Canon projector LVS2 User Manual

VIDEO INY  ––   Pb / Cb  ––  Pr / Cr 
RGB IN
RESET
COMPUTER
AUDIO IN
AV AUDIO IN
AUDIO OUT
S–VIDEO INCONTROL 
11
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
Connect the S-VIDEO
output from your
video equipment to
this jack.  
(Refer to P13.)  
Connect the audio output
(stereo) from the
computer to this jack.
(Refer to P12.)
Connect the audio output
from your video
equipment to this jack.
(Refer to P13.)
COMPUTER AUDIO
INPUT JACKAUDIO INPUT JACK
VIDEO INPUT JACKS
S-VIDEO INPUT JACK
Connect the...

12
CONNECTING THE PROJECTOR
VIDEO IN
RGB IN
RESET
COMPUTER
AUDIO IN
AV AUDIO IN
AUDIO OUT
S–VIDEO INCONTROL 
Y  ––   Pb / Cb  ––  Pr / Cr 
ON
1DIPON
OFF
23456
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF ON ON
ON ON
ON ONOFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF1234 56
OFF OFF ON ON ON ON 21 MODE (1152 x 870)
CONNECTING TO A COMPUTER
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
VGA Cable  Monitor Output
Desktop type Laptop type
Audio Speaker
(stereo) Audio...

13
CONNECTING THE PROJECTOR
CONNECTING VIDEO EQUIPMENT
VIDEO INY  ––   Pb / Cb  ––  Pr / Cr 
RGB IN
RESET
COMPUTER
AUDIO IN
AV AUDIO IN
AUDIO OUT
S–VIDEO INCONTROL 
Video Source (example)
Video Cassette Recorder Video Disc Player
Video Cable
(RCA x 1) ✽S-VIDEO
Cable ✽
Audio AmplifierAudio Speaker (stereo)
Audio Cable 
(Stereo) ✽
Terminals 
of the Projector
Use any of VIDEO jack Y-Pb/Cb-
Pr/Cr jacks or S-VIDEO jack.
•When both VIDEO jack and S-
VIDEO jack are connected, S-
VIDEO jack has priority over...

INPUTPOWER
MUTE
MENU
NO SHOW
AUTOPC ADJ.IMAGE
FREEZE P-TIMER
W
T
D ZOOMKEY
STONE
+
–
VOL
SET
14
BEFORE OPERATION
Battery is installed in Remote
Control Unit.
Before operation, pull out and
remove a protect sheet from
Remote Control Unit. This sheet
protecting discharge of a battery.
FREEZE P-TIMER
BATTERY PROTECT SHEET
(transparent sheet)
Infrared signals transmitted from this point.
To insure safe operation, please observe the following
precautions :
Do not bend, drop Remote Control Unit, or expose...

15
BEFORE OPERATION
Pull out Battery Holder.Replace with new battery. Install
with battery (+),(–) marks properly.Install battery and
Battery Holder into
Remote Control Unit.
BATTERY
LITHIUM BATTERY
CR2025 (3.0V)
(+) mark indicates
its (+) polarity.
Put Battery + mark
as shown direction.
BATTERY HOLDER
REMOTE CONTROL UNIT BATTERY INSTALLATION
To insure safe operation, please observe the following precautions :
Use only specified battery.  Improper battery may cause malfunction of Remote Control Unit....

16
READY
LAMP
REPLACE
LAMP WARNING
TEMP.
INPUT
POWER
SET
KEYSTONE
MENUVOL VOL –+
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
Used to open or close
MENU operation. (P17,
18)
MENU BUTTON
READY INDICATOR
SET BUTTON
POWER ON–OFF BUTTON
INPUT BUTTON
WARNING TEMP. INDICATORLAMP INDICATORPOINT (VOLUME + / – ) BUTTONS 
LAMP REPLACE INDICATOR
Lights  green when the
projector is ready to be
turned on.  And it
flashes green in Power
Management mode.
(P36)
Becomes dim when the
projector is turned on.
And bright...

17
BEFORE OPERATION
HOW TO OPERATE THE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU
BAR).  The red frame is the POINTER.
Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.
Adjust the ITEM DATA by pressing the POINT RIGHT / LEFT
buttons.
Refer to the following pages for details of respective
adjustments.
Press POINT DOWN button and move POINTER (red frame
or red arrow) to the ITEM...

18
BEFORE OPERATION
MENU BAR
PC SYSTEM MENU
Used to select
computer system.
(Refer to P22, 23)
IMAGE ADJUST MENU
Used to adjust computer
image. [Contrast /
Brightness 
/ Color / Tint /
White balance (R/G/B) /
Sharpness / Gamma / Auto
grayscale / Auto fleshtone]
(Refer to P28)
SETTING MENU
Used to change
settings of projector
or reset Lamp
Replace Counter. 
(Refer to P35, 36)
SOUND MENU
Used to adjust
volume or mute
sound.
(Refer to P21)
IMAGE SELECT MENU
FOR PC SOURCEPress the MENU BUTTON while connected...

19
BASIC OPERATION
TURNING ON THE PROJECTOR
Connect the projectors AC Power Cord into an AC outlet.  LAMP
Indicator lights red, and READY Indicator lights green.
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON.  LAMP Indicator dims, and Cooling Fans
start to operate.  Preparation Display appears on a screen and
the count-down starts.  The signal from PC or Video source
appears after 30 seconds.  And then current image level is
displayed on screen for 4 seconds.
2
3
TURNING OFF...

20
Press the FREEZE button on the Remote Control Unit to freeze the
picture on-screen.  To cancel the FREEZE function, press the
FREEZE button again or press any other button.
PICTURE FREEZE FUNCTION
KEYSTONE ADJUSTMENT
1Press KEYSTONE /button on Remote Control Unit or
KEYSTONE button on Top Control or select Keystone on
SETTING menu.  (Refer to page 35.)  Keystone dialog box
appears.
2Correct keystone distortion by pressing KEYSTONE /button
or POINT UP/DOWN button(s).  Press KEYSTONE button or...