Canon projector LV8235 UST User Manual

31
Basic Operation
Press the BLANK button on the remote controller to black 
out the image. To restore to normal, press the BLANK 
button again or press any other button. When the projected 
image is captured and is set as User in the Logo selection 
(p.55), the screen changes each time you press the BLANK 
button as follows.
black out  the captured image  normal  • • • • •
Press the P-TIMER button on the remote controller. The 
Timer display “00 : 00” appears on the screen and starts to 
count time...

32
COMPUTER 1
3D
Choose COMPUTER 1(ANALOG PC) by pressing the 
COMPUTER 1 button on the remote controller. 
Before using these buttons, correct input source should be 
selected through Menu operation as described below.
1
Input Menu
2
3
Input Source Selection (COMPUTER 1: ANALOG PC)
Computer Input 
COMPUTER 1 button
Note:   When the Auto input function is set to On 1 or On 2 in 
the Auto setup function, the input signal will be searched 
automatically (p.53).
Remote Controller
Press the MENU button to...

33
3D
Choose COMPUTER2 (ANALOG PC) by press the 
COMPUTER 2 button on the remote controller. 
Note:   When the Auto input function is set to On 1 or On 2 in 
the Auto setup function, the input signal will be searched 
automatically (p.53).
COMPUTER 2 button
Remote Controller
1
2
Press the MENU button to display the On-Screen 
Menu. Press the Point  buttons, move the highlight 
to Input and then press the Point  or the OK button. 
Use the Point  buttons to select COMPUTER 2 and 
then press the OK...

34
Computer Input
PC System Menu
PC System Menu
Computer System Selection
This projector automatically tunes to various types of computers with it\
s Multi-scan system and Auto PC 
adjustment. If a computer is selected as a signal source, this projector\
 automatically detects the signal format 
and tunes to project a proper image without any additional settings. (S\
ignal formats provided in this projector are 
shown on pages 77-78.)
One of the following messages may appear when:
When the projector can...

35
Computer Input
Auto PC adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal position, 
Vertical position and Clamp position to conform to your computer.
PC adjust Menu
Auto PC adjustment
To store adjustment parameters
The adjusted parameters from the Auto PC adjustment can 
be stored in the projector. Once the parameters are stored, 
the setting can be done just by selecting a Mode (1–10) in 
the PC System Menu (See page 34). See also “Store” on 
page 37.
Note:
 •...

36
Computer Input
PC adjust Menu
Manual PC adjustment
Some computers employ special signal formats which may not be tuned by M\
ulti-scan system of this projector.  
Manual PC adjustment enables you to precisely adjust several parameters \
to match those signal formats. The 
projector has 10 independent memory areas to store those parameters manu\
ally adjusted. It allows you to recall 
the setting for a specific computer. 
1
2
Use the Point  buttons to adjust the value, eliminating a 
flicker from the...

37
Computer Input
To store the adjusted data, select Store and then press the 
Point  or the OK button. Move the highlight to one of the 
Modes 1 to 10 in which you want to store, and then press 
the OK button.
To clear the stored data, select Mode free and then press 
the Point  or the OK button. Move the highlight to the 
Mode that you want to clear and then press the OK button.
Note:
 • When input computer signal to the projector, PC adjust 
will become available.
To  reset  the  adjusted  data,...

38
Computer Input 
3D
Image Select Menu
IMAGE button
Presentation
High contrast
User 1
User 2
User 3
Image Mode Selection 
User 4
Cinema
Standard
Remote Controller
IMAGE button
Select  the  desired  image  mode  among Presentation, 
Standard, High  contrast, Cinema, User  1,User  2,User  3, 
and User  4  by  pressing  the  IMAGE  button  on  the  remote 
controller.
Picture mode with improved halftone for graphics.
Direct Operation
For viewing pictures in a bright room.
Normal picture mode preset on the...

39
Computer Input
Image adjust Menu
Image Adjustment
Press the MENU button to display the On-Screen 
Menu. Use the Point  buttons to select Image 
adjust and then press the Point  or the OK  button.
1
2Use the Point  buttons select the desired item and 
then press the OK button to display the adjustment 
dialog box. Use the Point  buttons to adjust the 
setting value.
Note:
•  When White balance Red, Green or Blue is 
adjusted, Color temp. will change to User.
Press the Point  button to decrease...

40
Computer Input
Provide the image in its original size. When the original 
image size is larger than the panel resolution (DLP chip 
1280 x 800 dots), the projector automatically switches to 
the panning mode. Use the Point  buttons to pan the 
image. When adjusted, the arrows turn red. When reached 
to the correction limit, the arrows disappear.
Provide the last stored aspect screen image. 
True
Custom
This projector has the picture screen resize function, which 
enables you to customize the image...