Canon projector LE5W BK User Manual

21 Introduction
Remote control
1. POWER button
Turns the projector on or off. (P27, 
P30
) 
2. AUTO PC button
Automatically adjusts the projector to 
the optimum status depending on the 
computer signal when an analog PC 
signal is being input. (P35) 
Press and hold for 3 seconds to 
enable or disable the key lock. (P74)
 
3. PC button
Switches to PC/Component input. 
(P28) 
4. HDMI button
Switches to HDMI input. (P28) 
5. VIDEO button
Switches to Video input. (P28) 
6. MUTE button
Temporarily mutes the...

Introduction 22
Remote control effective range
The Infra-Red (IR) remote control sensor is on the 
front of the projector, so make sure you point the 
remote control at the front.
The remote control must be held at an angle within 
± 15 degrees vertically and ± 30 degrees horizontally 
to the projectors IR remote control sensor, and within 
a distance of approximately 8 meters.
•  You may not be able to perform operations if 
there are any obstacles between the remote 
control and the projector.
•  You...

23 Introduction
Third party software
This product includes third party software modules.
For more details, see the ThirdPartySoftware.pdf (third party software licenses) in 
the thirdparty_software folder on the setup CD-ROM supplied.
You can also view the licensing conditions for each module in the thirdparty_software/
LICENSE folder.
■ GPL and LGPL software licenses
This product uses software modules licensed under GPL and LGPL.
The source code is included in the thirdparty_software/GPL(LGPL) folder on...

Introduction 24
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH 
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF 
SUCH DAMAGES.
Third party software support
Canon Inc., Canons affiliated companies, as well as sales companies do not offer any 
support services for these programs. We are unable to respond to questions or inquiries 
from you or any other parties regarding these programs. 

25 Projecting
Projecting 

Projecting 26
Connecting the power cord
1. Connect the power cord supplied to the AC power jack on the projector.
2. Connect the plug to a wall outlet. When the power is on, the POWER button/
POWER LED indicator lights red.
Basic operations
12 

27 Projecting
Turning on the projector
1. Connect the plug to a wall outlet. (P26) 
The POWER button/POWER LED indicator lights red.
2. Open the lens shutter.
3. Make sure other cables are securely 
connected. (P34) 
4. Turn on all devices connected to the 
projector.
5. Press the POWER button on the projector 
or the POWER button on the remote 
control to turn on the projector. When the 
projector turns on, the power indicator LED 
lights blue. The start up procedure takes 
several seconds, and the...

Projecting 28
Setting the language
If the projector is turned on for the first time, select the language for the On-Screen 
Display (OSD).
1. Press the HOME button on the remote control to open the home screen.
2. Press the   button on the remote control, select Setup, and then press the OK 
button. The Setup menu opens.
3. Press the   button on the remote control, select Language from the menu, and 
then press the OK button.
4. Press the  ,  ,  , and   buttons on the 
remote control to select your...

29 Projecting
The default aspect ratio for the projector is 16:10. 
Depending on the input signal, the aspect ratio 
may not be displayed correctly. If this occurs, you 
need to change the aspect ratio. See Aspect on 
page 79 for details.
When PC/Component, HDMI, or VIDEO is 
selected, the last used input signal is 
automatically selected the next time the projector 
starts up.
Adjusting volume
Follow the steps below to adjust the volume of the projectors internal speaker or the 
volume being output from...

Projecting 30
Hiding the image
Press the BLANK button on the remote control to hide the image.
Press the BLANK button again on the remote 
control or the projector to restore the image.
Do not place any objects in front of the lens 
while the projector is operating. Doing so could 
cause a fire.
Turning off the projector
1. When you press the POWER button, a 
confirmation message is displayed. 
If no operation is performed within a few 
seconds, the message disappears.
2. Press the POWER button again....