Canon projector LV7250 User Manual

12
2. Installation and Connections

 Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 25 measured diagonally when the projector is roughly 1.1 m (3.7’) from the wall or screen. The largest
the image can be is 300 when the projector is about 8.8 m (29.1’) from the wall or screen. Use the drawing below as
a guide.
NOTE:
This projector can be hung from the ceiling...

13
2. Installation and Connections
WARNING
•Installing your projector on the ceiling must be done
by a qualified technician. Contact your dealer for more
information.
•Do not attempt to install the projector yourself.
•Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
•Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 41˚F (5˚C) and 104˚F (40˚C). (Quiet...

14
2. Installation and Connections
 Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered
up.
*If the screen goes blank while using your remote control, it may be the result of the computers screen-saver or power
management software.
AUDIO...

15
2. Installation and Connections
AUDIO INANALOG IN-1
AUDIO OUTS-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORTANALOG IN-2
ANALOG IN-1
Before connections: An exclusive Scart adapter (LV-CA35) and a commercially available Scart cable are required for
this connection.
NOTE: Audio signal is not available for this connection.
From the menu, select [Setup] → [Input signal select] → [Computer-1 ([Computer] on LV-X6 )] → [SCART].
Scart is a standard European audio-visual connector for TVs, VCRs and DVD players. It is...

16
2. Installation and Connections
Connecting an External Monitor
AUDIO INANALOG IN-1
AUDIO OUTS-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORTANALOG IN-2
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
image youre projecting.
NOTE: Daisy chain connection is not possible.
NOTE:
•The signal from the ANALOG-2 IN connector cannot be output from the MONITOR OUT connector on LV-7250.
•The LV-X6 does not have the AUDIO OUT connector.
•Use an audio...

17
AUDIO INLR
AUDIO OUT
LR
Component
YCbCr
AUDIO INANALOG IN-1
AUDIO OUTS-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORTANALOG IN-2
ANALOG IN-1AUDIO IN 
ANALOG IN
ANALOG IN
2. Installation and Connections
A component signal will be automatically displayed. If not, from the menu, select [Setup] → [Input signal select] →
[Computer-1 ([Computer] on LV-X6 )] → [COMPONENT].
NOTE: Refer to your DVD players owners manual for more information about your DVD players video output requirements.
Connecting Your DVD Player...

18
2. Installation and Connections
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
AUDIO INANALOG IN-1
AUDIO OUTS-VIDEOIN
VIDEO
INL
AUDIO INRSERVICE PORTANALOG IN-2
VIDEO INAUDIO IN
S-VIDEO IN
Connecting Your VCR or Laser Disc Player
S-Video cable (not supplied)
Video cable (not supplied)
VCR/ Laser disc player
Audio equipment
Audio cable (not supplied)
NOTE: The AUDIO IN L/MONO and R jacks (RCA) are shared between the Video and S-Video inputs.
NOTE: Refer to your VCR or laser disc player owners manual for...

19
2. Installation and Connections
S-VIDEO
INVIDEO
INSER
VIC
E PO
RTA
UDIO
 INAUDIO OUT
R LAUDIO INANALOG IN-1ANALOG IN-2
MENU
BACKKEYSTONE
W
A
R
N
IN
GPOWERAUTO PCINPUT
VOL-VOL+
LAMP
Connecting the Supplied Power Cord
Connect the supplied power cord to the projector.
First connect the supplied power cords two-pin plug to the AC IN of the projector, and then connect the other plug of
the supplied power cord in the wall outlet.
Make sure that the prongs are fully inserted into
both the AC IN and the wall...

20
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.

 Turning on the Projector
NOTE:
•The projector has two power switches: a main power switch and a POWER button.
•When plugging in or unplugging the supplied power cord, make sure that the main power switch is pushed to the off (
)
position. Failure to do so may cause damage to the projector.
WARNING
LAMP
POWER1. To turn on the main power to the projector, press the...

21
VOL-VOL+
MENU
BACK
KEYSTONE
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 8 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT  or  button to select one of the
8 languages for the menu.POWER
BACK INPUT IMAGE
ASPECT
INFO.
MENUNO SHOW
AUTO PC
2. Press the OK button to execute the selection.
After this...