Canon projector LV7250 User Manual

2
1. Introduction
 Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
Congratulations on Your Purchase of The Projector
The LV-7250/LV-X6 is one of the very best projectors available today. The projector enables you to project precise
images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook),
VCR, DVD player, document camera, or a laser disc player.
You can use the projector on a...

3
About this users manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to
review the users manual. This may save you time later on. At the beginning of each section of the manual youll find an
overview. If the section doesnt apply, you can skip it.
•IBM is a trademark or registered trademark of International Business Machines Corporation.
•Mac and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other...

4
1. Introduction
 Part Names of the Projector
M
EN
U
BA
C
KKEYSTONE
WARNINGPOWERAUTO PCI
N
P
U
TLAMP
-+VOLVOL
S-VIDEO
INV
I
D
E
O
INSERVICE PORTAUDIO INA
U
D
IO
 O
U
T
R LA
U
D
I
O
 
INAN
A
LO
G
 IN
-1A
N
A
LO
G
 IN
-2
MENU
BACKKEYSTONE
WARNINGPOWERAUTO PCINPUTVOL-VOL+
LA
M
P
Zoom Lever
(See page 24)Controls
(See page 6)
Lens
Lens Cap
Be sure to remove the lens cap during
projection. The cap can deform or fire
can occur.
Built-in Security Slot (  )*
Focus Ring
(See page 24)
Adjustable Tilt Foot Lock...

5
1. Introduction
Bottom
Adjustable Tilt  Foot
(See page 23)
Adjustable Tilt Foot Lock Button
(See page 23)Lamp Cover
(See page 53)
Rear Foot (Left / Right)
HINT: The Canon logo is on the panel of the projector cabinet . When projecting an image with the projector hung from the
ceiling, turn the Canon logo upside down.
To turn the logo upside down, follow the steps below.
1. Push one end of the logo gently.
The other end will pop up slightly.
•The right drawing shows the part “C” is pressed gently.
•The...

6
1. Introduction
Top Features
MENU
BACK
KEYSTONE
WARNING
POWER
AUTO PC
INPUT
VOL-VOL+
LAMP
3
4
158
9
2
106
7
1. POWER Button (  )
Use this button to turn the power on and off when the
main power is supplied and the projector is in standby
mode.
To turn on the projector, press and hold this button for
about 1 second. To turn off the projector, press this
button twice.
2. POWER Indicator
When this indicator is green, the projector is on; when
this indicator is orange, it is in standby mode. See the
Power...

7
1. Introduction
AUDIO IN
AUDIO OUT
S-VIDEOIN
VIDEO
INL
AUDIO IN
RSERVICE PORT
ANALOG IN-1
ANALOG IN-2
973148
256
Terminal Panel Features
1.ANALOG IN-1 and -2 (ANALOG IN on LV-X6) / Com-
ponent Input Connector (Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equip-
ment such as IBM compatible or Macintosh comput-
ers. Use the supplied RGB cable to connect to your
computer. This also serves as a component input con-
nector that allows you to connect a component video
output of component...

8
1. Introduction
 Part Names of the Remote Control
1. Infrared Transmitter
Direct the remote control toward the remote sensor
on the projector cabinet.
2. POWER Button
When the main power is on, you can use this button
to turn your projector on.
NOTE: To turn on the projector, press and hold the POWER
button for about 1 second.
You can use this button to turn your projector off.
NOTE: To turn off the projector, press this button twice.
3. INFO. Button
Provides the information on the current signal and...

9
BACK
R-
CLICKL-
CLICK
VOL
FREEZE
D.ZOOMPAGE MENU
POWER
RD-428E
INPUT IMAGE
ASPECT
INFO.
NO SHOW
AUTO PC
1
2
46
78
3
5
13 11
1514 1217
18 16
9
10
1. Introduction
11. OK Button
Use this button to enter your menu selection. It works
the same way as the OK button on the cabinet. See
page 6.
12. BACK Button
It works the same way as the BACK button on the
cabinet. See page 6.
13. L-CLICK Button
(Not available on LV-X6)
This button works as the mouse left button when the
supplied remote mouse receiver is...

10
1. Introduction
Remote Control Precautions
•Handle the remote control carefully.
•If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
•Do not heat, take apart, or throw batteries into fire.
•Ensure that you have the batteries polarity (+/-) aligned correctly.
•If you will not be using the remote control for a long time, remove the batteries.
•Do not place the batteries upside down.
•Do not use new and old batteries together, or use different types of batteries...

11
This section describes how to set up your projector and how to connect video and audio sources.
2. Installation and Connections
Your projector is simple to set up and use. But before you get started, you must first:
	 Set up a screen and the projector. See page 12.

 Connect your computer or video equipment to the projector. See pages 14 to 18.
 Connect the supplied power cord. See page 19.
NOTE: Ensure that the power cord and any other cables are disconnected before moving the projector. When moving...