Canon projector LVWX300 User Manual

11
ENGLISH
Precautions for the remote control battery
Caution for viewing 3D content
When handling the lamp, pay attention to the following points.
• Be sure not to handle the lamp immediately after it has been used. Be sure to switch off the power 
and wait for approximately 45 minutes for the lamp and the projector to cool down sufficiently. 
Failure to do so could result in a burn or personal injury due to heat from the lamp or projector.
• When an instruction to replace the lamp has been displayed...

12
For Safe Use
Pay attention to the following points when carrying or transporting the projector.
• This projector is a precision instrument. Do not knock it over or subject it to impacts. Doing so may 
cause a malfunction.
• Do not reuse any packaging or shock-absorbent materials that were supplied with the projector at 
the time of purchase for transporting or shipping the projector. Protection of the projector cannot be 
guaranteed if used packaging or shock-absorbent materials are reused. Fragments...

13
ENGLISH
Contents of package
Projector Power cord 1.8 m (70.8) Computer cable 1.8 m (70.8)
(5K.1VC09.501)
CD & QSG Important Information Warranty card Remote control 
(type number: LV-RC08) 
Battery (type number: CR2025)
(US)
(EU)
(China)
  

14
Projector exterior view
1. External control panel 
(See Projector on page 15 for details.)
2. Lamp cover
3. Vent (heated air exhaust)
4. Quick-release button
5. Focus ring and Zoom ring
6. Front IR remote sensor
7. Projection lens
8. Vent (air intake)
9. Lens cap
10. SERVICE port
11. LAN (RJ-45) port
12. HDMI input terminal
13. PC input terminal x 2
14. CONTROL port
15. Video input terminal
16. S-Video input terminal
17. Audio input terminal
Audio output terminal
18. AC power cord inlet
19. Kensington...

15
ENGLISH
Controls and functions
Projector
7. MENU
Turns on the On-Screen Display (OSD) menu. 
Goes back to previous OSD menu, exits and saves 
menu settings. See Using the menus on page 29 
for details.
8. TEMPerature indicator light
Lights up red if the projectors temperature 
becomes too high. See Indicators on page 65 for 
details.
9. LAMP indicator light
Indicates the status of the lamp. Lights up or 
flashes when the lamp has developed a problem. 
See Indicators on page 65 for details.
10. AUTO...

16
Remote control: LV-RC08
1. POWER (ON/STANDBY)
Toggles the projector between standby mode and 
on. See Starting up the projector on page 28 and 
Shutting down the projector on page 42 for 
details.
2. INPUT
Displays the source selection bar. See Switching 
input signal on page 32 for details.
3. Left
Selects the desired menu items and makes 
adjustments. See Using the menus on page 29 for 
details.
4. BLANK
Used to hide the screen picture. See Hiding the 
image on page 41 for details.
5. TIMER...

17
ENGLISH
Using the remote control for the first time
Pull the tab before using the remote control.
Remote control effective range
Infra-Red (IR) remote control sensor is located on the front of the 
projector. The distance between the  remote control and the sensor 
should not exceed  8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and 
the IR sensor on the projector that  might obstruct the infra-red beam.
• You may not be able to perform operations if there are...

18
Third party software
This product includes third party software modules.
• uIP (micro IP) version 0.9
Please see the below licence text concerning the licence condition.
Copyright © 2001-2003, Adam Dunkels.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided 
that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the 
following disclaimer.
2....

19
ENGLISH
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select. Take into 
consideration the size and position of your screen, the location of a suitable power outlet, as well as the 
location and distance between the projector and the rest of your equipment.
Your projector is designed to be installed in one of the possible installation locations: 
For ceiling mounting, you need the ceiling mount kit to be available...

20
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting (if available), and the video format 
each factors in the projected image size.
4:3 is the native aspect ratio of LV-S300/LV-X300. To be able to project a complete 16:9 (widescreen) 
aspect ratio image, the projector can resize and scale a widescreen image to the projectors native aspect 
width. This will result in a proportionally smaller height equivalent to 75% of the projectors native...