Canon projector LVS3 User Manual

21
Basic Operation
Message disappears after 4 seconds.
Press P-Timer button on the remote control unit.  The timer display
“00 : 00” appears on the screen and the timer starts to count time (00
: 00 ~ 59 : 59).  
To stop P-Timer display, press the P-TIMER button.  And then, press
P-TIMER button again to cancel P-Timer function.
1
2
Press MENU button to display the On-Screen Menu. Press Point
78buttons to move the red frame pointer to SOUND Menu
icon.  Volume
Press VOL (+/–) button on the remote control...

22
Menu Operation Direct Operation
Choose Computer by pressing INPUT button on the top control or
COMPUTER button on the remote control unit.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press the MENU button to display the On-Screen Menu. Press
Point 
7  8buttons to move the red frame pointer to INPUT
Menu icon.
Press Point dbutton to move the red arrow pointer to
Computer and then press SET button. The Source Select Menu
will appear. 
1...

23
Computer Input
Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan
system and Auto PC Adjustment.  If Computer is selected as a signal source, this projector automatically detects the signal
format and tunes to project a proper image without any additional setting.  (Signal formats provided in this projector is
shown on page 49 )
When projector cannot recognize connected signal as PC
system provided in this...

24
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically conform Fine sync, Total dots and Picture Position to your
computer.  This function can be operated as follows.
Press the MENU button to display the On-Screen Menu.  Press
Point 
7  8button to move the red frame pointer to PC Adjust
Menu icon.1
2Press the Point dbutton to move the red frame pointer to Auto
PC Adj. icon and then press the SET button twice.
This Auto PC Adjustment can be also executed by pressing...

25
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector.  In this
case, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-
synchronized picture, a non-centered picture or a skewed picture.
The Manual PC Adjustment function allows you to precisely adjust several parameters to match those special signal
formats. You can store those adjusted parameters in the 5...

26
Computer Input
Note : 
Display area, Display area (H/V) and Full screen cannot be adjusted when
“480p”, “575p”, “480i”, “575i”, “720i (HDTV)” , “1035i (HDTV)” or “1080i
(HDTV)” is selected on PC SYSTEM Menu    ( 
P23 ).
Selects area displayed with this projector.  Select the resolution at
Display area dialog box.Display area
Adjustment of horizontal area displayed with this projector.  Press
Point 
7 8buttons to decrease/increase value to match the
resolution of image. Then press the SET...

27
Computer Input
Move the red frame pointer to the
level and press SET button.
The level being selected.
IMAGE SELECT MENU
Image Select
Menu icon
Direct Operation
Select image level among Standard, High contrast and Custom by
pressing IMAGE button on the remote control unit.
Normal picture adjustment preset on this projector.   Standard
Image Level Selection
User preset image in the Image Adjust Menu (p28). High contrast
Custom
Picture adjustment improved in reproduction of the halftones.  This...

28
Reset all adjustment to previous figure.
Reset
Store
Closes Image Menu.
Quit
To store the image data adjusted manually, move the red frame
pointer to the Store icon and press the SET button. The message
“OK?” will appear.  Select [Yes] to store manual adjustment.
To set this manual adjustment, select Custom by pressing the
IMAGE button or through the Image Select Menu (p27).
Computer Input
Press Point 7 8buttons to
adjust value.
Press MENU button to display the On-Screen Menu.  Press
Point 
7...

29
Computer Input
Screen Size Adjustment
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press MENU button to display the On-Screen Menu.  Press
Point 
7  8buttons to move the red frame pointer to Screen
Menu icon.
When Digital zoom + is selected, the On-Screen Menu disappears
and the message “D. Zoom +” is displayed.  Press SET button to
expand image size.  And press Point 
ed7  8buttons to pan the
image.  The panning function can work only...

30
Input Source Selection ( Video, S-Video )
Menu Operation Direct Operation
Choose Video by pressing INPUT button on the top control or VIDEO
button on the remote control unit.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press MENU button to display the On-Screen Menu.  Press
Point 
7  8buttons to move the red frame pointer to INPUT
Menu icon.
Press Point dbutton to move the red arrow pointer to Video
and then press SET button.  Source...