Canon projector LVS2 User Manual

21
BASIC OPERATION
Press the NO SHOW button on the Remote Control Unit to black out
the image.  To restore to normal, press the NO SHOW button again or
press any other button.
NO SHOW FUNCTION
Message disappears after 4 seconds.
No show
Press the P-TIMER button on the Remote Control Unit.  The timer
display “00 : 00” appears on the screen and the timer starts to count
time (00 : 00 ~ 59 : 59).  
To stop the P-TIMER display, press the P-TIMER button.  Press the P-
TIMER button again to cancel the P-TIMER...

22
COMPUTER INPUT
SELECTING THE INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Choose Computer by pressing the INPUT button on Top Control or on
Remote Control Unit.
If the projector cannot reproduce a proper image, select correct input
source through the MENU OPERATION (see below).
Press the MENU button and the ON-SCREEN MENU will
appear.  Press POINT LEFT/RIGHT button to move the red
frame to the INPUT Menu icon.
Press the POINT DOWN button to move the red arrow to
Computer and then press the SET button....

23
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
This projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100 MHz of
Dot Clock.
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC...

24
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
The Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to
your computer.  Auto PC Adjustment function can be operated as follows.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press POINT LEFT/RIGHT button to move the red
frame to PC ADJUST Menu icon.1
2Press the POINT DOWN button to move the red frame to the
AUTO PC Adj. icon and then press the SET button twice.
This Auto PC...

25
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to the display signals of most personal computers.  However, some computers employ
special signal formats which are different from the standard ones and may not be tuned by the Multi-Scan system of this
projector.  If this happens, projector cannot reproduce a proper image and the image may be displayed as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has Manual PC...

26
COMPUTER INPUT
NOTE :  Display area (H/V) and Full screen cannot be adjusted when
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC
SYSTEM Menu (P22).
Selects the area displayed with this projector.  Select the resolution
at the Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector.  Press the
POINT LEFT/RIGHT button(s) to decrease/increase value to match
the resolution of image.
Display area H
Adjustment of vertical area displayed with this projector....

27
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (MENU)
IMAGE LEVEL SELECT (DIRECT)
Select the image level among Standard, High contrast and Custom by
pressing the IMAGE button on the Remote Control Unit.IMAGE button
Standard
High contrast
Custom
Normal picture adjustment preset on this projector.  
Picture adjustment improved in reproduction of halftones.  This
adjustment is suitable for providing better image in brighter place.
User preset picture adjustment in the IMAGE ADJUST Menu (P28,...

28
COMPUTER INPUT
Press the POINT LEFT/RIGHT but-
tons to adjust value.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to move the red
frame to the IMAGE ADJUST Menu icon.1
2Press the POINT DOWN button to move the red frame to the
item that you want to adjust. and then press the SET button.
The level of each item is displayed.  Adjust each level by the
pressing the POINT LEFT/RIGHT button(s).
Move the red frame to the
item to be selected and then
press the...

29
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button(s) to move the
red frame to the SCREEN Menu icon.
When Digital zoom + is selected, the ON-SCREEN MENU
disappears and the message “D. Zoom +” is displayed.  Press the
SET button to expand image size.  And press the POINT
UP/DOWN/LEFT/RIGHT button(s) to pan the...

30
VIDEO INPUT
SELECTING THE INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Choose Video by pressing the INPUT button on the Top Control or on
the Remote Control Unit.
If the projector cannot reproduce a proper video source, select correct
input source through the MENU OPERATION (see below).
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button to move the red
frame to the INPUT Menu icon.
Press the POINT DOWN button to move the red arrow to Video
and then press the...