Canon projector LV7245 User Manual

							53
7. Appendix
Common Problems & Solutions (See also POWER/WARNING/LAMP REPLACE Indicator on page 52.)
Does not turn on
Will turn off
No picture
Picture suddenly
becomes dark
Color tone or Color
balance is unusual
Image isn’t square to
the screen
Picture is blurred
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or
blinking
Cross color in RGB
mode
Whenever the projector
is turned on, a message
prompting you to clean
the filter will be dis-
played•Check that the power cord is plugged in and that the power button on the projector cabinet or the remote
control is on. See pages 19 and 20.
•Ensure that the lamp cover is installed correctly. See page 50.
•Check to see if the projector has overheated or the lamp usage exceeds 2100* hours (up to 3100* hours :
Quiet mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is
particularly warm, move the projector to a cooler location.
*LV-X5: 3100 hours (up to 4100 hours in Quiet mode).
•The lamp may fail to light. Wait a full minute and then turn on the power again.
•The lamp has reached the end of its usable life. Replace the lamp.
•Ensure that the Power Management is off. See page 44.
•Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Computer,
Video or S-Video). See page 22. If there is still no picture, press the button again.
•Ensure your cables are connected properly.
•Use menus to adjust the brightness and contrast. See page 37.
•Remove the lens cap.
•
Reset the settings or adjustments to factory preset levels using the “Factory default” in the Menu. See page 46.•Enter your registered Password if the Password function is enabled. See page 41.
•When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
*If the screen goes blank while using your remote control, it may be the result of the computers screen-
saver or power management software.
•See also the next page.
•When one of the following happens, the Lamp mode automatically changes from Normal to Quiet.
*When there are no signals (blue or black screen) → To return to the Normal mode, select another available
source.
*When the image is muted using the NO SHOW button on the remote control → Press the NO SHOW button
again to return to the Normal mode.
*When the room where you re presenting is particularly warm → Move the projector to a cooler location.
•Check if an appropriate color is selected in Screen color. If so, select an appropriate option. See page 36.
•Adjust Color balance in Image adjustment. See page 37.
•Reposition the projector to improve its angle to the screen. See page 23.
•Use the Keystone correction function to correct the trapezoid distortion. See page 25.
•Adjust the focus. See page 24.
•Reposition the projector to improve its angle to the screen. See page 23.
•Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
11.
•Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
•Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Video, S-
Video or Computer). See page 22.
•Adjust the computer image manually with the Horizontal/Vertical position in the “Advanced settings → Page
2”. See page 44.
•Install new batteries.See page 10.
•Make sure there are no obstacles between you and the projector.
•Stand within 7 m (22 feet) of the projector. See page 10.
•See the POWER/WARNING/LAMP REPLACE Indicator on page 52.
•Press the AUTO PC button on the projector cabinet or the remote control. See page 27.
•When “Off” is selected in Auto PC adjustment, adjust the computer image manually with Clock/Tracking in
“Advanced settings → Page 2” in the menu. See pages 44 and 45.
•Clean or replace the filter and then reset the Filter counter. See page 46.
Problem Check These  Items
For more information contact your dealer. 
						

							54
7. Appendix
If there is no picture, or the picture is not displayed correctly.
•Power on process for the projector and the PC.
Be sure to connect the RGB cable between the projector and the computer before turning on the computer.
There are some notebook PCs, which do not output signal unless there is a projector or monitor connected first.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information.  If it reads
“0kHz”, this means there is no signal being output from the computer. See page 45 or go to next step.
•Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projec-
tor.  When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come
on or off.  For more details, refer to your computer’s owner’s manual.
•Non-standard signal output from the computer
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.
Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the
previous step. Refer to your computer’s documentation for detailed information.
•Image displayed is incorrect when using a Macintosh
When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projec-
tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP
switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP
switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a
displayable mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.
•Mirroring on a PowerBook
*When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirror-
ing” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
•Folders or icons are hidden on the Macintosh screen
Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple
menu and arrange icons. 
						

							55
7. Appendix
 Specifications
This section provides technical information about the projectors performance.
Model Number LV-7245/LV-7240/LV-X5
Optical
LCD Panel 0.7 p-Si TFT active-matrix with Micro Lens Array
Resolution 1024 
 768 pixels* native, up to UXGA with scaling technology
Lens Manual zoom and manual focus
F1.7 - 2.0   f=21.6 - 25.9 mm
LampLV-7245 : 190W DC lamp (150W Quiet mode)
LV-7240: 180W DC lamp (150W  Quiet mode)
LV-X5: 130W DC lamp (110W  Quiet mode)
BrightnessLV-7245: 2500 lm
LV-7240: 2100 lm
LV-X5: 1500 lm
Uniformity 85%
Image Size (Diagonal) 21 to 300
Projection Distance 0.7 m to 10.9 m / 2.4 to 35.8
Projection Angle Tele: 9.5° - 9.9°/ Wide: 11.5° - 12.0°
Keystone Correction +/- 30° Vertical (auto)
Electrical
Inputs 2 RGB/Component (D-Sub 15 Pin),
1 S-Video (DIN 4 Pin), 1 Video (RCA), 2 (L/R) RCA Audio,
1 Stereo Mini Audio, 1 Service Port (DIN 8 Pin)
Outputs 1 RGB (D-Sub 15 Pin), 1 Stereo Mini Audio
Video Compatibility NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM,
1080p, 1080i, 720p, 480p, 480i / 60Hz
1080i, 576p, 576i / 50Hz
Scan Rate Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 50 Hz to 120 Hz
Video Bandwidth RGB: 80 MHz (-3dB)
Color Reproduction 16.7 million colors simultaneously, Full color
Horizontal Resolution NTSC / NTSC4.43/PAL/PAL-M/PAL-N/PAL60/YCbCr: 540 TV lines
SECAM: 300 TV lines
RGB: 1024 dots (H)
768 dots (V)
External Control RS232, IR
Sync Compatibility Separate Sync / Composite Sync / Sync on G
Built-in Speaker 1W (monaural)
Power Requirement 100 - 240V AC, 50 / 60 Hz
Input CurrentLV-7245/LV-7240: 2.7 - 1.4A
LV-X5: 2.1 - 1.2A
Power ConsumptionLV-7245/LV-7240: 8W in Standby mode /
250W in Lamp Normal mode / 200W in Lamp Quiet mode
LV-X5: 8W in Standby mode /
190W in Lamp Normal mode / 155W in Lamp Quiet mode
* Effective pixels are more than 99.99%. 
						

							56
7. Appendix
Mechanical
Installation Orientation Front / Rear / Ceiling mounted / Rear, Ceiling mounted
Dimensions 11.6 (W)
3.7 (H)
10.2 (D)
294mm (W)
93mm (H)
260mm (D)
(not including protrusions)
Weight approx. 7 lbs / 3 kg
Fan NoiseLV-7245/LV-7240: 35 dB (Normal mode), 30dB (Quiet mode)
LV-X5: 33 dB (Normal mode), 28dB (Quiet mode)
Environmental Considerations Operational Temperatures : 41° to 95°F (5° to 35°C),
20% to 80% humidity (non-condensing)
Storage Temperatures : 14° to 122°F (-10° to 50°C),
20% to 80% humidity (non-condensing)
Regulations
For United States:
UL Approved (UL 60950)
Meets FCC Class B requirements
For Canada:
UL Approved (CSA 60950)
Meets DOC Canada Class B requirements
For Australia/New Zealand:
Meets AS/NZS CISPR.22 Class B
For Europe:
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950)
The specifications are subject to change without notice. 
						

							57
7. Appendix
 Cabinet Dimensions
112.5 (4.4)
260 (10.2)
20.3 (0.8)
64.6 (2.5)
294 (11.6)
71.5 (2.8)
AC IN
VIDEO INL   AUDIO IN   R
S-VIDEO IN
ANALOG IN-1
ANALOG IN-2
AUDIO OUTL   AUDIO IN   R
MONO MONO
SERVICE PORTAUDIO IN
POWERVIDEO S-VIDEOCOMPUTER-1 COMPUTER-2WARNINGLAMP REPLACE
AUTO PC
VOL-VOL+
ZOOM
FOCUS
Lens center
Lens center
Unit: mm (inch) 
						

							58
Mini D-Sub 15 Pin Connector
 Pin Assignments of D-Sub ANALOG Input Connector
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
51423
10
11 12 13 14 156 978
7. Appendix
* Only ANALOG-1 input connector supported.
Pin No. RGB Signal (Analog) YCbCr Signal
1Red Cr
2Green or Sync on Green Y
3Blue Cb
4Ground
5Ground
6Red Ground Cr Ground
7Green Ground Y Ground
8Blue Ground Cb Ground
9No Connection
10 Sync Signal Ground
11 Scart Sync
12 Bi-directional DATA (SDA)*
13Horizontal Sync or Composite Sync
14 Vertical Sync
15 Data Clock* 
						

							59
7. Appendix
 Compatible Input Signal List
Signal Resolution Frequency H. Refresh Rate
( Dots ) ( kHz ) ( Hz )
NTSC – 15.73 60
PAL–15.63 50
PAL60 – 15.73 60
SECAM – 15.63 50
VESA 640
480 31.47 59.94
IBM 640
480 31.47 60
MAC 640
480 34.97 66.67
MAC 640
480 35 66.67
VESA 640
480 37.86 72.81
VESA 640
480 37.5 75
IBM 640
480 39.38 75
VESA 640
480 43.27 85.01
IBM 720
350 31.47 70.09
IBM 720
350 39.44 87.85
IBM 720
400 39.44 87.85
VESA 800
600 35.16 56.25
VESA 800
600 37.88 60.32
VESA 800
600 48.08 72.19
VESA 800
600 46.88 75
VESA 800
600 53.67 85.06
MAC 832
624 49.73 74.55
VESA 1024
768 35.5 43 Interlaced
VESA 1024
768 48.36 60
VESA 1024
768 56.47 70.07
MAC 1024
768 60.24 74.93
VESA 1024
768 60.02 75.03
VESA 1024
768 68.68 85
#VESA 1152
864 67.5 75
#MAC1152
870 68.68 75.06
#SGI 1152
900 71.74 76.05
#VESA 1280
960 60 60
#VESA 1280
1024 63.98 60.02
#MAC1280
1024 69.89 65.18
#VESA 1280
1024 79.98 75.03
#VESA 1280
1024 91.15 85.02
#SXGA+ 1400
1050 65.32 59.98
#HDTV (1080p)1920
1080 67.5 60 Progressive
#SDTV(576i)(625i)–15.6 50
#SDTV(576p)(625p)–31.5 50
#HDTV (1080i)(1125i)1920
1080 33.75 60 Interlace
#HDTV (1080i)(1125i)1920
1080 28.13 50 Interlace
#HDTV (720p)(750p)1280
720 45 60 Progressive
#SDTV (480p)(525p)–31.47 59.94 Progressive
#VESA 1600
1200 75.0 60
#VESA 1600
1200 81.25 65
#VESA 1600
1200 87.5 70
#VESA 1600
1200 93.75 75
DVD YCbCr – 15.73 59.94  Interlaced
DVD YCbCr – 15.63 50  Interlaced
# : Images in above flagged with # are compressed with scaling technology.
NOTE: Some composite sync signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh
rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
UXGA (1600 x 1200) is supported for separate sync signal only. 
						

							60
7. Appendix
 PC Control Codes and Cable Connection
PC Control Codes
Function Code Data
POWER ON 02H 00H 00H 00H 00H 02H
POWER OFF 02H 01H 00H 00H 00H 03H
INPUT SELECT COMPUTER-1 02H 03H 00H 00H 02H 01H 01H 09H
INPUT SELECT COMPUTER-2 02H 03H 00H 00H 02H 01H 02H 0AH
INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH
INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H
NO SHOW ON 02H 10H 00H 00H 00H 12H
NO SHOW OFF 02H 11H 00H 00H 00H 13H
SOUND MUTE ON 02H 12H 00H 00H 00H 14H
SOUND MUTE OFF 02H 13H 00H 00H 00H 15H
Cable Connection
Communication Protocol
Baud rate ........................................ 19200 bps
Data length ..................................... 8 bits
Parity .............................................. No parity
Stop bit .......................................... One bit
X on/off .......................................... None
Communications procedure ........... Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.
1 2 54 36
7 8
To RxD of PC
PC Control Connector (DIN-8P)
To TxD of PC
To GND of PC
NOTE: Pins 2, 3, 5, 6 and 8 are used inside the projector. 
						

							61
7. Appendix
 Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed, you may
also refer to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem
more efficiently.
* Print the following pages.
No image is displayed from your PC or video equipment to the
projector.
Still no image even though you connect the projector to the PC
first, then start the PC.
Enabling your notebook PC’s signal output to the projector.
•A combination of function keys will enable/disable the ex-
ternal display. Usually, the combination of the “Fn” key along
with one of the 12 function keys turns the external display
on or off.
No image (blue background, logo, no display).
Still no image even though you press the AUTO PC button.
Still no image even though you carry out “Factory default” in
the projector’s menu.
Signal cables plug is fully inserted into the input connector
A message appears on the screen.
( _____________________________________________ )
The source connected to the projector is active and available.
Still no image even though you adjust the brightness and/or
the contrast.
Input sources resolution and frequency are supported by the
projector.
Frequency of occurrence   always    sometimes (How often?_____________________)     other (__________________)
Power
No power (POWER indicator does not light green)   See also “WARN-
ING Indicator (WARNING)”.
Power cords plug is fully inserted into the wall outlet.
Main power switch is pressed to the ON position.
Lamp cover is installed correctly .
Lamp counter (lamp operation hours) was cleared after lamp
replacement.
No power even though you press and hold the POWER button
for a minimum of 2 seconds.Shut down during operation.
Power cords plug is fully inserted into the wall outlet.
Lamp cover is installed correctly .
Power Management is turned off (only models with the Power
Management function).
Sleep Timer is turned off (only models with the Sleep Timer
function ).
Video and Audio
Image is too dark.
Remains unchanged even though you adjust the brightness
and/or the contrast.
Image is distorted.
Image appears to be trapezoidal (unchanged even though you
carry out the “Keystone adjustment”).
Parts of the image are lost.
Still unchanged even though you press the AUTO PC button.
Still unchanged even though you carry out “Factory default” in
the projector’s menu.
Image is shifted in the vertical or horizontal direction.
Horizontal and vertical positions are correctly adjusted on a
computer signal.
Input sources resolution and frequency are supported by the
projector.
Some pixels are lost.
Image is flickering.
Still unchanged even though you press the AUTO PC button.
Still unchanged even though you carry out “Factory default” in
the projector’s menu.
Image shows flickering or color drift on a computer signal.
Image appears blurry or out of focus.
Still unchanged even though you checked the signal’s resolu-
tion on PC and changed it to projector’s native resolution.
Still unchanged even though you adjusted the focus.
No sound.
Audio cable is correctly connected to the audio input of the
projector.
Still unchanged even though you adjusted the volume level.
AUDIO OUT is connected to your audio equipment (only mod-
els with the AUDIO OUT connector).
Other
Remote control does not work.
No obstacles between the sensor of the projector and the re-
mote control.
Projector is placed near a fluorescent light that can disturb the
infrared remote controls.
One or more remote sensors are enabled (only models with
the Remote Sensor Selection function).
Batteries are new and are not reversed in installation.
If present on the remote control, projector selector switch is
not used.Buttons on the projector cabinet do not work ( only models with
the Key lock function).
Key lock is not turned on or is disabled in the menu.
Still unchanged even though you press and hold the BACK but-
ton for a minimum of 10 seconds. 
						

							62
7. Appendix
In the space below please describe your problem in detail.
Information on application and environment where your projector is used
Projector
Model number:
Serial No.:
Date of purchase:
Lamp operating time (hours):
Lamp Mode: Normal   Quiet
Information on input signal:
Horizontal sync frequency [          ] kHz
Vertical sync frequency [          ] Hz
Sync polarity H  (+)   (–)
V  (+)   (–)
Sync type Separate   Composite
 Sync on Green
WARNING Indicator:
Steady light Orange   Green
Flashing light [          ] cycles
Remote control model number:
Signal cable
Canon standard or other manufacturer’s cable?
Model number:                        Length:              inch/m
Distribution amplifier
Model number:
Switcher
Model number:
Adapter
Model number:
ProjectorPC
DVD player
Installation environment
Screen size: inch
Screen type: White matte    Beads   Polarization
 Wide angle    High contrast
 Throw distance: feet/inch/m
 Orientation: Ceiling mount    Desktop
Power outlet connection:
Connected directly to wall outlet
Connected to power cord extender or other (the num-
ber of connected equipment______________)
Connected to a power cord reel or other (the number
of connected equipment______________)
Computer
Manufacturer:
Model number:
Notebook PC  / Desktop 
Native resolution:
Refresh rate:
Video adapter:
Other:
Video equipment
VCR, DVD player, Video camera, Video game or other
Manufacturer:
Model number: