Canon Projector SX80 Mark II User Manual
Here you can view all the pages of manual Canon Projector SX80 Mark II User Manual. The Canon manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 41
![Page 41
41Connecting the Projector
Projecting an Image
Commercial or supplied VGA cable (Input signal type: [ANALOG PC-2] - P54)
If you use a commercial VGA cable, make sure to use a full connected VGA cable in
which all pins are connected; otherwise, an image may be projected improperly.
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
Monitor output
terminal
(mini D-sub 15-pin)
Audio output terminal
(AUDIO OUT)
To input a corresponding...](http://img.usermanuals.tech/thumb/14/99167/w300_projector_manual_5016_d-40.png "Page 41
41Connecting the Projector
Projecting an Image
Commercial or supplied VGA cable (Input signal type: [ANALOG PC-2] - P54)
If you use a commercial VGA cable, make sure to use a full connected VGA cable in
which all pins are connected; otherwise, an image may be projected improperly.
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
Monitor output
terminal
(mini D-sub 15-pin)
Audio output terminal
(AUDIO OUT)
To input a corresponding...")
41Connecting the Projector Projecting an Image Commercial or supplied VGA cable (Input signal type: [ANALOG PC-2] - P54) If you use a commercial VGA cable, make sure to use a full connected VGA cable in which all pins are connected; otherwise, an image may be projected improperly. Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. Monitor output terminal (mini D-sub 15-pin) Audio output terminal (AUDIO OUT) To input a corresponding...
Page 42
![Page 42
Connecting the Projector
42
■Connecting to DVI Monitor Output Terminal (digital connection) (SX80 II)
DVI cable (Input signal type: [DIGITAL PC] - P54)
■Outputting an Image and Audio
Outputting an Image (SX80 II)
Images can be output to an external monitor via [ANALOG PC-1], [ANALOG PC-2] and
[COMPONENT].
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
You can connect one external monitor.
It outputs an image of the analog PC or...](http://img.usermanuals.tech/thumb/14/99167/w300_projector_manual_5016_d-41.png "Page 42
Connecting the Projector
42
■Connecting to DVI Monitor Output Terminal (digital connection) (SX80 II)
DVI cable (Input signal type: [DIGITAL PC] - P54)
■Outputting an Image and Audio
Outputting an Image (SX80 II)
Images can be output to an external monitor via [ANALOG PC-1], [ANALOG PC-2] and
[COMPONENT].
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
You can connect one external monitor.
It outputs an image of the analog PC or...")
Connecting the Projector 42 ■Connecting to DVI Monitor Output Terminal (digital connection) (SX80 II) DVI cable (Input signal type: [DIGITAL PC] - P54) ■Outputting an Image and Audio Outputting an Image (SX80 II) Images can be output to an external monitor via [ANALOG PC-1], [ANALOG PC-2] and [COMPONENT]. Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. You can connect one external monitor. It outputs an image of the analog PC or...
Page 43
43Connecting the Projector Projecting an Image Outputting Audio to Speakers It is possible to output sound of projected images to AV equipment or amplified speakers. The speaker outputs the audio signal corresponding to the selected image signal. Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. To AUDIO OUT Commercial audio cable Audio input terminal (AUDIO IN) ProjectorSpeaker RCA terminal Mini jack
Page 44
![Page 44
Connecting the Projector
44
Connecting to AV Equipment
Connect the projector and AV equipment.
Before connecting the cables, turn off both the projector and AV equipment.
The description provided here is just examples. For more detailed information, refer to the
manual for the connecting AV equipment.
■Connecting to Digital Video Output Terminal (digital connection) (SX80 II)
HDMI cable (Input signal type: [HDMI] - P54)
Digital video camera
Digital video
output terminal
(HDMI terminal)Commercial HDMI...](http://img.usermanuals.tech/thumb/14/99167/w300_projector_manual_5016_d-43.png "Page 44
Connecting the Projector
44
Connecting to AV Equipment
Connect the projector and AV equipment.
Before connecting the cables, turn off both the projector and AV equipment.
The description provided here is just examples. For more detailed information, refer to the
manual for the connecting AV equipment.
■Connecting to Digital Video Output Terminal (digital connection) (SX80 II)
HDMI cable (Input signal type: [HDMI] - P54)
Digital video camera
Digital video
output terminal
(HDMI terminal)Commercial HDMI...")
Connecting the Projector 44 Connecting to AV Equipment Connect the projector and AV equipment. Before connecting the cables, turn off both the projector and AV equipment. The description provided here is just examples. For more detailed information, refer to the manual for the connecting AV equipment. ■Connecting to Digital Video Output Terminal (digital connection) (SX80 II) HDMI cable (Input signal type: [HDMI] - P54) Digital video camera Digital video output terminal (HDMI terminal)Commercial HDMI...
Page 45
![Page 45
45Connecting the Projector
Projecting an Image
■Connecting to Analog Video Output Terminal (analog connection)
Video cable (Input signal type: [VIDEO] or [S-VIDEO] - P54)
Connect the projector and AV equipment using a video or S-VIDEO cable that fits to the
terminal type of the AV equipment.
The input signal type is [VIDEO] or [S-VIDEO].
Sound is common to [VIDEO] and [S-VIDEO].
[S-VIDEO] is supported only in SX80 MarkII.
Use an audio cable without a built-in resistor. Using an audio cable with a...](http://img.usermanuals.tech/thumb/14/99167/w300_projector_manual_5016_d-44.png "Page 45
45Connecting the Projector
Projecting an Image
■Connecting to Analog Video Output Terminal (analog connection)
Video cable (Input signal type: [VIDEO] or [S-VIDEO] - P54)
Connect the projector and AV equipment using a video or S-VIDEO cable that fits to the
terminal type of the AV equipment.
The input signal type is [VIDEO] or [S-VIDEO].
Sound is common to [VIDEO] and [S-VIDEO].
[S-VIDEO] is supported only in SX80 MarkII.
Use an audio cable without a built-in resistor. Using an audio cable with a...")
45Connecting the Projector Projecting an Image ■Connecting to Analog Video Output Terminal (analog connection) Video cable (Input signal type: [VIDEO] or [S-VIDEO] - P54) Connect the projector and AV equipment using a video or S-VIDEO cable that fits to the terminal type of the AV equipment. The input signal type is [VIDEO] or [S-VIDEO]. Sound is common to [VIDEO] and [S-VIDEO]. [S-VIDEO] is supported only in SX80 MarkII. Use an audio cable without a built-in resistor. Using an audio cable with a...
Page 46
![Page 46
Connecting the Projector
46
Supplied component cable (Input signal type: [COMPONENT] - P54)
A Component video signal from AV equipment can be input to the projector by connect-
ing the supplied component cable to the ANALOG PC-2/COMPONENT IN terminal of the
projector.
Use a commercial component cable that fits to the terminal type of the AV equipment to
connect the supplied component cable.
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the...](http://img.usermanuals.tech/thumb/14/99167/w300_projector_manual_5016_d-45.png "Page 46
Connecting the Projector
46
Supplied component cable (Input signal type: [COMPONENT] - P54)
A Component video signal from AV equipment can be input to the projector by connect-
ing the supplied component cable to the ANALOG PC-2/COMPONENT IN terminal of the
projector.
Use a commercial component cable that fits to the terminal type of the AV equipment to
connect the supplied component cable.
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the...")
Connecting the Projector 46 Supplied component cable (Input signal type: [COMPONENT] - P54) A Component video signal from AV equipment can be input to the projector by connect- ing the supplied component cable to the ANALOG PC-2/COMPONENT IN terminal of the projector. Use a commercial component cable that fits to the terminal type of the AV equipment to connect the supplied component cable. Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the...
Page 47
47Connecting the Projector Projecting an Image ■Outputting Audio to Speakers It is possible to output sound of projected images to AV equipment or amplified speakers. Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. RCA terminal Mini jack Audio input terminal (AUDIO IN) To AUDIO OUT Commercial audio cable Projector Speaker
Page 48
Connecting the Projector 48 ■Connecting a Digital Camera or an USB Flash Memory (SX80 II) SX80 MarkII supports PictBridge. You can connect a PictBridge enabled digital camera, a digital video camera, an USB flash memory, or an USB memory card reader to directly project images. Digital camera USB memory card readerUSB flash memory USB cable (recommended by digital camera manufacturer) USB cable (supplied with memory card reader)To USB terminalProjector Digital video camera Digital camera USB flash...
Page 49
![Page 49
49
Projecting an Image
Starting Projection
1Check the connection between the projector and a computer or AV equipment. (P38 –
P48)
2Connect the power cord and make sure that the [POWER] indicator lights up red.
Flashing red [POWER] indicator indicates that the lamp is being cooled. Wait until the
indicator turns a steady red.
Fully insert the power cord plug into the socket.
Connect the ground terminal on the power plug to ground. Otherwise, an electric
shock may result or the computer may suffer...](http://img.usermanuals.tech/thumb/14/99167/w300_projector_manual_5016_d-48.png "Page 49
49
Projecting an Image
Starting Projection
1Check the connection between the projector and a computer or AV equipment. (P38 –
P48)
2Connect the power cord and make sure that the [POWER] indicator lights up red.
Flashing red [POWER] indicator indicates that the lamp is being cooled. Wait until the
indicator turns a steady red.
Fully insert the power cord plug into the socket.
Connect the ground terminal on the power plug to ground. Otherwise, an electric
shock may result or the computer may suffer...")
49 Projecting an Image Starting Projection 1Check the connection between the projector and a computer or AV equipment. (P38 – P48) 2Connect the power cord and make sure that the [POWER] indicator lights up red. Flashing red [POWER] indicator indicates that the lamp is being cooled. Wait until the indicator turns a steady red. Fully insert the power cord plug into the socket. Connect the ground terminal on the power plug to ground. Otherwise, an electric shock may result or the computer may suffer...
Page 50
![Page 50
Starting Projection
50
5Press the AUTO SET button.
The auto setup function performs the following operations automatically:
SX80 MarkII: focusing and keystone distortion adjustment, input signal setting, and
screen color correction
SX800: keystone distortion adjustment and input signal setting
For more details, refer to the page 52.
If the projector is projecting an image properly with [AUTO SETUP], the projection is
complete.
In SX800, adjust the focus and correct the screen color manually.
For how...](http://img.usermanuals.tech/thumb/14/99167/w300_projector_manual_5016_d-49.png "Page 50
Starting Projection
50
5Press the AUTO SET button.
The auto setup function performs the following operations automatically:
SX80 MarkII: focusing and keystone distortion adjustment, input signal setting, and
screen color correction
SX800: keystone distortion adjustment and input signal setting
For more details, refer to the page 52.
If the projector is projecting an image properly with [AUTO SETUP], the projection is
complete.
In SX800, adjust the focus and correct the screen color manually.
For how...")
Starting Projection 50 5Press the AUTO SET button. The auto setup function performs the following operations automatically: SX80 MarkII: focusing and keystone distortion adjustment, input signal setting, and screen color correction SX800: keystone distortion adjustment and input signal setting For more details, refer to the page 52. If the projector is projecting an image properly with [AUTO SETUP], the projection is complete. In SX800, adjust the focus and correct the screen color manually. For how...