Canon printer PIXMA Pro9500 Mark II User Manual


61 2 345
34Install the ink tank
Insert the ink tank. Press the PUSH mark on the ink tank until it clicks into place.
Make sure the Ink lamp lights red. 

0
61 2 345
4
6
5
D B
C
E
Close the Top Cover (B).
Wait for about 3 minutes until the 
POWER lamp (blue) (C) stops flashing and 
stays lit then operating noise stops, and go to the next step. 
Do not open the Top Cover while the lamp is flashing. 
The printer vibrates while the lamp is flashing because ink is stirred inside the 
printer.
•
Make sure the Inner Cover (D) is closed.
•
Install all the other ink tanks in the same way.
Install all the ink tanks.
Make sure all the  Ink lamps light red....


61 2 3 45
5
Install the Software
Quit all running applications before installation.
•
To use the printer by connecting it to a computer, software including the 
drivers needs to be copied (installed) to the computer's hard disk.
The screens below are based on Windows Vista operating system 
Ultimate Edition (hereafter referred to as "Windows Vista") and Mac OS X 
v.10.5.x.
Macintosh (P.21) Windows (P.12)
You need to log on as the administrator (or a member of the Administrators...


5
2
1
A
B
Windows Macintosh
If the Found New Hardware or Found New 
Hardware Wizard dialog box appears:
Remove the USB cable connected to 
your computer. TURN OFF THE PRINTER (A).
Turn on the computer, then insert the Setup CD-
ROM into the CD-ROM drive.
The setup program should start automatically.
If the program does not start automatically, double-click 
the CD-ROM icon on the computer. When the CD-ROM 
contents appear, double-click MSETUP4.EXE.
•
Windows Vista
Windows XP/2000 Go to Step ....


61 2 3 45
34
WindowsMacintosh
AutoPlay screen appears, click 
Run Msetup4.exe. User Account Control dialog box appears, click  Continue.
If the same dialog box reappears in subsequent steps, click  Continue.
Windows Vista Windows Vista 


5
65
WindowsMacintosh
Click Install.
Move the cursor over items to display explanations.
•
Click Easy Install.
Drivers, application software, and on-screen manuals are installed autom\
atically.
If you want to select particular items to install, click  Custom Install and follow the on-screen instructions to 
proceed with the installation.
•
You can install the XPS Printer Driver from  Custom Install. (Windows Vista SP1 or later.)
•
When installing the XPS Printer Driver, select the IJ Printer...


61 2 3 45
78
WindowsMacintosh
Read the License Agreement screen carefully and click 
Yes.
During installation, follow any on-screen instructions to install the so\
ftware.
•
When the Please Allow All Install Wizard Processes  screen appears, click 
Next.
Installation starts. 


5
910
A
WindowsMacintosh
When the Printer Connection screen appears, connect the printer to the computer with a 
USB cable.
If installation does not continue after 10 minutes, click  Help on the screen in 
step , then confirm the message.
•
When the printer is recognized by the computer, a message appears on 
the screen.
It takes about 30 seconds for the POWER lamp to light blue.
•
Turn on the printer (A).
The USB port is located on the right side of the printer.
• 


61 2 3 45
1112
C
D
Windows Macintosh
When the Print Head Alignment
 screen appears, load two sheets of A4 or Letter-sized plain 
paper in the Rear Tray (C) as shown. Align the Print Head
For details, refer to "6 Loading Paper" on page 28.
•
Click Execute.
Pinch and slide the Paper Guide (D) against the left edge of the paper\
. 


5
14
13
F
EG
Windows
Macintosh
When the Start Print Head Alignment dialog box appears, click 
Align Print Head .
Click OK in the subsequent message.
Printing of the pattern starts.
Wait until the pattern printing ends (about 10 minutes), and go to 
the next step.
•
If you align the Print Head automatically again, patterns different from those shown above may be 
printed.
•
Make sure that the pattern shown is printed, then click 
Next on the Print Head 
Alignment screen.
Some parts of patterns...