Canon projector LE5W WH User Manual

							21 Introduction
Remote control
1. POWER button
Turns the projector on or off. (P27, 
P30
) 
2. AUTO PC button
Automatically adjusts the projector to 
the optimum status depending on the 
computer signal when an analog PC 
signal is being input. (P35) 
Press and hold for 3 seconds to 
enable or disable the key lock. (P74)
 
3. PC button
Switches to PC/Component input. 
(P28) 
4. HDMI button
Switches to HDMI input. (P28) 
5. VIDEO button
Switches to Video input. (P28) 
6. MUTE button
Temporarily mutes the audio. (P29) 7. VOL- button
Reduces the volume. (P29) 
8. VOL+ button
Increases the volume. (P29) 
9. MENU button
Displays the On-Screen Display 
(OSD) menu. (P75)
 
10 ~ 13 ///
Directional buttons ( Up, Down, 
Left, Right ) 
Allows you to perform operations in 
menus, document viewer, etc.
14. BACK button
Returns to the upper level of the 
OSD.
Closes the pop-up setting menu of 
the OSD.
15. OK button
Confirms the selected menu item.
Allows you to perform operations in 
document viewer, etc.
16. HOME button
Displays the home screen.
 (P46) 
17. BLANK button
Temporarily hides the image. (P30) 
1
3
4
7
6
9
16 15 10
11
14
13
17
12
2
5
8
II 
						

							Introduction 22
Remote control effective range
The Infra-Red (IR) remote control sensor is on the 
front of the projector, so make sure you point the 
remote control at the front.
The remote control must be held at an angle within 
± 15 degrees vertically and ± 30 degrees horizontally 
to the projectors IR remote control sensor, and within 
a distance of approximately 8 meters.
•  You may not be able to perform operations if 
there are any obstacles between the remote 
control and the projector.
•  You may not be able to operate the remote control 
if direct sunlight or strong light is shining onto the remote IR receiver.
Installing the batteries
1. Press the knob on the battery holder to the right 
and slide it out.
2. Remove the old battery.
3. Make sure the positive side (+) of the new 
battery (CR2025) is facing up when you place 
it into the battery holder.
4. Slide the holder in until you hear it click into 
place.
Note the following points when handling batteries. Failure to do so could result in 
a fire or injury.
•  Do not place the battery in a fire, apply heat, short circuit, or disassemble the 
battery. 
•  Do not attempt to recharge the battery.
•  Remove the battery when it is drained, or if it will not be used for a long 
period of time.
•  Insert the battery in the correct + or -  position.
•  If any liquid leaks from the battery and comes into contact with skin, wash it 
off thoroughly with water.
•  The remote control battery and battery holders can be a choking hazard if 
swallowed accidentally by small children. Make sure these are placed out of 
the reach of children. If they are swallowed accidentally, contact a physician 
immediately.
Warning 
						

							23 Introduction
Third party software
This product includes third party software modules.
For more details, see the ThirdPartySoftware.pdf (third party software licenses) in 
the thirdparty_software folder on the setup CD-ROM supplied.
You can also view the licensing conditions for each module in the thirdparty_software/
LICENSE folder.
■ GPL and LGPL software licenses
This product uses software modules licensed under GPL and LGPL.
The source code is included in the thirdparty_software/GPL(LGPL) folder on the setup 
CD-ROM supplied.
■ Software programs based on the GNU General Public License 
Version 2
The software programs (these programs) included in this media are freeware. You 
can redistribute and make changes under the conditions defined in the GNU General 
Public License Version 2.
Each program is distributed in the hope that it will be useful, however they are 
provided without warranty of any kind, including, but not limited to, the implied 
warranties of merchantability and fitness for a particular purpose. See the following 
Warranty disclaimer and Third party software support. For more details see the 
GNU General Public License Version 2.
Warranty disclaimer
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO 
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY 
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE 
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM 
AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR 
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE 
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE 
PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, 
YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR 
CORRECTION.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN 
WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO 
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED 
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, 
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF 
THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT 
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR 
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE  
						

							Introduction 24
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH 
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF 
SUCH DAMAGES.
Third party software support
Canon Inc., Canons affiliated companies, as well as sales companies do not offer any 
support services for these programs. We are unable to respond to questions or inquiries 
from you or any other parties regarding these programs. 
						

							25 Projecting
Projecting 
						

							Projecting 26
Connecting the power cord
1. Connect the power cord supplied to the AC power jack on the projector.
2. Connect the plug to a wall outlet. When the power is on, the POWER button/
POWER LED indicator lights red.
Basic operations
12 
						

							27 Projecting
Turning on the projector
1. Connect the plug to a wall outlet. (P26) 
The POWER button/POWER LED indicator lights red.
2. Open the lens shutter.
3. Make sure other cables are securely 
connected. (P34) 
4. Turn on all devices connected to the 
projector.
5. Press the POWER button on the projector 
or the POWER button on the remote 
control to turn on the projector. When the 
projector turns on, the power indicator LED 
lights blue. The start up procedure takes 
several seconds, and the startup logo will be 
projected.
6. If the image is not clear, adjust the focus 
with the focus ring.
7. If the projector is turned on for the first time, 
select the display language (P28).
If the frequency/resolution of the input signal 
exceeds the projectors supported range, the 
message Out of Range is displayed. Change to 
an input signal that is supported by the projector 
(P95).
Adjusting the focus
Rotate the focus ring to adjust the focus.
PC HDMI VIDEAUT
PC
II 
						

							Projecting 28
Setting the language
If the projector is turned on for the first time, select the language for the On-Screen 
Display (OSD).
1. Press the HOME button on the remote control to open the home screen.
2. Press the   button on the remote control, select Setup, and then press the OK 
button. The Setup menu opens.
3. Press the   button on the remote control, select Language from the menu, and 
then press the OK button.
4. Press the  ,  ,  , and   buttons on the 
remote control to select your language, and 
then press the OK button.
* You can select from 19 languages. See page 52 
for details.
Switching the input signal
Perform one of the following operations to switch the input signal. 
•  Press one of the input signal buttons (PC, HDMI, or VIDEO) on the remote control.
* There are no other input signals buttons aside from PC, HDMI, and VIDEO. Press 
the PC button to display images from component video devices.
• Press the INPUT button on the projectors control panel. Each time you press the 
button, the input signal changes in the order: PC/Component, HDMI, VIDEO.
•  Select the input signal icon on the home screen, and then press the OK button.
* You then need to perform further menu operations for Internal Memory (P48), USB 
Drive (P48), SD Card (P48), and USB Streaming (P54). Refer to each corresponding 
section in this manual. 
						

							29 Projecting
The default aspect ratio for the projector is 16:10. 
Depending on the input signal, the aspect ratio 
may not be displayed correctly. If this occurs, you 
need to change the aspect ratio. See Aspect on 
page 79 for details.
When PC/Component, HDMI, or VIDEO is 
selected, the last used input signal is 
automatically selected the next time the projector 
starts up.
Adjusting volume
Follow the steps below to adjust the volume of the projectors internal speaker or the 
volume being output from the audio output jack.
Audio volume
Press the VOL-/VOL+ buttons on the remote control to 
adjust the volume.
Muting
Press the MUTE button on the remote control to 
temporarily mute the audio.
Press the MUTE button again to restore the audio.
Audio is not output when no input signal is being 
projected. However, when playing an audio file, audio can be output even when no 
image is being projected. In this situation, you can adjust the volume.
* If no audio is output for the image being projected, check that the audio input is 
connected to the projector correctly.
* When an external speaker is connected, audio is not output from the internal 
speaker.
MUTE VOL- VOL+PC HDMI VIDEOAUTO 
PC
MENU BACK MUTE VOL- VOL+PC HDMI VIDEO
MENU BACK MUTE VOL- VOL+PC HDMI VIDEO 
						

							Projecting 30
Hiding the image
Press the BLANK button on the remote control to hide the image.
Press the BLANK button again on the remote 
control or the projector to restore the image.
Do not place any objects in front of the lens 
while the projector is operating. Doing so could 
cause a fire.
Turning off the projector
1. When you press the POWER button, a 
confirmation message is displayed. 
If no operation is performed within a few 
seconds, the message disappears.
2. Press the POWER button again. 
3. The lamp turns off and the fans stop.
4. Disconnect the power cord from the wall 
outlet. 
HOME
OK
BLANK MENU BACK
Caution
PC HDMI VIDEAUT
PC
II
II
12