Canon projector LV5110 User Manual
Have a look at the manual Canon projector LV5110 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 BASIC OPERATION Press the VOLUME (+/–) button on the Remote Control Unit to adjust the volume. The Volume dialog box appears on the screen for a few seconds.The VOLUME (+) button increases the volume, and the VOLUME (–) button decreases the volume. The sound volume can be adjusted through the ON-SCREEN MENU. (Refer to page 32.) Press the MUTE button on the Remote Control Unit to mute the sound. To restore the sound to its previous level, press the MUTE button again or press the VOLUME (+/–) button. The sound mute can be set through the ON-SCREEN MENU. (Refer to page 32.) SOUND ADJUSTMENT Press the FREEZE button on the Remote Control Unit to freeze the picture on-screen. This function is cancelled when the FREEZE button is pressed again or any other function button is pressed. Press the NO SHOW button on the Remote Control Unit to black out the image. This function is cancelled when the NO SHOW button is pressed again or any other function button is pressed. NO SHOW FUNCTION PICTURE FREEZE FUNCTION SOUND MUTE ADJUSTMENT SOUND VOLUME ADJUSTMENTIndicates the level of the volume. Press the MUTE button to turn the Mute function On or Off. The display disappears after 4 seconds. The message disappears after 4 seconds. No show Press the P-TIMER button on the Remote Control unit. The timer display “00 : 00” appears on the screen and the timer starts to count the time (00 : 00 ~ 59 : 59). To stop the P-TIMER, press the P-TIMER button. And then, press the P-TIMER button again to cancel the P-TIMER function. P-TIMER FUNCTION
22 MODE button Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Computer and press the SELECT button. COMPUTER MODE SELECTING COMPUTER MODE MENU OPERATION When selecting the Computer Mode, the Current Mode display appears. It shows the information of the computer of the mode selected. CURRENT MODE DISPLAY COMPUTER VIDEO Providing the information of the computer detected by the projector. SELECTING COMPUTER SYSTEM AUTOMATIC MULTI-SCAN SYSTEM This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to “COMPATIBLE COMPUTER SPECIFICATION” on page 23). When selecting Computer, this projector automatically tunes to the incoming signal and projects the proper image without any special settings. (Setting of the Computer System may be required when connecting some computers.) Note : The projector may display one of the following messages. The projector cannot discriminate or detect the input signal from the computer. Adjust and set the computer system manually. (Refer to page 24.) There is no signal input from the computer. Make sure the connection of the computer and the projector is set correctly. (Refer to TROUBLESHOOTING on page 37.) Go to PC adj. No signal SELECT COMPUTER SYSTEM MANUALLY To set the Computer system manually, select the mode on the ON-SCREEN MENU. Displays the SYSTEM being selected. SYSTEM BOX The system being selected. The systems on these dialog boxes can be selected. Closes SYSTEM MENU. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Another dialog box SYSTEM MENU will appear. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the system that you want to set, and then press SELECT button. 1 2 DIRECT OPERATION Select COMPUTER mode by pressing the MODE button on the Top Control or the COMPUTER button on the Remote Control Unit.
23 COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100 MHz of Dot Clock. NOTE : Specifications are subject to change without notice. ON-SCREEN DISPLAYRESOLUTIONH-Freq. (kHz)V-Freq. (Hz) VGA 1640 x 48031.4759.88 VGA 2720 x 40031.4770.09 VGA 3640 x 40031.4770.09 VGA 4640 x 48037.8674.38 VGA 5640 x 48037.8672.81 VGA 6640 x 48037.5075.00 MAC LC13640 x 48034.9766.60 MAC 13640 x 48035.0066.67 MAC1 6832 x 62449.7274.55 MAC 191024 x 76860.2475.08 MAC 211152 x 87068.6875.06 SVGA 1800 x 60035.15656.25 SVGA 2800 x 60037.8860.32 SVGA 3800 x 60046.87575.00 SVGA 4800 x 60053.67485.06 SVGA 5800 x 60048.0872.19 SVGA 6800 x 60037.9061.03 SVGA 7800 x 60034.5055.38 SVGA 8800 x 60038.0060.51 SVGA 9800 x 60038.6060.31 SVGA 10800 x 60032.7051.09 SVGA 11800 x 60038.0060.51 ON-SCREEN DISPLAYRESOLUTIONH-Freq. (kHz)V-Freq. (Hz) XGA 101024 x 768 XGA 111024 x 768 XGA 121024 x 768 (Interlace) XGA 131024 x 768 62.0477.07 XGA 141024 x 768 61.0075.70 XGA151024 x 768 35.52243.48 46.9058.20 XGA 81024 x 768 47.0058.30 XGA 91024 x 768 (Interlace) 58.0372.00 SXGA 11152 x 864 63.4879.35 36.0043.59 64.2070.40 SXGA 111152 x 900 SXGA 131280 x 1024 (Interlace) SXGA 141280 x 1024 (Interlace) 61.2065.20 50.0043.00 HDTV720p––––– 50.0047.00 45.0060.00 XGA 11024 x 768 XGA 21024 x 768 XGA 31024 x 768 XGA 41024 x 768 48.3660.00 68.67784.997 XGA 61024 x 768 60.02375.03 XGA 71024 x 768 56.47670.07 48.5060.02 44.0054.58 SXGA 171152 x 900 SXGA 181280 x 1024 (Interlace) 61.8566.00 46.4343.35 XGA 51024 x 76860.3174.92 VGA 7640 x 48043.26985.00 RGB–––––15.62525 RGB–––––15.73430 HDTV1080i–––––33.7560.00 HDTV1035i–––––33.7560.00
24 COMPUTER MODE PC ADJUSTMENT This Projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by the Multi-Scan system of this projector. If this happens, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match with those special signal formats. This projector has five independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. Note : This PC ADJUSTMENT function cannot be operated when “RGB,” “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P22 and 23). Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT RIGHT/LEFT buttons to select PC ADJUST and press the SELECT button. Another dialog box “Where to reserve” MENU will appear. In this dialog box, you can store the parameter into the area from “Mode 1” to “Mode 5.” When memorizing the new computer parameter, select the Mode with the message “Free” by pressing the POINT UP/DOWN buttons and the SELECT button. To change the parameters of the Mode previously set, select the Mode with “Stored.” 1 2 When the Mode is selected, Parameter adjustment dialog box appears. Move the arrow to the item that you want to change by pressing the POINT UP/DOWN buttons, and adjust each item to match with your computer. To change the value, press either the POINT RIGHT / LEFT button. Refer to the next page for adjusting each item. 3 Move the arrow to “Stored” and press the SELECT button. The parameter is memorized in the selected Mode.4 This Mode has parameters being stored. Closes the menu.The Vacant Mode. Manual set Computer Mode (1 to 5). Press the POINT RIGHT/LEFT button(s) to adjust the value. Press the SELECT button to set Full screen function on/off. To activate the Mode manually adjusted in this PC ADJUSTMENT MENU, select the Mode at the SYSTEM SELECT MENU. (Refer to page 22.)5
25 COMPUTER MODE The number of the total vertical lines. Adjust the number to match the image of your personal computer. Total lines Recalls the parameter data that was previously adjusted.Reset Stores the parameters in the memory.Stored Clears the parameter data previously set.Mode free Closes the PC ADJUST MENU.Quit The number of the total dots in one horizontal period. Adjust the number to match the image of your personal computer. Total dots Adjustment of the horizontal or vertical picture position. When the image is not centered on the screen, adjust each of those items. Horizontal / Vertical Adjustment of the clamp level. When the image has a dark bar(s), try this adjustment. Clamp Adjustment of the area displayed with this projector. Select the resolution at the Display area dialog box, or adjust the number at the column of “H” or “V” to match the resolution of the image. Display area Set “On” to resize the image with 4 x 3 aspect ratio to fit the screen. Full Screen Each of the keys operates as follow. Press the SELECT button to select the typical resolution of the image.
26 COMPUTER MODE Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT button. Another dialog box IMAGE MENU will appear. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item that you want to change by pressing the POINT UP/DOWN buttons. To change the value, press either the POINT RIGHT button or the POINT LEFT button. 1 2 ADJUST PICTURE IMAGE MANUALLY Adjust the picture as necessary to eliminate flicker from the display. (From 0 to 255.) The number of the total dots in one horizontal period. Adjust the number to match your PC image. Press POINT LEFT button to decrease contrast, and press POINT RIGHT button to increase contrast. (From 0 to 63.) Press POINT LEFT button to adjust the image darker, and press POINT RIGHT button to adjust brighter. (From 0 to 63.) Closes IMAGE MENU.Move the arrow to the item and press POINT RIGHT / LEFT button. Recalls the data previously adjusted.Reset Stores the adjusted data in the memory.Stored Closes the PICTURE IMAGE ADJUSTMENT MENU.Quit Move the arrow to the color that you want to adjust. Press POINT LEFT button to lighten the color and press POINT RIGHT button to deepen the color. (From 0 to 63.) Each of the keys operates as follow. Fine sync Total dots White balance (Red / Green / Blue) Contrast Brightness The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The “Normal” display will be displayed on the screen for a few seconds. NORMAL FUNCTION Normal Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 16.) Gamma PICTURE IMAGE ADJUSTMENTS NOTE : The Fine sync and the Total dots cannot be fully adjusted when “RGB,” “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P22 and 23).
27 COMPUTER MODE The Auto Image function is provided to automatically adjust Fine sync, Total dots, and Picture Position for most computers. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select AUTO IMAGE and press the SELECT button. Another dialog box AUTO IMAGE MENU will appear. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN button. Change the setting On or Off by pressing the SELECT button. 1 2 AUTO IMAGE FUNCTION Move the arrow to “Go!” and press the SELECT button to start the Auto Image function. This adjustment can be executed by pressing AUTO IMAGE button on the Remote Control Unit.3 NOTE : The Fine sync and the Total dots cannot be fully adjusted when “RGB,” “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P22 and 23). The Fine sync, Total dots, and Picture Position of some computers may not be fully adjusted with the Auto Image Function. In that case, manual adjustment is required to make fine image. (Refer to page 26 to adjust Fine sync or Total dots and page 27 to adjust Picture Position.) Closes AUTO IMAGE MENU.Move the arrow to the item and then press the SELECT button. Starts the adjustment on the item set to On. Adjust the picture as necessary to eliminate flicker from the display. This item can be adjusted manually. (Refer to page 26.) The number of the total dots in one horizontal period. This item can be adjusted manually. (Refer to page 26.) Adjustment of the position of the image. This item can be adjusted manually. (Refer to page 27.) Fine sync Total dots Position Stores the On/Off setting of each item.Stored Starts the Auto Image Function.Go! Closes the AUTO IMAGE MENU.Quit PICTURE POSITION ADJUSTMENT The position of the image can be adjusted vertically and horizontally through PICTURE POSITION ADJUSTMENT. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select POSITION and press the SELECT button. The PICTURE POSITION DIALOG BOX will appear. Move the image by pressing the POINT UP / DOWN / RIGHT / LEFT buttons. 1 2 PICTURE POSITIONDIALOG BOX Press the POINT UP / DOWN / RIGHT / LEFT buttons to move the imageTo cancel PICTURE POSITION ADJUSTMENT, press any button except POINT buttons. To return to the position previously set, press NORMAL button.
28 COMPUTER MODE PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the desirable image size. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT button. Another dialog box SCREEN MENU will appear. To adjust the image size or pan the image, select Digital zoom in the dialog box. The ON-SCREEN MENU and SCREEN MENU disappears and the message “D. Zoom” is displayed. This projector also enters Digital Zoom mode by pressing the D.ZOOM /button on the Remote Control Unit. Refer to the following for operation. 1 This projector cannot display any resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting the projector. The image data in other than SVGA (800 x 600) is modified to fit the screen size in the initial mode. The normal Panning Operation may not function properly if the computer system prepared with the PC Adjust is used. Expand function To expand the image size, press the D.ZOOM button or the SELECT button. The image is magnified by degrees. Compress function To compress the image size, press the D.ZOOM button or the RIGHT CLICK button. The size of image is reduced by degrees. Panning function To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is larger than the screen size. To cancel Digital Zoom mode, press any button except D.ZOOM /, SELECT, RIGHT CLICK, or POINT button. To adjust the image to 800 x 600, press NORMAL button. To make the image into its original size select True in the dialog box. When the original image size is larger than the screen size (800 x 600), this projector enters Digital Zoom mode automatically. Move the arrow to the function and press the SELECT button. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the function that you want to select and then press SELECT button.2 True Digital Zoom Keystone When the image is distorted vertically, select Keystone in the dialog box. The ON-SCREEN MENU and SCREEN MENU disappears and the message “Keystone” is displayed. Correct the Keystone distortion by pressing the KEYSTONE /button or the POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on page 20.NOTE : The True and the Digital Zoom cannot be operated when “RGB,” “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P22 and 23).
29 MODE button VIDEO MODE Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Video and press the SELECT button. SELECTING VIDEO MODE DIRECT OPERATION Select VIDEO mode by pressing the MODE button on the Top Control or the VIDEO button on the Remote Control Unit. MENU OPERATION COMPUTER VIDEO This projector automatically detects the signal from the VIDEO INPUT JACK(s) or the S-VIDEO INPUT JACK. When those jacks are connected at the same time, select the type of Video source in VIDEO SOURCE MENU. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select VIDEO SOURCE and press the SELECT button. Another dialog box VIDEO SOURCE MENU will appear. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the source that you want to select, and then press the SELECT button. 1 2 This box indicates the Video source being selected. SELECTING VIDEO SOURCE Video / S-Video / Y, Pb/Cb, Pr/Cr The projector automatically detects the incoming Video source, and adjusts itself to optimize its performance. •When both VIDEO jack and S-VIDEO jack are connected, the S- VIDEO jack has priority over the VIDEO jack. •When both Y-Pb/Cb-Pr/Cr jacks and S-VIDEO jack are connected, the Y-Pb/Cb-Pr/Cr jacks have priority over the S-VIDEO jack. Auto When the VIDEO INPUT JACK(s) and the S-VIDEO INPUT JACK are connected at the same time, or if the projector cannot chose the proper video source, it is necessary to select a specific video source among Video, S-Video and Y, Pb/Cb, Pr/Cr.
30 VIDEO MODE SELECTING COLOR SYSTEM Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Another dialog box SYSTEM MENU will appear. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Auto, and then press the SELECT button. 1 2 The projector automatically detects the incoming Video system, and adjusts itself to optimize its performance. When the Video System is PAL-M or PAL-N, select the system manually. If the projector cannot reproduce the proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.Move the arrow to the Mode and press the SELECT button. PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the desirable image size. Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT button. Another dialog box SCREEN MENU will appear. Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the screen size that you want to set, and then press the SELECT button. 1 2 Normal Video Image size with 4 x 3 aspect ratio. Resizes the image for wide screen size with 16 x 9 aspect ratio. Move the pointer to the function and press the SELECT button.Regular Wide Keystone When the image is distorted vertically, select Keystone in the dialog box. Correct the Keystone distortion by pressing KEYSTONE / button or POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on page 20. This box indicates the system being selected. Move the arrow to the Mode and press the SELECT button. This box indicates the system being selected. Auto PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N The projector automatically detects the incoming Video signal, and adjusts itself to optimize its performance. If the projector cannot reproduce the proper video image, it is necessary to select a specific component video signal format among 480i, 575i, 480p, 575p, 720p, 1035i and 1080i. Auto COMPONENT VIDEO SIGNAL FORMAT When the Video signal is from the VIDEO or the S-VIDEO JACK When the Video signal is from the Y, Pb/Cb, Pr/Cr JACKS NOTE : The Regular and the Wide cannot be operated when “720p,” “1035i” or “1080i” is selected on SYSTEM MENU (above).