Canon Projector WUX10 Mark II User Manual

							41Connecting the Projector
Projecting an Image 
■Connecting to Analog Video Output Terminal (analog connection)
Video cable (Input signal type: [VIDEO] - P49)
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
turns down the sound.
RCA terminal
RCA terminal
Commercial audio cable Mini jackCommercial video cable
To input a corresponding 
audio signal:To VIDEO IN
To AUDIO IN 
Audio output terminal
AV equipmentProjector
Image output 
terminal 
						

							Connecting the Projector
42
Supplied component cable (Input signal type: [COMPONENT] - P49)
A Component video signal from AV equipment can be input to the projector by connect-
ing the supplied component cable to the ANALOG PC-2/COMPONENT IN terminal of the 
projector.
Use a commercial component cable that fits to the terminal type of the AV equipment to 
connect the supplied component cable. 
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
turns down the sound.
RCA terminal
Mini jack
Audio output terminal
To input a corresponding 
audio signal:
Commercial audio cableTo AUDIO IN 
RCA Componentterminal
D terminal
Image output 
terminalCommercial component cable 
with RCA – RCA plugs
Supplied compo-
nent cable
Commercial compo-
nent adapter cable with 
D terminal – RCA plugsTo ANALOG PC-2/
COMPONENT IN AV equipment
Projector 
						

							43Connecting the Projector
Projecting an Image 
■Outputting Audio to Speakers
It is possible to output sound of projected images to AV equipment or amplified speakers. 
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
turns down the sound.
RCA terminal
Mini jack
Audio input terminal
(AUDIO IN)
To AUDIO OUT
Commercial audio cable Projector
Speaker 
						

							44
Starting Projection
1Check the connection between the projector and a computer or AV equipment. (P36 – 
P43)
2Connect the power cord and make sure that the [POWER] indicator lights up red.
Flashing red [POWER] indicator indicates that the lamp is being cooled. Wait until the 
indicator turns a steady red.
 Fully insert the power cord plug into the socket.
 Connect the ground terminal on the power plug to ground. Otherwise, an electric 
shock may result or the computer may suffer electromagnetic radiation problems or 
be subject to poor reception by TV and radio.
 Wait at least 5 minutes before turning on the projector when you turn off the projector.
It may shorten the lamp life if you turn on the projector immediately after turning it off.
 To save power, unplug the power cord when not in use.
3Remove the lens cap and press the POWER button.
The POWER indicator flushes green, and then lights in green.
The countdown window is displayed for approximately 20 seconds, and then the pro-
jection is started. Press the OK button to make the countdown window disappear.
4Turn on the computer or AV equipment power.
Remote controlTop control 
						

							45Starting Projection
Projecting an Image 
5Press the AUTO SET button.
Performs auto adjustment on focusing, keystone distortion, input signal settings, and 
screen color correction. For more details, refer to the page 47.
If the projector is projecting an image properly with [AUTO SETUP], the projection is 
complete.
For how to turn off the projector, refer to the page 64. Perform the appropriate opera-
tion depending on the following situations.
■When the Language Selection Screen Appears
A window appears when the projector is turned on for the first time. You can select a lan-
guage to be used by the projector for displaying menus and messages in the window. 
Select the desired language with the pointer buttons and press the OK button.
You can change the language from the menu at a later time. (P98)
If the language selection screen is out of focus, press the FOCUS and then AUTO SET 
buttons to make focus adjustment.
Changing Operations When Projector is Turned On
You can change operations when the projector is turned on as follows:
 You can turn on the projector by connecting the power cord without pressing the 
POWER button. (P96)
 You can specify whether to enable or disable the LED illumination lamp. (P99)
 You can change the countdown window. (P85)
 You can skip the countdown window. (P44)
Using the Power Saving Mode (power management)
When you enable the power management mode, the lamp is automatically turned 
off if the projector receives no signal input for a certain period of time. (P95)
An item highlighted in orange will be selected.
Remote controlTop control 
						

							Starting Projection
46
■When the Password Input Screen Appears
If you have set a password, the Password input screen appears. Enter your password. 
(P100)
■When No signal Appears
A notebook computer requires to turn on the external monitor output. (P46)
Press the INPUT button to select an appropriate input signal. (P50)
■When Notebook Computer Screen Does Not Appear
Set your notebook computer to output signals to an external monitor. For more details, 
refer to Changing Notebook Computer Screen Output below.
■Adjusting Image
 For the display resolution of the computer, select 1920 x 1200 pixels or a resolution 
closest to the output signal resolution of the computer. (P51)
 Use the auto PC function to adjust shift in computer image or the flickering of the 
screen. (P52)
Use the ZOOM button to adjust the size of the projecting image. (P53)
Use the FOCUS button to correct the focus adjustment if necessary. (P54)
 Use the D.SHIFT/KEYSTONE button to adjust keystone correction if necessary. (P55)
 Select the aspect ratio of the projecting image (screen aspect) or a screen mode 
(aspect) according to the aspect ratio of the screen, type of input image signal and so 
on. (P57 - P62)
 Select an image mode depending on the projecting image. (P63)
Changing Notebook Computer Screen Output
To use a notebook computer, you need to change the screen output on the notebook 
computer.
This operation is not required for a desktop computer.
■Turning On External Monitor Output
You can turn on the external monitor output via keyboard operation.
To turn on the external monitor output, press an icon for an external monitor or a function 
key ([F1] to [F12]) while holding [Fn] key down.
The function keys you use and the method used to turn on the external monitor output vary 
depending on the model. For details, see the instructions of your notebook computer.
While holding   keyPress a key such as   or  
						

							47
Projecting an Image 
Setting Up the Screen Automatically
Auto Setup
The auto setup function automatically makes the following settings and adjustments.
Use the auto setup function when:
 You turned the power on and the countdown sequence was completed.
 You changed the position or angle of the projector during the projection process. Setting image input signal (Auto input)
Focusing (Auto focus)
Keystone correction (Auto keystone)
Screen color correction (Auto screen color correction)
 The auto screen color correction is disabled at the factory. To enable the auto screen color 
correction when performing the auto setup, select the function in menu. (P82)
 You cannot set a digital PC signal or an AV equipment signal ([Digital PC] and [HDMI]) 
with the auto setup function. Select the appropriate signal by pressing the INPUT button. 
(P50)
 When No signal message appears, press the INPUT button to select an appropriate 
input signal. (P50)
 If focusing, keystone distortion and/or screen color correction have not been performed 
properly, manually adjust them. (Adjusting the focus: P54, Correcting keystone distortion: 
P55 and Correcting the screen color: P82)
 If you select [16:9 D. image shift] or [4:3 D. image shift] for [Screen aspect], [Auto setup] 
will be disabled and the following screen appears.
 When you press the INPUT button and then the AUTO SET button, only the input signal 
type is set.
 When you press the FOCUS button and then the AUTO SET button, only the focus is 
adjusted. If you select [16:9 D. image shift] or [4:3 D. image shift] for [Screen aspect], the 
auto focus function will be disabled.
 When you press the D.SHIFT/KEYSTONE button and then the AUTO SET button, only the 
keystone distortion is adjusted. If you select [16:9 D. image shift] or [4:3 D. image shift] for 
[Screen aspect], the keystone adjustment will be disabled.
The keystone adjustment is not performed under the some other conditions. For the 
details, refer to the page 56. 
						

							Setting Up the Screen Automatically
48
■Performing the Auto Setup
Press the AUTO SET button to perform the auto setup.
 After the auto setup is complete, the following window appears. Press the OK button.
Remote controlTop control 
						

							49
Projecting an Image 
Selecting an Input Signal (INPUT)
Select an appropriate input signal in the [INPUT] menu if you want to project a digital PC or 
AV equipment signal or you connect multiple computers or AV equipment to receive their 
input signals.
Skip this step if you have not changed the input signal since the last projection.
■Types of Input Signals
The table below shows the relationship among input signals supported by the projector, 
input terminals and connection cables.
Input signal Input terminal Types of connection cables
HDMIHDMI INHDMI cable (commercial item)
DIGITAL PCANALOG PC-1/
DVI-I INDVI digital cable (LV-CA29, option)
ANALOG PC-1ANALOG PC-1/
DVI-I INComputer connection cable (supplied item)
ANALOG PC-2ANALOG PC-2/
COMPONENT INVGA cable (commercial item)
BNC cable (commercial item)
COMPONENTANALOG PC-2/
COMPONENT INComponent cable (supplied item)
VIDEOVIDEO INVideo cable (commercial item)
Commercial 
BNC cable mini D-sub 15-pin - BNC 
Terminal Convert Cable 
(commercial item)
Commercial component 
adapter cable with 
D terminal – RCA plugs
Commercial component 
cable with RCA-RCA plugs 
						

							Selecting an Input Signal (INPUT)
50
■Selecting an Input Signal
1Press the INPUT button to pop up a window shown at the lower right.
The currently active input signal is marked with a circle and highlighted in orange.
An input signal that is ready for projection is displayed in white. When no signal is 
received, it is displayed in gray. [HDMI], [DIGITAL PC], and [ANALOG PC-1] may be 
displayed in gray even if they are ready for projection.
2The selection is toggled through available input signal types by pressing the INPUT 
button.
 You can select the target input signal with [ ] / [ ].
 Only the input signals displayed in white can be selected.
3Press the OK button to determine the input signal type.
If no button is pressed in 4 seconds, the selected input signal type is chosen.
Remote controlTop control