Canon projector LV5110 User Manual

21
BASIC OPERATION
Press the VOLUME (+/–) button on the Remote Control Unit to
adjust the volume.  The Volume dialog box appears on the
screen for a few seconds.The VOLUME (+) button increases
the volume, and the VOLUME (–) button decreases the
volume.
The sound volume can be adjusted through the ON-SCREEN
MENU.  (Refer to page 32.)
Press the MUTE button on the Remote Control Unit to mute the
sound.  To restore the sound to its previous level, press the
MUTE button again or press the VOLUME (+/–)...

22
MODE button
Press the MENU button and the ON-SCREEN MENU will
appear.  
Press the POINT LEFT/RIGHT buttons to select
Computer  and press the SELECT button.  
COMPUTER MODE
SELECTING COMPUTER MODE
MENU OPERATION
When selecting the Computer Mode, the Current Mode display
appears.  It shows the information of the computer of the mode
selected.  
CURRENT MODE DISPLAY
COMPUTER
VIDEO
Providing the information of the computer detected
by the projector.
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTI-SCAN SYSTEM...

23
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and
less than 100 MHz of Dot Clock.
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x...

24
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically tune to the display signals from most personal computers currently distributed.
However, some computers employ special signal formats which are different from the standard ones and may
not be tuned by the Multi-Scan system of this projector.  If this happens, the projector cannot reproduce a proper
image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered
picture or a skewed picture.
This...

25
COMPUTER MODE
The number of the total vertical lines.  Adjust the number to match
the image of your personal computer.
Total lines
Recalls the parameter data that was previously
adjusted.Reset
Stores the parameters in the memory.Stored
Clears the parameter data previously set.Mode free
Closes the PC ADJUST MENU.Quit
The number of the total dots in one horizontal period.  Adjust the
number to match the image of your personal computer.
Total dots
Adjustment of the horizontal or vertical picture...

26
COMPUTER MODE
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select IMAGE
and press the SELECT button.  Another dialog box IMAGE
MENU will appear. 
Press the POINT DOWN button and a red-arrow icon will
appear.  Move the arrow to the item that you want to change by
pressing the POINT UP/DOWN buttons.  To change the value,
press either the POINT RIGHT button or the POINT LEFT
button.
1
2
ADJUST PICTURE IMAGE MANUALLY
Adjust the picture as necessary to...

27
COMPUTER MODE
The Auto Image function is provided to automatically adjust
Fine sync, Total dots, and Picture Position for most computers.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select AUTO
IMAGE  and press the SELECT button.  
Another dialog box AUTO IMAGE MENU will appear. 
Move the arrow to an item that you want to adjust by pressing
the POINT UP/DOWN button.  Change the setting On or Off by
pressing the SELECT button.  
1
2
AUTO IMAGE...

28
COMPUTER MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select
SCREEN  and press the SELECT button.  Another dialog
box SCREEN MENU will appear.
To adjust the image size or pan the image, select Digital zoom in the
dialog box.  The ON-SCREEN MENU and SCREEN MENU
disappears and the message “D. Zoom” is displayed....

29
MODE button
VIDEO MODE
Press the MENU button and the ON-SCREEN MENU will
appear.  
Press the POINT LEFT/RIGHT buttons to select Video
and press the SELECT button.  
SELECTING VIDEO MODE
DIRECT OPERATION
Select VIDEO mode by pressing the MODE button on the Top
Control or the VIDEO button on the Remote Control Unit.
MENU OPERATION
COMPUTER
VIDEO
This projector automatically detects the signal from the VIDEO
INPUT JACK(s) or the S-VIDEO INPUT JACK.  When those
jacks are connected at the same time, select...

30
VIDEO MODE
SELECTING COLOR SYSTEM
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button.  Another dialog box
SYSTEM MENU will appear. 
Press the POINT DOWN button and a red-arrow icon will
appear.  Move the arrow to Auto, and then press the 
SELECT
button.  
1
2
The projector automatically detects the incoming Video system, and
adjusts itself to optimize its performance.
When the Video System is PAL-M or PAL-N, select...