Canon scanner imageFORMULA CR80 User Manual

							51
AHook your finger around the open lever and open the 
Maintenance Cover.
BRemove the Imprinter Cover.
CSqueeze in both sides of the print position adjustment lever 
and move the print cartridge carriage to its lowest position.
DPush back the ink cartridge lock lever in the direction of the 
arrow in the diagram below, and pull out the ink cartridge by 
grasping the tab as shown in the diagram.
CAUTION
Do not touch the ink jet nozzle right after imprinting. The nozzle may be 
very hot. 
						

							52
ESet the ink cartridge.For more information, see “Setting the Ink Cartridge and 
Adjusting the Print Position,” on p. 24.
FCarefully replace the Imprinter Cover.
GGently close the Maintenance Cover until it clicks into place.
Adjusting the Separation Roller Gap
If double feed should occur too often, adjust the Separation Roller gap 
according to the following procedure.
IMPORTANT
Make sure that the size, thickness, and weight of your document meets the 
conditions of this scanner. See “Document,” on p. 33.
Your unit has been carefully adjusted to meet most conditions. However, 
the below adjustment may be needed depending on your environment 
(humidity, temperature, etc.) and the documents you are scanning 
(checks, etc.). Perform the adjustment only if necessary.
AHook your finger around the open lever and open the 
Maintenance Cover. 
						

							53
BPull out the document feed tray.
CLoad two checks or check-stock paper together.
DSlide the two sheets through between the feeding roller and 
the separation roller and stop at the position shown below.
NOTE
If you were unable to slide both sheets through the gap between the rollers, 
turn the paper thickness adjustment dial counter-clockwise (left) until both 
sheets two pieces easily slide through the gap.
EGently remove one of the sheets.
Separation Roller
Feeding Roller
Paper Thickness 
Adjustment Dial
Two Sheets 
						

							54
FAdjust the gap between the feeding roller and the separation 
roller to optimum width.
While one sheet remains in place between the rollers, 
continuously attempt to slide the second sheet (in front of the 
remaining sheet) to the right, back through the roller gap.
Slowly turn the paper thickness adjustment dial clockwise (right) 
just until the second sheet stops feeding into the gap.
IMPORTANT
Turning the Adjustment Dial clockwise too much may damage the rollers.
GRemove the sheets from the paper path and close the 
Maintenance Cover.
HConfirm that the document feeds properly.See “Confirming Proper Document Feeding,” on p. 37.
If additional assistance is required, contact your local authorized 
Canon dealer or service representative.
IPlace a marking label on the unit pointing to the adjustment 
dial as illustrated below. This will serve as a reference point 
for future adjustments if required.
Second sheet does not feed 
into the gap.
Marking labels for thickness 
adjustment dial 
						

							
55
Scanner SpecificationsAC Adapter Specifications
■Use the recommended operating environment for the ink 
cartridge when using the imprinter.
■ You can use the functions noted above if your software 
supports them.
■ These functions may not work depending on your computer’s 
capabilities and the software you are using.
Specifications are subject to change without notice.
Specifications
Type Desktop sheet-through scanner
Document size Height: 50 to 108 mm (2.0 to 4.3)
Length: 80 to 228 mm (3.1 to 9.0)
Thickness: 0.08 to 0.20 mm (0.003 to 
0.008)
0.10 to 0.14 mm (0.004 to 0.006) with 
double feed detection enabled
Weight: 64 to 157 g/m
2 (17 to 40 lb bond)
81 to 105 g/m2 (21.5 to 26.8 lb bond) with 
Double Feed Detection enabled
Document feeding Automatic
Scanning method Contact image sensor (CMOS)
Light source LED
Scanning side Simplex/Duplex
Scanning mode Black-and-white, Fine Text Filtering, Error 
diffusion, 16-Level gray, 256-Level gray, 
24-bit color
Scanning resolution 
(primary scan lines x 
secondary scan lines) Excluding 24-bit color: 100 x 100 dpi, 
200 x 200 dpi, 300 x 300 dpi
24-bit color: 100 x 100 dpi, 200 x 100 dpi
Scanning speed CR-50: 50 cpm (American checks)
CR-80: 80 cpm (American checks)
Automatic feeder capacity Load limit of less than 5 mm (0.2) (within 
the load limit mark)
Automatic document feed 
capacity Up to 50 sheets Interface
Hi-Speed USB 2.0
Other functions Infrared double feed detection
Dimensions 140 mm (W) x 223 mm (D) x 188 mm (H)  
(5.5 (W) x 8.8 (D) x 7.4 (H))
Weight Approximately 2.0 kg (4.4 lb)
Power requirement DC16V 0.8A (excluding AC adapter)
Power consumption Maximum Power: 20.4 W
Sleep Mode: 4.7 W
Power SW OFF: 0.5 W
Noise Less than 65 dB
Operating environment Temperature: 10°C to 32.5°C (50°F to 
90.5°F)
Humidity: 20% to 80% RH (20% to 50% RH 
when using the imprinter)
Input AC 100-240V 50/60Hz 53VA-72VA
Output DC16V 1.4A
Weight Approximately 0.22 kg (0.49 lb) (excluding 
power cord) 
						

							56
Index
A
AC Adapter Specifications ............................................... 55
Adjusting the Print Position .............................................. 24
Amount loaded ................................................................. 35
C
Cleaning
Main unit .................................................................... 45
Cleaning the Inside of the Scanner .................................. 45
Connectors/Power Switch ................................................ 16
D
Daily Cleaning .................................................................. 45
Disposal ........................................................................... 10
Document Eject Opening ................................................. 14
Document Feed Opening ................................................. 14
Document Feed Tray ....................................................... 14
Documents ....................................................................... 33
Document .................................................................. 33
How to place documents ........................................... 35
Double Feed Detection .................................................... 34
E
Eject Stopper ................................................................... 14
Exterior Dimensions ......................................................... 16
F
Features of the CR-50/80 ................................................ 12
Feeding Roller.................................................................. 15
Feeding Trouble ............................................................... 43
H
Handling ............................................................................. 9
I
Imprinter Cover ................................................................. 14
Ink Absorber ..................................................................... 15
Ink Cartridge ......................................................... 15, 24, 50
Ink Jet Nozzle ................................................................... 49
Installation Location .......................................................... 10
L
Lock Lever ........................................................................ 15
M
Magnetic head .................................................................. 48
Magnetic Head for MICR .................................................. 15
Maintenance ..................................................................... 50
Maintenance Cover .......................................................... 14
Moving the Scanner.......................................................... 11
N
Number of pages loaded .................................................. 35
O
Operating Environment..................................................... 18 
						

							57
P
Paper Thickness Adjustment Dial .................................... 14
Power Connector ............................................................. 16
Power Cord ................................................................ 13, 22
Power Indicator ................................................................ 14
Power Supply ................................................................... 11
Power Switch ................................................................... 16
Print Position Adjustment Lever ................................. 15, 51
R
Reading Unit (Access Hatch) ........................................... 16
Recognizing the scanner ................................................. 23
Rollers .............................................................................. 45
S
Scanning Glass ................................................................ 45
Scanning Utility .......................................................... 19, 28
Separation Roller ............................................................. 15
Setup Disc........................................................................ 13
Software
How to Use the Software ........................................... 28
Install ......................................................................... 19
Uninstall ..................................................................... 30
Specifications ................................................................... 55
T
The Scanner Does Not Turn ON...................................... 42
Troubleshooting ............................................................... 40
Turning OFF the Power ................................................... 23
Turning ON the Power ..................................................... 22
U
Unpacking the scanner ..................................................... 13
USB Connections ....................................................... 21, 40
USB Connector................................................................. 16 
						

							CANON ELECTRONICS INC.
1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN
CANON U.S.A. INC.
ONE CANON PLAZA, LAKE SUCCESS, NY 11042, U.S.A.
CANON CANADA INC.
6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA
CANON EUROPA N.V.
BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS
CANON LATIN AMERICA, INC.
703 WATERFORD WAY, SUITE 400, MIAMI, FL 33126, U.S.A.
CANON SINGAPORE PTE. LTD.
1 HARBOUR FRONT AVENUE #04-01, KEPPEL BAY TOWER, SINGAPORE 098632
CANON HONGKONG COMPANY LTD.
19TH FLOOR, THE METROPOLIS TOWER, 10 METROPOLIS DRIVE, HUNGHOM, KOWLOON, HONG KONG.
PUB. CE-IE-836 © CANON ELECTRONICS INC. 2011