Canon projector LV5200 User Manual

21
BASIC OPERATION
Press the NO SHOW button on the Remote Control Unit to black out
the image.  To restore to normal, press the NO SHOW button again or
press any other button.
NO SHOW FUNCTION
Message disappears after 4 seconds.
No show
Press the P-TIMER button on the Remote Control Unit.  The timer
display “00 : 00” appears and the timer starts to count time (00 : 00 ~
59 : 59).  
To stop the P-TIMER display, press the P-TIMER button.  Press the P-
TIMER button again to cancel the P-TIMER function....

22
COMPUTER INPUT (RGB Scart 21-Pin Video Input)
SELECTING THE INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Choose either Computer 1 or Computer 2 by pressing the INPUT
button on the Top Control or on the Remote Control Unit.
If the projector cannot reproduce a proper image, select the correct
input source through the “MENU OPERATION”(see below).
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button to move the red
frame pointer to the INPUT Menu icon.1
Move the...

23
COMPUTER INPUT
SELECTING THE COMPUTER SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, or SXGA (refer to the
“COMPATIBLE COMPUTER SPECIFICATIONS” on page 24).  When selecting Computer, this projector automatically tunes
to the incoming signal and projects a proper image without any special setting.  (Some computers need to be set manually.)
The projector displays one of the Auto, - - -, Mode 1/2/3/4/5, or the system provided in the projector.
When...

24
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
This projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100 MHz of
Dot Clock.
NOTE : The projector may not project a proper image for D-SXGA 2 and D-SXGA 3 depending on some computers.  
Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640...

25
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
The Auto PC Adjustment function automatically adjusts Fine sync, Total dots, Horizontal and Vertical picture position to
conform to your computer.  The Auto PC Adjustment function can be operated as follows.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button to move the red
frame pointer to the PC ADJUST Menu icon.1
2Press the POINT DOWN button to move the red frame pointer to
the AUTO PC Adj. icon and then press...

26
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to the display signals of most personal computers.  However, some computers employ
special signal formats which are different from the standard ones and may not be tuned by the Multi-Scan system of this
projector.  If this happens, the projector cannot reproduce a proper image and the image may be displayed as a flickering
picture, a non-synchronized picture, a non-centered picture, or a skewed picture.
This projector has Manual...

27
COMPUTER INPUT
NOTE
Fine sync, Total dots, Display area (H/V) and Full screen cannot be
adjusted when “1035i (HDTV)” or “1080i (HDTV)” is selected on PC
SYSTEM Menu (P23).
Selects the area displayed with this projector.  Select the resolution
at the display area dialog box.
Display area
Adjustment of the horizontal area displayed with this projector.  Press
the POINT LEFT/RIGHT button(s) to decrease/increase the value.
Display area H
Adjustment of the vertical area displayed with this projector....

28
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (MENU)
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button to move the red
frame pointer to the IMAGE SELECT Menu icon.1
2Press the POINT DOWN button to move the red frame pointer to
the level that you want to set and then press the SET button.
Move the pointer to the level and
press the SET button.
The level being selected.
IMAGE SELECT MENU
Normal picture adjustment preset on this projector....

29
COMPUTER INPUT
Press the POINT LEFT/RIGHT but-
tons to adjust the value.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to move the red
frame pointer to the IMAGE ADJUST Menu icon.1
2Press the POINT DOWN button to move the red frame pointer to
the item that you want to adjust, and then press the SET button.
The level of each item is displayed.  Adjust each level by
pressing the POINT LEFT/RIGHT button(s).
Move the pointer to the item
to be selected and...

30
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has the picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button(s) to move the
red frame pointer to the SCREEN Menu icon.
When Digital zoom + is selected, the ON-SCREEN MENU
disappears and the message “D. Zoom +” is displayed.  Press the
SET button to expand the image size.  And press the POINT
UP/DOWN/LEFT/RIGHT button(s)...