Canon projector LV7392A User Manual
Here you can view all the pages of manual Canon projector LV7392A User Manual. The Canon manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 11
11 Part Names and Functions Rear Terminal ②③① ⑥ ⑤ ⑧ ④ ④ VIDEO IN Connect the composite video output signal to this jack (p.18). ② COMPUTER IN/S-VIDEO IN / COMPONENT IN Connect output signal from a computer, component video output, RGB scart 21-pin video output or S-VIDEO output to this terminal (pp.17-19). ⑥ AUDIO OUT (VARIABLE) Connect an external audio amplifier to this jack (pp.17-19). This terminal outputs sound from AUDIO IN terminal ⑦ or ⑧, or HDMI terminal ③ (digital audio). Never plug...
Page 12
12 Part Names and Functions Top Control ⑦ LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.68, 75). ⑧ WARNING indicator – Lights red when the projector detects an abnormal condition. – Blinks red when the internal temperature of the projector exceeds the operating range (pp.65, 75).④ POWER buttonTurn the projector on or off (pp.21-23). ⑤ POWER indicator – Lights red when the projector is in stand-by mode. – Lights green during operations. – Blinks green...
Page 13
Part Names and Functions 13 Part Names and Functions LV-RC0 6 Note: To ensure safe operation, please observe the following precautions:– Do not bend, drop or expose the remote control unit to moisture or heat.– For cleaning, use a soft dry cloth. Do not apply benzene, thinner, spray, or any chemical material. Remote Control Unit ⑦ ⑭⑩ ⑳④ ⑱ ② ⑧ ⑨ ⑬ ⑯ ⑤ ⑥ ⑪ ⑫ ⑲ ⑮ ③ ② AUTO SET button Execute the setting of Auto setup (includes Auto input, Auto PC and Auto Keystone functions) in the setting menu. (pp.26,...
Page 14
14 Part Names and Functions To ensure safe operation, please observe the following precautions : ● Use two (2) AAA type batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control unit to moisture or heat. ● Do not drop the remote control unit. ● If the battery has leaked on the remote control unit, carefully wipe the case clean and install new batteries. ● Risk of an explosion if battery is...
Page 15
Part Names and Functions 15 Positioning the Projector For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. Installation Note: • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image. • All measurements are approximate and may vary from the actual sizes. A B 100 150 200 250167 125 83 300(wide) 40300(tele ) Max. ZoomMin. Zoom (Inch Diagonal )...
Page 16
16 Installation Adjust the Height and the Incline angle of the projected image Adjustable FootFoot Lock Latch Projection angle can be adjusted up to 10.0 degrees with the adjustable foot. Lift the front of the projector and push the foot lock latch on the projector. Release the foot lock latch to lock the adjustable foot and rotate the adjustable foot to adjust the position and tilt. To retract the adjustable foot, lift the front of the projector and push and undo the...
Page 17
Installation 17 Installation Connecting to a Computer Note: Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. Note:•When the MIC function is set to Off in the Sound menu, the MIC function is disabled.•When MIC is set to On in Sound Menu, AUDIO IN (PC/MIC) and AUDIO IN(L/R) terminals can be connected at the same time. At this time, AUDIO IN (PC/MIC) termianl as MIC input, AUDIO IN(L/R) terminal as COMPUTER...
Page 18
18 Installation Connecting to VIDEO Equipment External Audio Equipment Audio cable (stereo) S-VIDEO cable Audio Output S-VIDEO Output Audio Input AUDIO IN(PC or MIC) S-VIDEO-VGA cable VIDEO cable COMPUTER IN/ S-VIDEO IN/COMPONENT IN VIDEO IN Audio cable (stereo) AUDIO OUT (stereo) AUDIO IN Audio cable (stereo) Cables used for connection • VIDEO Cable • S-VIDEO Cable • S-VIDEO-VGA Cable • Audio Cables• HDMI Cable(Cables are not supplied with the projector. ) Note:• When the MIC function...
Page 19
Installation 19 Installation Connecting to COMPONENT VIDEO and SCART Equipment External Audio Equipment PC AUDIO IN Audio cable (stereo) Audio Input COMPONENT VIDEO Output(Y, Pb/Cb, Pr/Cr)Audio OutputRGB Scart 21-pin Output Scart-VGA cable COMPONENT- VGA cable AUDIO OUT (stereo) COMPONENT cable COMPUTER IN/ S-VIDEO IN / COMPONENT IN Cables used for connection • Audio Cables • Scart-VGA Cable • COMPONENT Cable • COMPONENT-VGA Cable (Cables are not supplied with this projector.) Audio cable...
Page 20
20 Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100-240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.If you are not sure of the type of power being supplied, consult your authorized dealer or service center.C o n n e c t t h e p...