Canon Projector LX-MU500 User Manual

51
ENGLISH
Supervising and controlling by computer
With a proper LAN cable connection and LAN Control settings, you can operate the projector from a 
computer using a web browser or PJLink
™ application when the computer and the projector are 
connected to the same local area network.
This projector supports Crestron® software and PJLink™.
An example of connecting the projector to computer.
• When using an external hub or router, use a Category 5 (or above) straight cable. (A crossed 
cable can be used...

52
Controlling the projector remotely through a web browser 
(e-Control
®)
Once you have the correct IP address for the projector and the projector is on or in standby state, you can 
use any computer that is on the same local area network to control the projector.
When using this function, Adobe Flash Player has to be installed in your computer. Please download the 
latest version of Adobe Flash Player from the website of Adobe Systems Incorporated.
Recommended operating systems: WinXP, Win7, Win8.1,...

53
ENGLISH
i. When using the Crestron Control System, please refer to the user manual of Crestron Control 
system for setup information.
ii. You can name the projector, keep track of its location and the person in charge of it. This column 
allows a maximum of 22 single-byte characters.
iii. You can adjust the LAN Settings.
iv. Once set, access to the remote network operation page on this projector has been password-
protected. To enable this function, check the box in front of Enable and type in your...

54
When the projector is in normal conditions or in any abnormal conditions other than the ones 
mentioned below, the Error Status column will be 0:No Error.
(3 = Error)
iii. Press Exit to go back to the remote network operation page.
5. After pressing the button ‘Contact IT Help’, the HELP DESK window will appear at the upper right 
corner. You will be able to deliver messages to RoomView™ software which is connected to the 
same local area network.
For more information, visit http://www.crestron.com &...

55
ENGLISH
PJLink™ supported commands
The table below shows commands to control the projector using the PJLink™ protocol.
• The PJLink INPT? will be replied only when the source is displayed on screen. When there is 
no signal, only ERR3 Time! will be answered.
CommendDescriptionRemark (Parameter)
POWR Power control0 = Power off
1 = Power on
POWR? Inquiry about the power state0 = Standby
1 = Power on
2 = Cooling down
3 = Warming up
INPT Input switching 11 = COMPUTER1
12 = COMPUTER2
21 = VIDEO
22 =...

56
• The above-mentioned control may not be performed correctly or the monitoring data may not 
be obtained correctly in the following conditions:
• During standby
• During input source switching
• During command processing
• During AUTO PC execution
• Before the splash screen disappears after the power is turned on.
• Use 1 computer to control/monitor 1 projector.
• For how to control/monitor using PJLink™, see the operation manual of the PJLink™ 
application you use.
• When you monitor the projectors...

57
ENGLISH
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type selected.
* Indicates an item that is factory-set.
Main menu Sub-menu Options
1. DISPLAY
Screen ColorOff*/Light Yellow/Pink/Light 
Green/Blue/Blackboard
Aspect Auto*/Real/16:10/4:3/16:9
Keystone
Corner Adjustment
Position
Phase
H. Total Dots
D.Zoom
3DAuto*/Frame Sequential/
Frame Packing/Top-Bottom/
Side-By-Side
3D Sync Normal*/Invert
2. PICTURE
Image...

58
* Indicates an item that is factory-set.
Main menu Sub-menu Options
4. 
SYSTEM 
SETUP: Basic
Presentation 
TimerPreset Time 1~240 minutes
Timer Display Always*/1 min/2 min/3 min/Never
PositionTop-Left*/Bottom-Left/Top-Right/
Bottom-Right
Counting 
DirectionCount Down*/Count Up
Sound Reminder On*/Off
On/Off*
Language
Image flip H/VFront Table*/Rear Table/
Front Ceiling/Rear Ceiling
Auto Power OffDisable/5 min/10 min/15 min/
20 min*/25 min/30 min
Blank TimerDisable*/5 min/10 min/15 min/
20 min/25 min/30...

59
ENGLISH
• * Indicates an item that is factory-set.
• The menu items are available when the projector detects at least one valid signal. If there is no 
equipment connected to the projector or no signal detected, limited menu items are accessible. 
Main menu Sub-menu Options
5. 
SYSTEM 
SETUP: 
Advanced
Security SettingsChange Password
Power On Lock On/Off*
Closed Caption 
SettingsClosed Caption On/Off*
Caption Channel CC1*/CC2/CC3/CC4
Serial Port Setting RS232*/HDBaseT
LAN SettingsStandby LAN Off*/On...

60
Description of each menu
FUNCTIONDESCRIPTION
Screen ColorCorrects the projected picture’s color when the projection 
surface is not white. See Using Screen Color on page 44 
for details.
AspectThere are several options to set the images aspect ratio 
depending on your input signal source. See Selecting the 
aspect ratio on page 40 for details.
KeystoneCorrects any keystoning of the image. See Correcting 
keystone on page 39 for details.
Corner AdjustmentCorrects corner distortion of the image. See...