Canon Projector Lv-7585 User Manual

							
61

This projector uses a high-pressure lamp which must be handled carefully and properly. 
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp  lifetime  may  differ  from  lamp  to  lamp  and  according  to  the  environment  of  use. There  is  no 
guarantee  of  the  same  lifetime  for  each  lamp.  Some  lamps  may  fail  or  terminate  their  lifetime  in  a 
shorter period of time than other similar lamps.
● If  the  projector  indicates  that  the  lamp  should  be  replaced,  i.e.,  if  the  LAMP  REPLACE  indicator  lights 
up,  replace  the  lamp  with  a  new  one  IMMEDIATELY  after  the  projector  has  cooled  down.  (Follow 
carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp 
with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.  
● Lamp  may  explode  as  a  result  of  vibration,  shock  or  degradation  as  a  result  of  hours  of  use  as  its 
lifetime  draws  to  an  end.  Risk  of  explosion  may  differ  according  to  the  environment  or  conditions  in 
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFET y PRECAUTIONS SHOULD BE TAKEN .
If  a  lamp  explodes,  disconnect  the  projector’s  AC  plug  from  the  AC  outlet  immediately.  Contact  an 
authorized  service  station  for  a  checkup  of  the  unit  and  replacement  of  the  lamp.  Additionally,  check 
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out 
from  the  cooling  air  circulation  holes.  Any  broken  shards  found  should  be  cleaned  up  carefully.  No  one 
should  check  the  inside  of  the  projector  except  those  who  are  authorized  trained  technicians  and  who 
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those 
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken 
glass.
          LAMP HANDLING PRECAUTIONS
Maintenance and Care 
						

							
6

Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens 
cleaner, or use a lens cleaning paper or commercially 
available air blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the lens.
Cleaning the Projector Cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning 
cloth. When the cabinet is heavily soiled, use a small amount 
of mild detergent and finish with a soft dry cleaning cloth. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the cabinet.
When the projector is not in use, put the projector in 
an appropriate carrying case to protect it from dust and 
scratches.
Cleaning the Projection Lens
Maintenance and Care 
						

							
6

The WARNING indicators show the state of the function which protects the projector. Check the state of the 
WARNING indicators and the POWER indicator to take proper maintenance. 
Warning Indicators
The projector is shut down and the WARNING TEMP. 
indicator is blinking red.
When the temperature inside the projector reaches a 
certain level, the projector will be automatically shut down 
to protect the inside of the projector. The LAMP indicator 
turns red and the WARNING TEMP indicator blinks while 
the projector is being cooled down. When the projector has 
cooled down enough (to its normal operating temperature), 
it can be turned on again by pressing the POWER button.
✔Note:
	•	 The	WARNING	 TEMP.	indicator	continues	to	blink	even	after	the	
temperature	inside	the	projector	returns	to	normal.	 When	the	
projector	is	turned	on	again,	the	 WARNING	TEMP.	indicator	stops	
blinking.	
Then check the matters below:
–   Did you provide appropriate space for the projector to be 
ventilated? Check the installing condition to see if the air 
vents of the projector are not blocked.
–   Has the projector been installed near an Air-Conditioning/ 
Heating Duct or Vent? Move the installation of the 
projector away from the duct or vent.
–   Is the filter clean? Replace the filter with a new one.
The projector is shut down; and the LAMP indicator is 
lighting and other four indicators are blinking.
When the projector detects an abnormal condition, it will 
be automatically shut down to protect the inside of the 
projector and the LAMP indicator lights on and other four 
indicators blink. In this case, unplug the AC power cord and 
plug it, and then turn on the projector once again to verify 
operation. If the projector cannot be turned on and these 
indicators are still lighting and blinking, unplug the AC power 
cord and contact the service station.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE 
AC POWER CORD CONNECTED UNDER AN 
ABNORMAL CONDITION. IT MAY RESULT IN FIRE 
OR ELECTRIC SHOCK.
Top Panel
LAMP indicator lights on 
and other four indicators 
blink
Top Panel
WARNING TEMP  .
blinking red
Maintenance and CareMaintenance and Care 
						

							
64

Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–21.
2.  Check the cable connection. Make sure that all computers, video equipment, and power cords are properly 
connected.
3.  Make sure that all power is switched on.
4.  If the projector still does not produce an image, restart your computer.
5.  If an image still does not appear, disconnect the projector from your computer and check your computer 
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector. 
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the 
projector. Turn on equipment in the order of the projector and computer.)
6.  If a problem still persists, check the following solutions.
No power  .● Plug the power cord of the projector into the AC outlet.
● Wait  until  the  POWER  indicator  stops  blinking  to  turn  on  the  projector  again.  (See  page 
23)
●  Check  the  WARNING TEMP.  indicator.  If  the  WARNING TEMP.  indicator  is  blinking,  the 
projector cannot be turned on. (See page 63.)
● Check the projection lamp. (See page 59.)
● Unlock the Key lock function for the projector.  (See page 53)
● See if the filter cartridge is inserted. (See page 57)
Image is out of focus .● Adjust the focus of the projector.
● Make sure the projection screen is at least 4.6’ (1.4 m) away from the projector.
● Check the projection lens to see if it needs cleaning.
NOTE:   Moving  the  projector  from  a  cool  to  a  warm  place  may  result  in  moisture 
condensation  on  the  projection  lens.  If  this  happens,  leave  the  projector  off  and 
wait until condensation evaporates.
Picture is left/right 
reversed .● Check the Ceiling/Rear function. (See pages 40, 44)
Problem:Try These Solutions
Picture is top/bottom 
reversed .● Check the Ceiling function. (See pages 40, 44.)
Some displays are 
not seen during 
operations .
● Check the Display function. (See page 48.)
No image .● Check the connection between your computer or video equipment and the projector.
● It takes about 30 seconds to display an image after turning on the projector.
● See if the selected system is corresponding with your computer or video equipment.
● Make sure the temperature is not out of specified operating temperature (41˚F–104˚F
    [5˚C–40˚C]).
Appendix
appears on the 
screen
● The  end  of  lamp  life  is  approaching.  Replace  the  lamp  with  a  new  one  promptly.    (See 
page 59)
appears on the 
screen
● The filter is out of scroll. Replace the filter cartridge with a new one promptly. (See pages 
56-57) 
						

							
65

WARNING: 
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector 
or  the  service  center.  Specify  the  model  number  and  explain  about  the  problem. We  will  advise  you  how  to  obtain 
service.
Remote control unit 
does not work .●  Check the batteries.
● 
Check if the ALL-OFF switch on the remote control unit is set to “ON.”
●  Check if the RC sensor is set properly. (See page 51)
●  Make sure no obstruction is between the projector and the remote control unit.
●  Make sure you are not too far from the projector when using the remote control unit.
    Maximum operating range is 16.4’ (5 m).
● Make sure that the remote control code conforms to the projector’s code.
    (See page 51.)
● Unlock the Key lock function for the remote control unit. (See page 53).
●  Wireless remote control unit does not work when the remote control cable is connected 
to the projector. (See page 15).
Problem:Try These Solutions
Wireless mouse 
function does not 
work .
● Check the cable connection between the projector and your computer.
● Check the mouse setting on your computer.
● Turn on the projector before you turn on the computer.
Unable to unlock the 
Logo PIN code lock, 
Security key lock or 
Security PIN code 
lock .
● Contact the service station.
appears on the 
screen
● Your operation is invalid. Operate correctly.
Appendix 
						

							
66

Menu Tree
InputRGB (PC analog)Go to System (1)Input 1
Y, Pb/Cb,Pr/Cr
Computer Input/Video Input
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
Network
Video
RGB
Go to System (2)
Go to System (3)
Go to System (1)
Go to System (2)Video
Y, Pb/Cb,Pr/Cr
S-video
Go to System (3)
Go to System (2)
Input 2
Input 3
Go to System (1)
InputH-sync freq.V-sync freq.
PIN code lock
Information
Key lock
ScreenLanguageLamp statusPower managementSecurity
Remote control code
Quit
0–630–63
Off/On/Film
Image AdjustContrastBrightnessColor ]Tint ]
RedGreenBlue
Sharpness
ResetStore
Gamma
Progressive ]
0–630–630–63
0–31 0–15
Custom 1
Yes / No
Quit
Off/OnNoise reduction ]
0–630–63
✔Note:
 •	 The	Menu	display	varies	depending	on	the	input	signal.
InformationImage Adjust
]Displayed	only	in	Video	Input
HighMidLow
XLow
Adj.
Color temp.
Appendix
Colormanagement
Auto picture controlOff/L1/L2
HighMidLow
Color temp.
OffsetRed/Green/Blue
Custom 10
Color
Gamma
ListColor M.
Menu
MidLow
Color M.
All DelMenu 
						

							
67

Computer Input
System (1)Mode 1
Mode 2
Image SelectStandard
High contrast
Custom 1
Custom 10
ScreenNormal
True
Wide
Full screen
Digital zoom +
Digital zoom -
PC AdjustAuto PC adj.
Fine sync.
Total dots
Position H
Position V
Current mode
Clamp
Display area - H
Display area - V
Reset
Mode free
Store
Quit
0–31
Yes/No
Mode 1
Mode 10
Quit
] System displayed in the System Menu varies depending on the input signal.
✔Note:
 •	 The	Menu	display	varies	depending	on	the	input	signal.
SVGA 1
SVGA 2
SVGA 3
Rear
Keystone
CeilingResetStore
On/OffOn/Off
CustomH & VScale
Position
H / VOn/OffH / VCommonReset
Video Input
System (2)Auto
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
System (3)Auto
1080i
1035i
720p
575p
480p
575i
480i
Image SelectStandard
Cinema
Custom 1
Custom 10
ScreenNormal
Wide
Rear
Keystone
CeilingResetStore
On/OffOn/Off
CustomH & VScale
Position
H / VOn/OffH / VCommonReset
Reset
Reset
Appendix
Quit
Quit 
						

							
68

Computer Input/Video Input
SettingLanguage
Fan control
Quit
Position/Simple Menu
Blue/User/Black
Logo select
Capture
Logo PIN code lock
Quit
Auto mode/Normal mode /Eco 1 mode/Eco 2 mode
Yes/No
12 languages provided.
Menu
Logo
Lamp mode
Filter control
Both/Front/Back
Normal/Max
Power management
Background
On/Off
Logo PIN code change
Quit
RC sensor
Ready
Off
Shut down
1–30 Min.
Quit
On/OffOn start
Pointer
Key lockSecurityOff
Projector
Remote Control
PIN code lockOff/On1/On2
PIN code change
Used timeFilter counter
Yes/NoFactory default
Quit
On/Countdown Off/OffDisplay
User/Default/Off
Yes/No
Code 1Remote Control
Code 8
Quit
MouseUSB
Projector
Arrow/Cross/Dot
Off/400H/700H/1000H
ResetYes/No
Quit
Scrolls remainingScroll(s)
ResetYes/No
Quit
8 test patterns providedTest patternQuit
Lamp counterHour(s)
Quit
ResetYes/No
Appendix
Quit 
						

							
69

Indicators and Projector Condition
Check the indicators for the projector condition.  
Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
LAMPREPLACE
orange
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the POWER button 
to turn on the projector.
The projector is operating normally.
The projector is preparing for stand-by or the projection lamp 
is being cooled down. The projector cannot be turned on until 
cooling is completed and the POWER indicator lights green.
The projector is in the Power management mode.
The filter is scrolled using the FILTER button on the remote 
control unit or the Filter control function in the setting menu. 
When the filter is being scrolled, the Filter replacement icon 
and “Please wait...” message (Fig. 1) appear on the screen for 
10 seconds.
The projector is operating normally .
Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
LAMPREPLACE
orange
The temperature inside the projector is elevated close to the 
abnormally high level.
The temperature inside the projector is abnormally high. The 
projector cannot be turned on. When the projector is cooled 
down enough and the temperature returns to normal, the 
POWER indicator lights green and the projector can be turned 
on. (The WARNING TEMP. indicator keeps blinking.) Check and 
replace the filter.
The projector is detecting abnormal condition .
• • • on
• • • off
• • •  blinking at the normal rate       
(approx. 1 second ON,         
1 second OFF)• • • dim
• • •  blinking slow           
(approx. 2 seconds ON, 
2 seconds OFF)
• • • blinking fast              
(approx. 0.5 seconds ON,  
0.5 seconds OFF)
]
]
]
]
]
]
]
Appendix
Fig .1    Filter replacement icon and “Please wait...”
v
v
v
v
v
v
v
v 
						

							
70

Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
LAMPREPLACE
orange
The projector has been cooled down enough and the 
temperature returns to normal. When turning on the projector, 
the WARNING TEMP. indicator stops blinking. Check and 
replace the filter.
The lamp cannot light up. (The projector is preparing for stand-
by or the projection lamp is being cooled down. The projector 
cannot be turned on until cooling is completed.)
The lamp cannot light up. (The lamp has been cooled down 
enough and the projector is in stand-by mode and ready to be 
turned on with the POWER button.)
The lamp has been used overtime. Replace the lamp 
immediately and then reset the lamp counter. The indicator 
will be turned off after resetting the counter.
If the Filter counter reached a time set in the timer setting, 
a Filter replacement icon (Fig.2) appears on the screen and 
the WARNING FILTER indicator on the top panel lights up. 
Replace the filter as soon as possible. If the filter is out of 
scroll and the projector reaches a time set in the timer setting, 
Fig. 3 appears on the screen and the WARNING FILTER 
indicator lights up. Replace the filter cartridge as soon as 
possible.
If the filter is clogged and no scroll is left in the filter cartridge, 
a Filter cartridge replacement icon (Fig.4) appears on the 
screen and the WARNING FILTER indicator lights up. Replace 
the filter cartridge as soon as possible.
✔Note:	 •	 Fig.2,	Fig.3	and	Fig.4	icon	will	not	appear	when	the	Display	function	is	set	to	 “Off”	(p.48),	during	 “Freeze”	(p.28),	or	“Blank”	(p.29).
The filter cartridge is not installed in the projector. Check the 
filter compartment to see if the filter cartridge is installed in 
the projector. When the filter cartridge is installed and the 
indicators continue to light and blink, read the column below.
The projector detects an abnormal condition and cannot be 
turned on. Unplug the AC power cord and plug it again to turn 
on the projector. If the projector is turned off again, unplug the 
AC power cord and contact the dealer or the service center. 
Do not leave the projector on. It may cause an electric shock 
or a fire hazard.
Fig .   Filter replacement icon
 When the filter detects clogging, reaches a time set in the timer setting or runs out of the filter scroll, the WARNING 
FILTER indicator lights orange. When this indicator lights orange, replace the filter or the filter cart\
ridge with a new one 
promptly. Reset the Filter counter and Scroll counter after replacing the filter cartridge (p.58). 
  When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights
 orange. When this indicator lights 
orange, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp (p.59).
Fig .4    Filter cartridge replacement icon
]
]
]
]
]
Appendix
v
v
v
Fig .