Canon printer PIXMA MG7520 User Manual

Changing the Machine Settings Using the Operation Panel
Changing the Machine Settings Using the Operation Panel
Print settings
LAN settings
Device user settings
PictBridge print settings
Language selection
Home screen background color
Firmware update
Cassette settings
Reset setting
About ECO settings
About Quiet setting
Using the Machine with the Access Point Mode
261 

Changing the Machine Settings Using the Operation PanelThis section describes the procedure to change the settings in the  Device settings screen, taking the steps
to specify  Extended copy amount  as an example.1.
Make sure that the machine is turned on.
2.
Flick the HOME screen, then tap  Setup .
Using the Operation Panel
3.
Tap  Device settings .
The  Device settings  screen is displayed.
4.
Tap the setting item to adjust.
The setting screen for the selected item is displayed.
5.
Tap the setting...

You can select the setting menus below.
Print settings
LAN settings
Device user settings
PictBridge print settings
Language selection
Home screen background color
Firmware update
Cassette settings
Reset setting
Note
•
You can use the machine considering the environment, such as setting 2-sided printing as default orenabling the machine to turn on/off automatically.
About ECO settings
•
You can reduce the operating noise when printing at night.
About Quiet setting
263 

Print settings•
Prevent paper abrasion
Use this setting only if the print surface becomes smudged.
Important
•
Be sure to set this back to  OFF after printing since it may result in lower printing speed or lower
print quality.
•
Extended copy amount
Selects the amount of image that extends off the paper when printing in borderless (full). Slight cropping may occur at the edges since the copied image is enlarged to fill the whole page. You
can change the width to be cropped from the borders of the...

Important•
For Letter-sized or Legal-sized paper, you can adjust the left/right margins between -0.05inches/-1.5 mm and +0.05 inches/+1.5 mm even if you specify the value over 0.05 inches/1.5 mm.265 

LAN settings•
Change LAN
Enables either wireless LAN, wired LAN, or access point mode. You can also disable all.
•
Wireless LAN setup
Selects the setup method for wireless LAN connection.
Note
•
You can also enter this setting menu by selecting  WLAN on the HOME screen. In this case, enable
wireless LAN.
When this menu is selected, the machine starts searching for a WPS-compatible access point. If the
machine detects the access point, follow the on-screen instructions to set up wireless LAN. If an...

ConnectionActive/InactiveSSIDXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXCommunication modeInfrastructureChannelXXWireless LAN securityInactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-
PSK(TKIP)/WPA2-PSK(AES)IPv4 addressXXX. XXX. XXX. XXXIPv4 subnet maskXXX. XXX. XXX. XXXIPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec...

IPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsEnable (ESP)/Enable (ESP & AH)/Enable (AH)/DisablePre-shared keyXXXXXXXXXXXXXXXXPrinter nameXXXXXXXXXXXXXXXBonjour service nameXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
◦
AP mode setting list
The list of access point mode settings of this machine is displayed on the touch screen. The following setting items are displayed....

Bonjour service nameXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
◦
Print LAN details
You can print out the network settings of the machine such as its IP address and SSID.
For more information on the machine's network setting is printed out:
Printing Out Network Setting Information
Important
•
This printout contains valuable information about your computer. Handle it with care.
•
Other settings
Important
•
You cannot select the items below...

Timeout settingSpecifies the timeout length.◦
Bonjour settings
Setting items for LAN using Bonjour for Mac OS.
Enable/disable Bonjour Selecting  Enable allows you to use Bonjour to perform the network settings.
Service name Specifies the Bonjour service name. You can use up to 48 characters for the name.
Note
•
You cannot use the same service name as that already used for other LAN connected devices.
◦
LPR protocol setting
Activates/deactivates the LPR setting.
◦
PictBridge communication
Setting items...