Canon Projector WUX10 Mark II User Manual

							91Setting the Image Quality
Setting Up Functions from Menus
Making Advanced Adjustment (Dynamic 
gamma)
[Advanced adjustment] - [Dynamic gamma]
You can adjust the gradation representa-
tion of light and dark portions of an image 
automatically.
Press the OK button to accept your setting 
and then press the MENU button.
 The adjustment you have made is 
stored as an adjusted value of input sig-
nals being projected in an image mode.
Making Advanced Adjustment (Auto flesh-
tone)
[Advanced adjustment] - [Auto fleshtone]
You can represent the skin color impres-
sively.
Press the OK button to accept your setting 
and then press the MENU button.
 The adjustment you have made is 
stored as an adjusted value of input sig-
nals being projected in an image mode.
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OffDynamic gamma is disabled.
WeakDynamic gamma is used a little.
StrongDynamic gamma is used to a large 
extent.
Advanced adjustment
Image adjustment
Dynamic gamma
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OffDisables the [Auto fleshtone] function.
L
M
HSpecifies the intensity of the [Auto flesh-
tone] in three steps.
Advanced adjustment
Image adjustment
Auto fleshtone 
						

							Setting the Image Quality
92
Adjusting Fine Color Adjustment (6-axis 
color adjust)
[Advanced adjustment] - [6-axis color adjust]
You can make fine color adjustment with 
RGB (red, green, blue) and CMY (cyan, 
magenta, yellow). For the details of 6-axis 
color adjust, refer to the page 135.
When you have completed the adjust-
ment, press the MENU button.
 [Off] is the factory default.
 The adjustment you have made is 
stored as an adjusted value of input sig-
nals being projected in an image mode.
Correcting the Image According to the 
Ambient Light
[Ambient light]
You can correct and project an image 
more appropriately according to the ambi-
ent light on the screen if you have 
selected [Photo] for [Image mode].
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OffDisables the 6-axis color adjustment.
If you select [Adjust], the previous set-
ting of 6-axis color adjustment 
becomes active again.
AdjustEnables the 6-axis color adjustment.
Use [ ] / [ ] to select [  Hue] or [  
Saturation], then adjust them with [].
ResetReturns any adjustment values to zero.
Advanced adjustment
Image adjustment
6-axis color adjust

						

							93Setting the Image Quality
Setting Up Functions from Menus
An Example of the Ambient Light Setting
Press the OK button to accept your setting 
and then press the MENU button.
 [Off] is the factory default.
 You can set this if you have selected 
[Photo] for [Image mode].
Reducing the Lamp Brightness
[Lamp mode]
Reducing the lamp brightness reduces 
power consumption and cooling fan noise. 
You can enable or disable this mode also 
with the LAMP button on the remote con-
trol.
Press the OK button to accept your setting 
and then press the MENU button.
 [Normal] is the factory default.
 The setting you have made is stored as 
a setting value of input signals being 
projected in an image mode.
Level LSelect this if the ambient light 
source is a light bulb or bulb color 
fluorescent.
MSelect this if the ambient light 
source is a day white fluorescent.
HSelect this if the ambient light 
source is a daylight fluorescent.
LevelExample Location
LA projection room, bar
MPhoto studio, galley
HConference room, lecture room
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
NormalProjects an image at the normal bright-
ness level.
QuietReduces the lamp brightness and cool-
ing fan noise.
Lamp mode
Image adjustment 
						

							Setting the Image Quality
94
Resetting the Image Settings
[Reset]
You can reset the current image settings to 
the default settings.
Press the OK button to accept your setting 
and then press the MENU button.
 Only the setting of the combined input 
signals being projected and an image 
mode is reset.
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OKResets the image settings.
CancelCancels resetting of the image set-
tings.
Reset
Image adjustment 
						

							95
Setting Up Functions from Menus
Setting Various Function
Setting Auto Setup Function
[Auto setup]
You can select an items you want to 
enable in the auto setup function.
Select [On] for the items if you want to 
enable in auto setup function.
Press the OK button to accept your setting 
and then press the MENU button.
 The factory default settings are as fol-
lows:
[Auto focus]: [On]
[Auto keystone]: [On]
[Auto input]: [On]
[Auto screen color]: [Off]
 You cannot change any items in [Auto 
setup] if [16:9 D. image shift] or [4:3 D. 
image shift] is selected for [Screen 
aspect]. In addition, you cannot perform 
the auto setup function. For the details 
of the [Auto setup], refer to the page 47.
Selecting the Power Management Mode
[Power management mode]
You can turn off the lamp or projector auto-
matically for saving power.
Press the OK button to accept your setting 
and then press the MENU button.
 [Off] is the factory default.
 The POWER indicator flashes red and 
green when the projector is in the 
[Standby] power management mode.
 You cannot enable the [Direct power on] 
function (see the next item), if you select 
[Off].
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
Auto focusEnables the auto focusing.
Auto keystoneEnables the auto keystone cor-
rection.
Auto inputEnables the auto input selec-
tion.
Auto screen 
colorAdjusts color quality of images 
corresponding to the color of 
the projection screen.
Auto setup
System settings
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OffDisables the power management 
mode.
StandbyIf no input signal is received for 30 
seconds, the projector enters the 
standby mode, turning off the lamp 
five minutes after start of countdown.
If it receives the input signal or is oper-
ated during such period of 30 sec-
onds, it resumes projection.
ExitIf no input signal is received for 30 
seconds, it displays the count down 
and turns off the projector after 5 min-
utes.
Power management mode
System settings 
						

							Setting Various Function
96
Skip the POWER Button Operation
[Direct power on]
You can turn on the projector only by con-
necting the power cable without pressing 
the POWER button.
Press the OK button to accept your setting 
and then press the MENU button.
 [Off] is the factory default.
Enabling/Disabling the Beep
[Beep]
You can select whether a beep sounds or 
not when you operate the projector.
Press the OK button to accept your setting 
and then press the MENU button.
 [On] is the factory default.
 It does not beep if you mute the projec-
tor sound with the MUTE button on the 
remote control.
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OffYou need to press the POWER button to 
turn on the projector.
OnYou can turn on the projector only by 
connecting the power cable.
 Before setting the direct power-on to 
[On], be sure to set the [Power man-
agement mode], described on the 
preceding page, to [Standby] or 
[Exit].
 Wait at least 5 minutes when you 
power on the projector again after 
disconnecting it. It may shorten the 
lamp life if you turn on the projector 
immediately after turning it off.
Direct power on
System settings
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OffDisables the beep.
OnEnables the beep.
Beep
System settings 
						

							97Setting Various Function
Setting Up Functions from Menus
Prohibiting the Projector Operation
[Key lock]
You can prohibit the operation of the projector 
from either the top control or remote control.
Press the OK button to accept your setting 
and then press the MENU button.
 [Off] is the factory default.
Setting up the Remote Control Channel 
[Remote control]
You can set different channels to different 
remote controls, if you use two projectors 
at the same time.
Press the OK button to accept your setting 
and then press the MENU button.
 The factory defaults is [Ch1] for both 
projector and remote control.
 After changing the channel on the 
menu, be sure to change the channel of 
the remote control, too.
Selecting a Channel on the Remote Control
You can change the channel on the 
remote control as follows:
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OffDisables the key lock.
Main unitProhibit the operation from the 
main unit.
Use the remote control.
Remote 
controlProhibit the operation from the 
remote control.
Use the main unit.
The key lock function becomes effective 
from the moment the OK button is 
pressed after selecting [Main unit] or 
[Remote control]. Be sure to press the 
OK button on the top control or remote 
control which is not locked.
Key lock
System settings
To Unlock Key Lock Function
Turn off the projector and unplug the power 
plug. Hold down the OK button on the top 
control and connect the power plug. Make 
sure to keep holding down the OK button 
until a beep sounds. The key lock is 
unlocked.
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
Ch1Select the channel of the remote control 
used for this projector, and press the OK 
button. Ch2
Ch1Press the OK button and [ ] for 3 sec-
onds at the same time.
Ch2Press the OK button and [>] for 3 sec-
onds at the same time.
Remote control
System settings
< 
						

							Setting Various Function
98
Selecting a Display Language
[Language]
You can select the language in which the 
menu is displayed.
Use [ ] / [ ] / [] to select the lan-
guage to be used in the menu, then press 
the OK button.
When the setting is completed, press the 
MENU button.
Showing/hiding the Guide Screen
[Guide]
You can select whether to show or hide the 
guide screen which explains operations.
Press the OK button to accept your setting 
and then press the MENU button.
 [On] is the factory default.
 The guide screen is shown when:
- Power is turned off by pressing the 
POWER button (P64).
- No input signal can be detected 
(P46).
- An invalid button is pressed in the 
[BLANK], [FREEZE], or [D.ZOOM] 
mode (P66, 68).
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
English
Germany
French
Italian
Spanish
Portuguese
Swedish
Russian
Dutch
Finnish
Norwegian
Tu r k i s h
Polish
Hungarian
Czech
Danish
Arabic
Chinese (Simplified)
Chinese (Traditional)
Korean
Japanese
Language
System settings

						

							99Setting Various Function
Setting Up Functions from Menus
Turning on/off LED Illumination
[LED illumination]
You can select whether to enable or dis-
able the LED illumination (P28).
Press the OK button to accept your setting 
and then press the MENU button.
 [On] is the factory default.
 LED illumination is unrelated to turning 
on/off of the POWER or WARNING 
lamp.
Extending the Menu Display Time
[Other settings] - [Menu display time]
You can extend the menu display time, 
which is 30 seconds usually, to 3 minutes.
Press the OK button to accept your setting 
and then press the MENU button.
 [Normal] is the factory default.
 The following display and operation are 
also changed.
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
OffDisables the LED illumination.
OnEnables the LED illumination.
LED illumination
System settings
HDMICOMPONENT
DIGITAL PCVIDEO
ANALOG PC
NormalThe menu is displayed for 30 seconds.
ExtendedThe menu is displayed for 3 minutes.
Item [Normal][Extended]
The display time of the following 
screens
 INPUT (P50)
 Zoom adjustment (P53)
 Focus adjustment (P54)
 Keystone adjustment (P55)
 Keystone reset (P56)
 D.image shift adjustment (P59, P60)
 D.image shift reset (P60)
 Aspect (P62)
 Image mode (P63)
 Volume adjustment (P67)
 Lamp mode (P93)4 to 10
seconds3 
minutes
The pointer buttons holding 
operation other than in [Zoom 
adjustment] and [Focus adjustment].
Enabled Disabled
The VOL button holding operation.
The D.ZOOM button holding 
operation.
Beep at end of [Auto setup] (P48)No Yes
Other settings
System settings
Menu display time 
						

							Setting Various Function
100
Setting a Password
[Other settings] - [Password settings]
Disables the projector unless the correct pass-
word is entered.
Press the OK button to accept your setting and 
then press the MENU button.
 [Off] is the factory default.
 You cannot set [On] unless you have com-
pleted [Register password].
Once you set a password, the password entry 
screen appears at power-on.
Enter a 4-digit password with [ ] / [ ] / [].
If the password is valid, the projection starts. If 
you enter a wrong passwords three times, the 
power will be turned off.
 The power is also turned off if no password is 
inputted for 3 minutes.
Registering a Password
[Other settings] - [Register password]
You can register a password for starting 
projection.
Press the OK button after selecting [Reg-
ister password], and the following screen 
for registering a password appears:
Enter a 4-digit password using [ ] / [] (e.g.,  ,