Canon projector LV7585 User Manual

1

RGB Scart21-pin Output
Connecting to Video Equipment (Video, S-Video)
S-video cable
S-video OutputComposite Video
Y - Pb/Cb - Pr/Cr
BNC cable
Unplug	the	power	cords	
of	both	the	projector	
and	external	equipment	
from	the	AC	outlet	before	
connecting	cables.
Cables used for connection (] = Cables not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) ]
• BNC Cable ]
• S-VIDEO Cable ]
• Scart-VGA Cable    ]
Component Video OutputComposite Video
Component Video Output(Y, Pb/Cb,...



This projector uses nominal input voltages of 100–120 V or 200–
240 V AC and it automatically selects the correct input voltage. It 
is designed to work with single-phase power systems having a 
grounded neutral conductor. To reduce the risk of electrical shock, 
do not plug into any other type of power system.
If you are not sure of the type of power being supplied, consult 
your authorized dealer or service station.
Connect the projector with all peripheral equipment before turning 
on the...



Turning On the Projector
Connect the projector’s AC power cord into an AC 
outlet. The LAMP indicator lights red and the POWER 
indicator lights green.
Press the POWER button on the side control or the 
ON button on the remote control unit. The LAMP 
indicator dims and the cooling fans start to operate. 
The preparation display appears on the screen and the 
countdown starts. 
2
3
1
The preparation display will disappear after 30 seconds.
4After the countdown, the input source that was...

4

Press the POWER button on the side control or the 
STAND-BY button on the remote control unit, and 
“Power off?” appears on the screen.
Press the POWER button on the side control or the 
STAND-BY button on the remote control unit again to 
turn off the projector. The LAMP indicator lights bright 
and the POWER indicator turns off. After the projector 
is turned off, the cooling fans operate for 90 seconds. 
You cannot turn on the projector during this cooling 
down period.
1
2
TO MAINTAIN THE...

5

Side Control
OK button
How to Operate the On-Screen Menu
MENU button
OK button
POINT buttons
On-Screen Menu
The projector can be adjusted or set via the On-Screen 
Menu. For each adjustment and setting procedure, refer to 
the respective sections in this manual.
Use the Point 7 8 buttons to select a Menu icon. Use 
the Point ed buttons to select an item in the selected 
menu.
Press the OK button to show the item data. Use the 
Point 7 8 buttons to adjust the values.
To close the On-Screen Menu,...

6

Menu Bar
For Computer Source
For Video Source
Same function as menu 
for Computer Source.
Same function as menu 
for Computer Source.
Guide Window
Show the selected 
Menu of the On-
Screen Menu.
PC System Menu
Used to select 
computer system
(p. 34).
Image Select Menu
Used to select 
an image level 
among Standard, 
High contrast, and 
Custom 1–10 (p.38).
Screen Menu
Used to adjust the size of 
the image. [Normal/True/
Wide/Full screen/Custom/
Keystone/Ceiling/Rear/Reset/
Digital zoom +/–]...

7

Operating with Projector Control
The following lens operation can be made with the Lens 
button on the side control. 
Press the LENS button to enter each lens operation mode. 
The selected adjustment display appears on the screen.
Display “Lens shift” on the screen. Use the Point ed7 8 
buttons to position the screen to the desired point without 
having picture distortion. 
The screen can be moved up or down to 50 percent, or 
sideways up to 10 percent from the central axis of the 
lens shift....

8

Operating with Remote Control Unit
Using the remote control unit for some frequently used operations is advisable. Just pressing one of the 
buttons enables you to make the desired operation quickly without calling up the On-Screen Menu.
Press the FREEZE button on the remote control unit to 
freeze the picture on the screen. To cancel the FREEZE 
function, press the FREEZE button again or press any other 
button.
FREEZE button
Press the AUTO PC button on the remote control unit to 
operate the...

9

Press the BLANK button on the remote control unit to black 
out the image. To restore to normal, press the BLANK button 
again or press any other button.
BLANK button
FILTER button
Press and hold the FILTER button for more than 5 seconds 
to operate electrically operated filter to replace the filter.
KEySTONE button
Reduce  the  upper  width  with Point e button. Re d u c e   t h e   l owe r   w i d t h with Point d button.  Reduce  the  left  part  with Point 7 button.  Reduce  the  right  part...

0

Pointer Function
Pointer
✔Note:
	 •	 You	can	choose	the	pattern	of	Pointer	(Arrow/Cross/Dot)	in	the	Setting	Menu	(p.	52)
You can move the Pointer of the projector with the remote control unit to emphasize a part of the projected 
image.  
Press the POINTER button to activate the Pointer 
function.1
2
3
MOUSE POINTER button
POINTER button
To cancel the Pointer function, press the POINTER 
button again or press any other button. 
Use the MOUSE POINTER button to move the Pointer. 
Wireless Mouse...