depending on 
the specified scan settings.
• The scanner drivers provided with the scanner do not 
necessarily operate on all ISIS or TWAIN-compatible 
applications. For details, contact your application software 
provider.
• Precautions for Use in 64-bit Operating Systems
– The scanner driver supplied with this product supports 
scanning with 32bit applications only.
– Even with 32-bit applications, not all ISIS/TWAIN compliant 
applications are guaranteed to operate.
– Scanning speed may vary depending on the specifications 
of your computer. 
						

							2-4
Chapter 2   Setup
3.
Software Installation
This section describes how to install the software.
 CapturePerfect 3.1
This is a scanning application that is bundled with the 
scanner and other Canon DR series scanners.
 Scanner Driver
This is the scanner driver for this product.
IMPORTANT
Install the software before connecting the scanner to the computer.
• Log on to Windows as an Administrator.
• Close all other applications before installing the software.1.
Insert the Setup Disc into the disc drive of the 
computer.
The setup menu automatically starts up when you insert 
the disc into the drive. (If the menu does not start up, 
execute setup.exe from the disc.)
For Windows 8/7/Vista
If the [User Account Control] screen appears, click [Yes] 
or [Allow].
2.
Click [Typical Installation].
Hint
• When reinstalling the software that has been uninstalled, click 
[Custom Installation] to specify the uninstalled software. 
3.
Click [Install]. 
						

							2-5
Chapter 2   Setup
4.
Follow the instructions on the screen to complete 
installation.
Hint
Installation of EMC Cloud Capture FunctionEMC Captiva Cloud Runtime provides a component that 
enables the use of web-based applications. 
Be sure to install the component only when using a 
compatible application that supports the function.
5.
Click [Exit] to finish installing the software.
Hint
For Windows 8
Depending on the system environment, the web browser may 
start in full screen during installation. If so, wait until the browser 
processing has finished, and then return to the desktop and 
continue the installation process. 
						

							2-6
Chapter 2   Setup
4.
Connecting the Scanner to the Computer
Use a USB port to connect the device to the PC. Interface Connector LocationsThe USB connector is located on the scanner as shown below.
IMPORTANT
• Use only the supplied power cord.
• The scanner and computer should both be turned OFF when 
making connections. 
Connecting the Scanner to the ComputerTo connect to the computer, follow the procedure for the 
intended connection method.■Using a USB Connection1.
Connect the supplied power cord into the power 
connector on the back of the scanner. (1)
2.
Connect the power cord into an AC outlet. (2)
Power ConnectorUSB 
Connector
120 V Type220 - 240 V Type 
						

							2-7
Chapter 2   Setup
3.
Use the supplied USB cable to connect the scanner 
to the computer.
Connect the square plug (Type B) of the USB cable to the 
scanner. Connect the flat plug (Type A) of the USB cable 
to the computer.
Type A
Type B 
						

							2-8
Chapter 2   Setup
5.
Turning the Power ON
The power of the scanner can be turned ON and OFF with the power button on the front of the scanner.1.
Make sure that the scanner and computer are 
connected properly with the supplied USB cable.
2.
Press the power switch.HintWhen the scanner is turned on for the first time, the balloon 
message shown below appears on the Windows task bar. If you 
wait a while, automatic scanner recognition will end and the 
scanner will become ready to use.
Turning Off the PowerPress the power switch again to turn the scanner off.
IMPORTANT
• After turning the scanner off, wait at least 10 seconds before 
turning it back on.
• If you will not be using the scanner for an extended period, you 
should disconnect the power cord from the AC outlet for safety.
HintThe scanners Auto power OFF function is enabled by default, 
and the scanner will turn off automatically if it is not operated for 
4 hours.
To disable this setting, follow the steps in (See “Auto Power 
OFF Function” on p. 5-6).
Power Switch 
						

							Chapter 3   Basic Operation
1. Documents....................................................... 3-2Acceptable Documents .........................................3-2
Long Document Mode Setting...............................3-32. Document Feed and Eject Trays ..................... 3-5Preparing the Document Feed Tray ......................3-5
Adjusting the Document Guides............................3-7
Preparing the Document Eject Tray ......................3-93. Document Feeding Methods.......................... 3-10Selecting the Document Feeding Method ...........3-104. Scanning ........................................................ 3-13About the Job Function .......................................3-13
CapturePerfect 3.1 ..............................................3-145. Using Patchcode Sheets (Option) ................. 3-19About Patchcode Sheets.....................................3-19
How to Use Patchcode Sheets ...........................3-206. Handling Interruptions in Scanning ................ 3-22Check Error Message on Control Panel..............3-22
Handling Paper Jams, Skewed Documents, 
and Staples .........................................................3-22
Handling a Double Feed .....................................3-23