Canon Projector Lv-7585 User Manual

							
1

RGB Scart21-pin Output
Connecting to Video Equipment (Video, S-Video)
S-video cable
S-video OutputComposite Video
Y - Pb/Cb - Pr/Cr
BNC cable
Unplug	the	power	cords	
of	both	the	projector	
and	external	equipment	
from	the	AC	outlet	before	
connecting	cables.
Cables used for connection (] = Cables not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) ]
• BNC Cable ]
• S-VIDEO Cable ]
• Scart-VGA Cable    ]
Component Video OutputComposite Video
Component Video Output(Y, Pb/Cb, Cr/Pr)
Digital Output(HDCP compatible)
RCA cableDVI-Digital cableScart-VGA cable
VideoVideoY - Pb/Cb - Pr/CrDIGITAL INANALOG INMONITOR OUTS-VIDEO
Installation
Input TerminalMonitor OutCable
Input 1
D-sub15RGB (PC analog)YES
RGB (SCART)NO
DVI-DRGB (PC digital)NO
RGB (AV HDCP)NO
Input 25BNC
RGBYES
VideoYESQ
Y, Cb/CrYESQ
Input 3
RCAY, Cb/CrYESQ
S-VideoS-videoNO
VideoVideoYESQ
NetworkNO
Monitor Out Signal Table
Refer to the Monitor Out Signal Table (above).
Q
A cable with one end D-sub 15 and the other end (Black box) compatible with each equipment is necessary.  
						

							


This projector uses nominal input voltages of 100–120 V or 200–
240 V AC and it automatically selects the correct input voltage. It 
is designed to work with single-phase power systems having a 
grounded neutral conductor. To reduce the risk of electrical shock, 
do not plug into any other type of power system.
If you are not sure of the type of power being supplied, consult 
your authorized dealer or service station.
Connect the projector with all peripheral equipment before turning 
on the projector. 
 CAUTION
For safety, unplug the AC power cord when the projector is not 
in use. When the projector is connected to an outlet with AC 
power cord, it is in stand-by mode and consumes a little electric 
power.
Connecting the AC Power Cord
Connect  the  AC  power  cord  (supplied)  to  the 
projector.
The  AC  outlet  must  be  near  this  equipment  and 
must be easily accessible.
Installation
NOTE ON THE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector sideAC Outlet side
To POWER CORD CONNECTOR on your projector.
Ground
To the AC Outlet.
(10 V AC)
For Continental EuropeFor the U .S .A .  and CanadaFor the U  .K .
To the AC Outlet.
(00–40 V AC)To the AC Outlet.
(00–40 V AC) 
						

							


Turning On the Projector
Connect the projector’s AC power cord into an AC 
outlet. The LAMP indicator lights red and the POWER 
indicator lights green.
Press the POWER button on the side control or the 
ON button on the remote control unit. The LAMP 
indicator dims and the cooling fans start to operate. 
The preparation display appears on the screen and the 
countdown starts. 
2
3
1
The preparation display will disappear after 30 seconds.
4After the countdown, the input source that was 
selected the last time and the Lamp mode status icon 
(see page 51) appear on the screen.
If the projector is locked with a PIN code, PIN code 
Input Dialog Box will appear. Enter the PIN code as 
instructed below.
Selected Input Source and Lamp mode
Complete peripheral connections (with a computer, 
VCR, etc.) before turning on the projector.  
What is PIN code?
PIN (Personal Identification Number) code is a security 
code that allows the person who knows it to operate the 
projector. Setting a PIN code prevents unauthorized use of 
the projector. 
A PIN code consists of a four-digit number. Refer to the PIN 
code lock function in the Setting Menu on page 53-54 for 
locking operation of the projector with your PIN code.
PIN code Input Dialog Box
Enter a PIN code
After the OK icon disappears, you can operate the projector.  
Lamp mode status
See page 51 for the Lamp mode status
✔Note:	 •	The	Lamp	replacement	icon	and	the	Filter	
replacement	or	the	Filter	cartridge	replacement	
icon	may	appear	on	the	screen	depending	on	the	
usage	state	of	the	projector.
	•	 When	the	filter	cartridge	replacement	icon	
keeps	appearing	on	the	screen	at	turning	on	the	
projector	for	some	time	and	no	action	is	taken	
to	replace	the	filter	cartridge,	the	projector	will	
be	automatically	shut	down	in	3	minutes	after	
turning	on	 to	protect	the	projector.	(pp.	56-58,	70)Use the Point ed buttons on the side control or Number 
buttons on the remote control unit to enter a number. 
When using side control
Use the Point ed buttons on the side control to select a 
number. Press the Point 8 button to fix the number and 
move the red frame pointer to the next box. The number 
changes to “✳.” Repeat this step to complete entering a 
four-digit number. After entering the four-digit number, move 
the pointer to “Set.” Press the OK button so that you can 
start to operate the projector.
When using remote control unit
Press the Number buttons on the remote control unit to 
enter a number (p.14). When you complete entering a four-
digit number, the pointer moves to “Set.” Press the OK 
button so that you can start to operate the projector.
 If you fixed an incorrect number, use the Point 7 button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
If you entered an incorrect PIN code, “PIN code” and the 
number (✳✳✳✳) will turn red for a moment. Enter the 
correct PIN code all over again.
✔Note:
	 •	 When	the	Logo	select	function	is	set	to	 “Off,”	the	
logo	will	not	be	shown	on	the	screen	(p.49).
	 •	 When	the	 “Countdown	off”	or	 “Off”	is	selected	
in	the	Display	function,	the	countdown	will	not	
be	shown	on	the	screen	(p.48).
	 •	 During	the	countdown	period,	all	operations	are	invalid.	•	 If	the	correct	PIN	code	number	is	not	entered	
within	three	minutes	after	the	PIN	code	dialog	
box	appeared,	the	projector	will	be	turned	off	
automatically.	•	 The	 “1234”	is	set	as	the	initial	PIN	code	at	the	factory.
Basic Operation
16 
						

							
4

Press the POWER button on the side control or the 
STAND-BY button on the remote control unit, and 
“Power off?” appears on the screen.
Press the POWER button on the side control or the 
STAND-BY button on the remote control unit again to 
turn off the projector. The LAMP indicator lights bright 
and the POWER indicator turns off. After the projector 
is turned off, the cooling fans operate for 90 seconds. 
You cannot turn on the projector during this cooling 
down period.
1
2
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU 
TURN THE PROJECTOR ON, WAIT AT LEAST FIVE 
MINUTES BEFORE TURNING IT OFF.
DO NOT UNPLUG THE AC POWER CORD WHILE 
COOLING FANS ARE RUNNING OR BEFORE THE 
POWER INDICATOR LIGHTS GREEN AGAIN.
OTHERWISE IT WILL RESULT IN SHORTENING OF 
THE LAMP LIFE.
3When the projector has cooled down enough, the 
POWER indicator lights green and then you can turn on 
the projector. To unplug the AC power cord, wait until 
the projector is completely cooled down.
“Power off?” disappears after 4 seconds.
✔Note:
	 •	 When	the	On	start	function	is	set	to	“On,”	the	projector	will	be	
turned	on	automatically	by	connecting	the	 AC	power	cord	to	an	AC	
outlet	(p.52).
	 •	 The	running	speed	of	cooling	fans	is	changed	according	to	the	 temperature	inside	the	projector.
	 •	 Do	not	put	the	projector	in	a	case	before	the	projector	is	cooled	
enough.
	 •	 If	the	 WARNING	 TEMP.	indicator	blinks	red,	see	 “Warning	
Indicators”	on	page	63.
	 •	 The	projector	cannot	be	turned	on	during	the	cooling	period	with	 the	POWER	indicator	turned	off.	 You	can	turn	it	on	again	after	the	
POWER	indicator	becomes	green	again.
Turning Off the  Projector
DO NOT OPERATE THE PROJECTOR CONTINUOUSLY 
WITHOUT REST. CONTINUOUS USE MAY RESULT 
IN SHORTENING THE LAMP LIFE. TURN OFF THE 
PROJECTOR AND LET STAND FOR ABOUT AN HOUR 
IN EVERY 24 HOURS.
Basic Operation 
						

							
5

Side Control
OK button
How to Operate the On-Screen Menu
MENU button
OK button
POINT buttons
On-Screen Menu
The projector can be adjusted or set via the On-Screen 
Menu. For each adjustment and setting procedure, refer to 
the respective sections in this manual.
Use the Point 7 8 buttons to select a Menu icon. Use 
the Point ed buttons to select an item in the selected 
menu.
Press the OK button to show the item data. Use the 
Point 7 8 buttons to adjust the values.
To close the On-Screen Menu, press the MENU button 
again.
Press the MENU button on the side control or the 
remote control unit to display the On-Screen Menu.
✔Note:	 •	 The	selected	item	is	not	active	until	the	OK	button	is	pressed.
1
2
3
Remote Control Unit  
POINT buttons
OK button
MENU button
Basic Operation
Pointer(red frame)Pointer (red frame )
Press the Point ed buttons 
to move the pointer.
Item
Menu icon
Menu bar
Item data
Press the Point 7 8 
buttons to adjust the 
value.              
						

							
6

Menu Bar
For Computer Source
For Video Source
Same function as menu 
for Computer Source.
Same function as menu 
for Computer Source.
Guide Window
Show the selected 
Menu of the On-
Screen Menu.
PC System Menu
Used to select 
computer system
(p. 34).
Image Select Menu
Used to select 
an image level 
among Standard, 
High contrast, and 
Custom 1–10 (p.38).
Screen Menu
Used to adjust the size of 
the image. [Normal/True/
Wide/Full screen/Custom/
Keystone/Ceiling/Rear/Reset/
Digital zoom +/–] (pp.39-40).
Information Menu
Display the input 
source information
(p. 28).
Image Adjust Menu
Used to adjust the 
computer image. 
[Contrast/ Brightness/Color 
management/Auto picture 
control/Color temp./White 
balance (R/G/B)/Offset (R/
G/B)/Sharpness/ Gamma/
Reset/Store/Quit] 
(pp. 45–47).
PC Adjust Menu
Used to adjust 
the parameters 
to match with the 
input signal format 
(pp. 35–37).
Input Menu
Used to select an 
input source (Input 
1, Input 2, or Input 3) 
(pp. 31, 32).
Input Menu
Used to select 
an input source 
(Input 1, Input 2, 
or Input 3) 
(pp.31, 33).
Image Select Menu
Used to select an 
image level among 
Standard, Cinema, and 
Custom 1–10
(p. 42).
Image Adjust Menu
Used to adjust the picture 
image. [Contrast/Brightness/ 
Color/Tint/Color management/ 
Auto picture control/Color temp./
White balance (R/G/B)/ Offset 
(R/G/B)/Sharpness/Gamma/Noise 
reduction/Progressive/Reset/
Store/Quit] 
(pp. 45–47.)
AV System Menu
Used to select the 
system of selected 
video source
(p. 41).
For detailed functions of each menu, see “Menu Tree” on pages 66-68.
Setting Menu
Used to set 
the projector’s 
operating 
configurations 
(pp. 48–55).
Screen Menu
Used to adjust the 
size of the image. 
[Normal/Wide/Custom/
Keystone/Ceiling/Rear/
Reset] (pp. 43-44).
Basic Operation 
						

							
7

Operating with Projector Control
The following lens operation can be made with the Lens 
button on the side control. 
Press the LENS button to enter each lens operation mode. 
The selected adjustment display appears on the screen.
Display “Lens shift” on the screen. Use the Point ed7 8 
buttons to position the screen to the desired point without 
having picture distortion. 
The screen can be moved up or down to 50 percent, or 
sideways up to 10 percent from the central axis of the 
lens shift.
Lens Shift Adjustment
✔Note:
	 •	The	 arrow	disappears	 at	the	 maximum	 lens	shift	
in	each	direction.
	 •	The	 arrow	turns	red	when	 the	lens	 shift	 comes	 to	
the	center	position	of	the	screen.
Display “Zoom” on the screen. Use the Point ed buttons 
to zoom in and out the image.
Zoom Adjustment
Display “Focus” on the screen. Use the Point ed buttons 
to adjust focus of the image.
Focus Adjustment
Side Control
LENS button
Lens Operation
ZOOM
FOCUS
POINT buttons
Basic Operation
Zoom
Focus
Lens Shift 
						

							
8

Operating with Remote Control Unit
Using the remote control unit for some frequently used operations is advisable. Just pressing one of the 
buttons enables you to make the desired operation quickly without calling up the On-Screen Menu.
Press the FREEZE button on the remote control unit to 
freeze the picture on the screen. To cancel the FREEZE 
function, press the FREEZE button again or press any other 
button.
FREEZE button
Press the AUTO PC button on the remote control unit to 
operate the Auto PC Adj. function. The computer screen 
adjustment can be done easily by pressing this button. See 
page 35 for details.
AUTO PC button
Press the D-ZOOM button on the remote control unit to 
enter to the Digital zoom +/– mode. See page 40 for details.
D-ZOOM button
Press the ASPECT button on the remote control unit to 
select the desired screen size. The selected screen size 
symbol appears on the screen for 4 seconds. See pages 39 
to 40 and 43 to 44 for details.
Press and hold the ASPECT button for more than 5 seconds 
to return all the screen size adjustment setting to the factory 
default setting.
ASPECT button
Press the ZOOM buttons on the remote control unit to zoom 
in and out the image.
ZOOM buttons
Press the FOCUS buttons on the remote control unit to 
adjust focus of the image.
FOCUS buttons
See page 27 for details.
LENS-SHIFT button
Remote Control Unit
D-ZOOM 
button
INFO . 
button
POINT ed7 8 
buttons
FREEZE buttonAUTO PC
button
ASPECT button
ZOOM 
buttons
FOCUS 
buttons
LENS-SHIFT 
button
✔Note:
	 •	See	 the	next	 page	 for	the	 description	
of	other	buttons.
Information display can be used to confirm the current 
operating condition of the projector and the signal being 
projected through the projector.
Press the INFO. button on the remote control unit to 
display the information window on the screen. To hide the 
information window, press the INFO. button again or Point 7 
8 buttons.
The information window can also be selected from the 
menu.
INFO  . button
Information  Menu
Information Menu
*  The H- and V-sync freq. values described in this figure may be different from the actual values.
Basic Operation              
						

							
9

Press the BLANK button on the remote control unit to black 
out the image. To restore to normal, press the BLANK button 
again or press any other button.
BLANK button
FILTER button
Press and hold the FILTER button for more than 5 seconds 
to operate electrically operated filter to replace the filter.
KEySTONE button
Reduce  the  upper  width  with Point e button. Re d u c e   t h e   l owe r   w i d t h with Point d button.  Reduce  the  left  part  with Point 7 button.  Reduce  the  right  part  with Point 8 button.  
• The white arrows indicate that there is no correction.
•  A red arrow indicates the direction of correction.
•  An arrow disappears at the maximum correction.
•  If you press the KEYSTONE button on the remote 
control unit again while the Keystone dialog box is being displayed, the keystone adjustment will be canceled.
•  “Keystone” disappears after 10 seconds.
Press the P-TIMER button on the remote control unit. The 
Timer display “00 : 00” appears on the screen and starts to 
count time (00 : 00–59 : 59). 
To stop the P-TIMER, press the P-TIMER button. 
To cancel the P-TIMER, press the P-TIMER button again.
P-TIMER button
P-Timer display
POINTER button
Press POINTER button on the remote control unit to display 
the Pointer on the screen. 
Remote Control Unit
POINTER 
buttonP-TIMER 
button
FILTER 
button
BLANK
button
✔Note:
	 •	S e e 	t h e 	p r e v i o u s 	p a g e 	f o r 	t h e	
description	of	other	buttons.
KEy STONE 
button
Move the pointer on the screen with this button.
MOUSE POINTER button
MOUSE
POINTER 
button
Press the KEYSTONE button on the remote control unit. The 
“Keystone” appears on the screen.
Use the Point ed7 8 buttons to correct keystone 
distortion. The keystone adjustment can be stored (pp.40, 
44).
“Blank” disappears after 4 seconds.
Basic Operation
✔Note:
	 •	When	 the	filter	 is	replaced,	 the	total	 accumulated	 time	of	the	 filter	
use	is	automatically	set	to	0.              
						

							
0

Pointer Function
Pointer
✔Note:
	 •	 You	can	choose	the	pattern	of	Pointer	(Arrow/Cross/Dot)	in	the	Setting	Menu	(p.	52)
You can move the Pointer of the projector with the remote control unit to emphasize a part of the projected 
image.  
Press the POINTER button to activate the Pointer 
function.1
2
3
MOUSE POINTER button
POINTER button
To cancel the Pointer function, press the POINTER 
button again or press any other button. 
Use the MOUSE POINTER button to move the Pointer. 
Wireless Mouse Operation
The remote control unit can be used as a wireless mouse for your computer. 
Move the pointer on 
the screen with this 
button. 
MOUSE POINTER 
button
R-CLICK button
L-CLICK button
Acts as right (click) 
mouse button while 
the projector and 
a computer are 
connected with a USB 
cable.
Acts as left (click) 
mouse button while 
the projector and 
a computer are 
connected with a USB 
cable.
Before operating the wireless mouse, connect your 
computer and the projector with the supplied USB 
cable (p. 20).
When the Pointer function is used, the wireless mouse 
is not available. 
When a USB cable is connected to the computer 
and the projector, turn on the projector first, then 
the computer. If you turn on the computer first, the 
wireless mouse function may not operate properly.
1
2
Basic Operation