Canon projector LV7320 User Manual

S-VIDEO
R-AUDIO-L(MONO)VIDEOAUDIO
IN
OUT
CONTROL PORT
COMPUTER IN
MONITOR OUT
11
CONNECTING THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
Video Source (example)
Video Cassette Recorder Video Disc Player
Video Audio Cable ]S-VIDEO Cable ]
Audio Amplifier Audio Speaker
(stereo) External Audio Equipment
Audio Cable (Stereo) ]
Terminals 
of the Projector
Use either the VIDEO jack
or the S-VIDEO jack.
When the both jacks are
connected, the S-VIDEO
jack has priority over the
VIDEO jack. Video / Audio Output...

12
CONNECTING THE PROJECTOR
ON
12
34
56DIP
CONNECTING TO THE COMPUTER
To connect to the computer, refer to the figure below.
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)
VGA Cable 
Monitor Output  Desktop type
Laptop type
Monitor
Audio Speaker
(stereo)
Audio Amplifier
Control Cable for Serial Port ]
Control Cable for PS/2 Port Audio Cable (stereo) 
]
Monitor Cable ]
Terminal Terminal Serial port PS/2 port Audio Output Audio InputTo each terminal of your computer
To the...

13
CONNECTING THE PROJECTOR
S-VIDEO
R-AUDIO-L(MONO)VIDEOAUDIO
IN
OUT
CONTROL PORT
COMPUTER IN
MONITOR OUT
ON
1DIPON
OFF
23456
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF ON ON
ON ON
ON ONOFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
1234 56
OFF OFF ON ON ON ON 21 MODE (1152 x 870)
CONTROL
PORTAUDIO
OUT AUDIO
IN MONITOR
OUT COMPUTER
IN
Use one of these Control
Cables corresponding
with the terminal of your
computer.Set the switches as shown
in the table below depend-
ing on the...

14
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
VOLUME
POWER
FOCUS
ZOOMVIDEO
COMPUTER
D.ZOOM
MENUMUTE
LASER
KEY STONENO SHOWFREEZE
AUTO IMAGENORMAL
ON
ALL OFF
ALL-OFF SWITCH
When using the Remote Control
Unit, turn this switch to “ON” and
turn it “ALL OFF” when it is not
used.
This remote control emits a laser beam as the Laser Pointer from the Laser Light Window.  When the LASER button is
pressed, the laser light goes on.  And when the button is pressed more than 1 minute or the button is released,...

15
BEFORE OPERATION
VOLUME
POWER
FOCUS
ZOOMVIDEO
COMPUTER
D.ZOOM
MENUMUTE
LASER
KEY STONENO SHOWFREEZE
AUTO IMAGENORMAL
To insure safe operation, please observe the following precautions :
lUse (2) AA type alkaline batteries.
lReplace two batteries at the same time.
lDo not use a new battery with a used battery.
lAvoid contact with water or liquid.
lDo not expose the Remote Control Unit to moisture, or heat.
lDo not drop the remote control unit.
lIf batteries have leaked on the remote control, carefully...

POWER
NORMALMENU MODEAUTO IMAGE
FOCUSZOOM
VOLUME
KEYSTONE
LAMP
REPLACEWARNING
TEMP.READYLAMP
WIDE
TELESELECT
BRIGHT
16
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
Used to open or close the
MENU operation. 
(P17, 18)
MENU BUTTON
AUTO IMAGE BUTTON
READY INDICATOR
POWER ON–OFF BUTTON
WARNING TEMP. INDICATORLAMP INDICATORLAMP REPLACE INDICATOR
Used to operate AUTO
IMAGE function.  (P27)
This indicator is lit in green
when the projector is ready
to be turned on.This indicator is dim when
the projector is...

17
SELECT
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU
Display ON-SCREEN MENU
Press MENU button to display the ON-SCREEN MENU
(MENU BAR).  The red frame is the POINTER.
Select the ITEM by pressing SELECT button.  The
dialog box of the ITEM appears.
Move the POINTER (red frame) to the ITEM ICON that
you want to select by pressing POINT RIGHT/ LEFT
buttons.
Move the POINTER to the ITEM that you want to adjust
and adjust the ITEM by pressing SELECT button.
Refer to the following...

18
BEFORE OPERATION
MENU BAR
IMAGE MENU
Used to adjust  the
computer image. [Fine
sync. / Total dots /
White Balance /
Contrast / Brightness]
(Refer to P26)
PC ADJUST MENU
Used to adjust the
parameters to
match with the input
signal format.
(Refer to P24, 25)
SETTING MENU
Used to set the Display
Menu and to reset
Lamp Replacement
Monitor Timer.
(Refer to P31)MODE MENU
Used to select
the  Computer
input mode.
(Refer to P22)
SCREEN MENU
Used to adjust the
size of the image
or to correct the
Keystone...

19
BASIC OPERATIONS
TURNING ON THE PROJECTOR
Connect the projectors AC power cord into a wall outlet.  The
LAMP indicator lights RED, and the READY indicator lights
GREEN.
Press the power ON-OFF button on the Remote Control Unit or
on  the Top Control to ON.  The LAMP POWER indicator dims,
and the Cooling Fans start to operate.  The Preparation Display
appears on the screen and the count-down starts.  The signal
from the source appears after 30 seconds.
2
3
TURNING OFF THE PROJECTOR
Press the power...

20
BASIC OPERATION
ADJUSTING THE IMAGE
The message disappears after 4 seconds.
The message disappears after 4 seconds.
ZOOM ADJUSTMENT
1Press the ZOOM WIDE/TELE button(s) on the Top Control or
the ZOOM s/tbutton on the Remote Control Unit to turn into
the ZOOM mode.
2Press the ZOOM WIDE button or the ZOOM sbutton to make
the image larger, and press the ZOOM TELE button or the
ZOOM tbutton to make the image smaller.
FOCUS ADJUSTMENT
1Press the FOCUS s/tbutton(s) on the Top Control or on the
Remote Control...