Canon Projector SX6000 User Manual

161
Setting Up the Projector
Installation Manual InstallationArea where lens movement is not possible
With the Standard Zoom Lens, Long Zoom Lens and Ultra Long Zoom Lens, when the 
shift exceeds 44% in the upward direction, the amount of available shift in the left / right 
directions decreases. When the lens is shifte d upward to the maximum (1), the amount of 
available shift in the left  / right direction is ±2%.
With the Short Fixed Lens, great er shift in the up / down direction reduces the...

162
Connecting to AV Equipment
■Connectable Equipment and Input Terminals
Computer (P49)AV equipment (P52)
Digital video camera* (P52) Computer (P47, P49)
AV equipment (P53)
(P166)
(P47, P49, 
P53)
(P50)(P51, P55) Computer (P51)
* Select play-
back mode be-
fore connecting.
Analog PC / ComponentDigital PC
ANALOG PC / COMPO-
NENT IN terminalDVI-D IN terminalHDMI IN terminal
LAN terminal
Service port (not 
normally used)AUDIO IN terminal
AUDIO OUT terminal
NetworkAudio signal for each 
image input
Analog...

163
Connecting to AV Equipment
Installation Manual Installation
Computer (P49)AV equipment (P52)
Digital video camera* (P52) Computer (P48, P49)
AV equipment

	1

(P166)
(P48, P49, 
P54)
(P50)(P51, P55) Computer
 (P51)
(P30) Analog PC-1
ComponentAnalog PC-2
Digital PCHDMI
ANALOG PC-1 / COM-
PONENT IN terminalANALOG PC-2 / DVI-D IN 
terminalHDMI IN terminal
DVI-I IN terminal can only 
be used to connect to a 
PC.
* Select play-
back mode be-
fore connecting.
LAN terminal
Remote terminalAUDIO IN...

Connecting to AV Equipment
164
■Connection Terminal and Connection Cable
Input 
signalSupported 
projectorsInput terminal Types of connection cables
HDMIWUX5000
WUX4000
WX6000
SX6000HDMI cable (not included)
Digital 
PCWUX5000
WUX4000DVI cable (not included)
WX6000
SX6000

Analog 
PC
Analog 
PC-1WUX5000
WUX4000
WX6000
SX6000 / 
COMPONENT INVGA cable (supplied)
WUX5000
WUX4000
WX6000
SX6000 / 
COMPONENT INBNC cable (not included)
Analog 
PC-2WX6000
SX6000
VGA-DVI cable (not included)
Compo-
nentWUX5000...

Safety Instructions
Table of Contents
Connecting to a Network
Maintenance
Before Use
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from Menus
Installation
User’s Manual
Appendix
IndexAppendix Installation Manual
165
Connecting to a 
Network 

166
Preparing the Remote Control
If the projector is connected to a network, projector error notification mails can be 
received and the projector can be controlled via a computer. Settings related to the net-
work connection can be made from either the projector side (P172) or computer side 
(P177).
Depending on the method of network connection, preparation on the computer side may 
be necessary. The following is an explanation of preparation on the computer side.
Connection Methods
Connect the...

167
Preparing the Remote Control
Installation Manual Connecting to a Networ
k
Setting an IP Address
Following is an explanation of how to set the PC IP address for each operating system.
■Windows 7
1From the PC [Start] menu, select [Control Panel].
2Click on [Network and Internet Connections], then click on [View network status and 
tasks].
3From the menu on the left side of the window, click on [Change adapter settings].
4Right-click [Local Area Connection], and open [Properties].
5Select [Internet...

Preparing the Remote Control
168
■Windows Vista
1From the PC [Start] menu, select [Control Panel].
2Click on [View network status and tasks].
3From the menu on the left side of the window, click on [Manage network connections].
4Right-click [Local Area Connection], and open [Properties].
5Select [Internet Protocol Version 4 (TCP/IP)] and click the [Properties] button. Make a 
note of the original network settings (IP address, subnet mask, default gateway, etc).
6Select [Use the following IP address] and...

169
Preparing the Remote Control
Installation Manual Connecting to a Networ
k
■Windows XP
1From the PC [Start] menu, select [Control Panel].
2Select [Network and Internet Connections] and open [Network Connections].
3Right-click [Local Area Connection], and open [Properties].
4Select [Internet Protocol (TCP/IP)] and click the [Properties] button. Make a note of 
the original network settings (IP address, subnet mask, default gateway, etc).
5Select [Use the following IP address] and set the IP address and...

Preparing the Remote Control
170
■Mac OS X
1Open the Apple Menu and select [System Preferences].
2In the System Preferences window, click [Network] to display the Network window.
3Select [Built-in Ethernet] and click the [TCP/IP] tab. Make a note of the original net-
work settings (IP address, subnet mask, router, DNS server, etc.).
4 Create a new network environment and set the IP address and subnet mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP 
address which is...